Bosch MIC Series 400 Bedienungsanleitung

Bosch Security Systems Issue 1

MIC400 Quick Start Guide

Unit Mechanical mounting

The upright unit can be mounted either way up with the camera ball up or down. The get the picture the correct

way up for installation with camera ball down rotate the camera tilt axis over by 180 degrees.

Please refer to the MIC400 Manual for further details of configuring Image Flip and reversing the controls for IR

unit and inverted units.

The MIC400, if canted is designed only to be mounted ball up, the tilt limits for the canted unit prevent it from

working properly if mounted ball down, the MIC412 and MIC440 cannot be canted.

WARNING: INSTALLATION SHOULD BE CARRIED OUT BY QUALIFIED

PERSONNEL ONLY IN ACCORDANCE WITH THE APPLICABLE LOCAL

CODES.

BOSCH SECURITY SYSTEM ACCEPTS NO LIABILITY FOR ANY

DAMAGES OR LOSSES CAUSED DUE TO INCORRECT OR IMPROPER

INSTALLATION.

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,

DISCONNECT POWER SUPPLY BEFORE OPENING THE POWER

SUPPLY UNIT.

POWER DISCONNECT: POWER SUPPLY UNITS HAVE POWER

SUPPLIED WHENEVER THE POWER CORD IS INSERTED INTO THE

POWER SOURCE

WARNING: DUE CAUTION SHOULD BE EXERCISED WHEN

INSTALLING THE MIC400 RANGE OF CAMERAS, COMMON SENSE

PRECAUTIONS SUCH AS FITTING A SAFETY CHAIN SHOULD BE

FOLLOWED.

SPECIAL CARE SHOULD BE TAKEN WITH STAINLESS STEEL, MIC412

or MIC440 MODELS DUE TO THEIR EXTRA WEIGHT.

Page 2 of 3

BOSCH SECURITY SYSTEMS

Do not manually back drive the pan or tilt axis by hand. Back driving may strip teeth off the internal gears

and in so doing will void the warranty.

M8 Stainless steel nuts, bolts and washers should be used to secure the base to the mounting surface. Suitable

sealant or a gasket should be used between the camera base and the mounting surface.

Ensure that the 12 pin connector is located into the camera base plug and that the lock ring is tightened. Ensure

that the base compartment containing the 12 way connector is moisture proof. On inverted units it is very

important that the connector area is water tight to prevent water pooling around the connector.

The MiC400 series of PTZ cameras comes with a security attachment point as standard. This should be attached

to a safety chain which in turn should be attached to a secure part of the structure.

Earthing the camera

The camera and camera housing are electrically isolated so the housing should be safety earthed regardless.

This safety earth should be a bonding connection to the camera’s outside case. E.g. one of the securing screws

used for bolting the camera down.

The camera should be earthed at one point only to prevent earth loops and thus hum bars appearing on the

camera picture in the control room.

Connections between the MIC400 and the MIC-PSU using the MIC Composite Cable:

Note: all connections must be made

MIC400 Composite

Cable Wire Colour

Function PSU Terminal

Connector

PSU Terminal ID

marking

Red 15v AC supply HD3-1 Power

Green 15v AC supply return HD3-2 Power

White Camera Rx B HD3-3 RxB

Yellow Camera Rx A HD3-4 RxA

Drain Wire Gnd HD3-5 GND

Blue Camera Tx A HD3-6 TxA

Violet Camera Tx B HD3-7 TxB

Coax Core Video HD3-8 Video

Coax Screen Video Return HD3-9 Vid 0v

Page 3 of 3

BOSCH SECURITY SYSTEMS

Black Tamper Switch HD3-10 Tamp Sw

Orange Wash HD3-11 Wash

Grey 0v Tamper Switch. HD6-1

Brown 0v Wash HD6-2

IR lamp, Heater or

Speaker Option

Grey IR Lamp + or Speaker +

or Heater +

HD6-1 IR +

Brown IR Lamp- or Speaker -

or Heater -

HD6-2 IR -

External Connections to the Power Supply Unit

Please Note:

Cameras are supplied set to address 1, to change the address and configure the camera you will require the

Universal CamSet program and a PC with a serial port and an RS232 to RS485/RS422 adaptor. A PC without a

serial port can use the MIC-USB485 CVTR to connect to the MIC-PSU instead.

TELEMETRY

Signal Function Telemetry Signal Name HD4 or

HD5

RS485 + to camera RXB Pin 1

RS485 – to camera RXA Pin 2

0v from control room. GND Pin 3

RS485 – to control

room.

TXA Pin 4

RS485 + to control

room.

TXB Pin 5

MAINS

Live HD1-1

Neutral HD1-2

Earth HD1-3

VIDEO

Video BNC CN1 Connection

Core Video to Control Room

Screen Video GND to Control Room

Andere Handbücher für MIC Series 400

Andere Bosch Sicherheitskamera Handbücher

Bosch

Bosch DINION XF LTC 0495 Installationsanleitung

Bosch

Bosch EX49 Bedienungsanleitung

Bosch

Bosch AUTODOME IP starlight 5000i IR Bedienungsanleitung

Bosch

Bosch NII-51022-V3 Bedienungsanleitung

Bosch

Bosch Dinion XF LTC 0495/61 Bedienungsanleitung

Bosch

Bosch VDN-240 Gebrauchsanweisung

Bosch

Bosch VTC-206 Series Bedienungsanleitung

Bosch

Bosch VDx-244 Bedienungsanleitung

Bosch

Bosch WZ20 Bedienungsanleitung

Bosch

Bosch DINION IP starlight 6000 HD Bedienungsanleitung

Bosch

Bosch MIC IP fusion 9000i Bedienungsanleitung

Bosch

Bosch DinionHD NBN-921 Bedienungsanleitung

Bosch

Bosch AUTODOME IP starlight 5000i Bedienungsanleitung

Bosch

Bosch MIC IP ultra 7100i Bedienungsanleitung

Bosch

Bosch FLEXIDOME IP indoor 5000 Betriebsanleitung

Bosch

Bosch VEZ Series Bedienungsanleitung

Bosch

Bosch Dinion XF LTC 0610 series Bedienungsanleitung

Bosch

Bosch MIC IP fusion 9000i Bedienungsanleitung

Bosch

Bosch LTC 0510 Series Bedienungsanleitung

Bosch

Bosch EX14 Series Bedienungsanleitung

Bosch

Bosch NPD-5512-Z30 Bedienungsanleitung

Bosch

Bosch Autodome IP 4000 HD Bedienungsanleitung

Bosch

Bosch LTC-0498-21 Bedienungsanleitung

Bosch

Bosch REG-X Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung