Bosch VCD Series Bedienungsanleitung

HD Conference Dome

VCD Series

en Installation Manual

HD Conference Dome Table of Contents | en 3

Bosch Security Systems, Inc. Installation Manual F.01U.265.806 | 1.0 | 2012.03

Table of Contents

1Safety 7

1.1 Important Safety Instructions 7

1.2 Safety Precautions 10

1.3 Important Notices 11

1.4 Customer Support and Service 18

2 Unpacking 19

2.1 Parts List 19

2.2 Safety Rules 19

3 Description 20

4 Installing a Surface Mount 22

4.1 Description 22

4.1.1 Additional Tools Required 22

4.1.2 Preparing the Surface Mount for an Indoor Installation 23

4.1.3 Installing the Camera to the Mounting Plate 24

5 Installing a Wall Mount 28

5.1 Description 28

5.1.1 Additional Tools Required 28

5.1.2 Preparing the Wall Mount for an Indoor Installation 29

5.1.3 Installing the Camera to the Mounting Plate 31

6 Installing a Recessed Mount 35

6.1 Description 35

6.1.1 Additional Requirements 35

6.1.2 Preparing the Ceiling for Installation 36

6.1.3 Installing the Camera to the Mounting Plate 39

7 Installing a Pipe Mount 44

7.1 Description 44

7.1.1 Tools/Supplies Required 44

7.1.2 Preparing the Ceiling for Installation 45

7.1.3 Installing the Camera to the Mounting Plate 48

4en | Table of Contents HD Conference Dome

F.01U.265.806 | 1.0 | 2012.03 Installation Manual Bosch Security Systems, Inc.

8 Preparing the Wiring 51

8.1 Power 51

8.2 Power Connections 52

8.2.1 Power Connections to Indoor Cameras 52

8.3 Video Connection 53

8.4 Connecting the Video 54

8.5 Ethernet Connection 55

9 Audio, Alarms and Relay Connections 56

9.1 Alarm Input 56

9.2 Connecting Alarms (inputs 1 through 2) 57

9.2.1 Connecting a Normally Open Alarm 57

9.2.2 Connecting a Normally Closed Alarm 58

9.3 Alarm Outputs 59

9.3.1 Connecting an Open Collector Output 59

9.4 Audio Cables 60

10 Getting Started 61

10.1 Powering On 61

11 Using the IP Interface 62

11.1 Overview of Features 62

11.2 System Requirements 63

11.3 Connecting the HD Conference Dome to the PC 64

11.4 Configuring the HD Conference Dome Camera 65

11.4.1 Changing the Network Settings 66

11.5 The Livepage 69

11.5.1 Entering a Keyboard Control Command 74

11.6 Saving Snapshots 76

11.7 Recording Video Sequences 76

11.8 Processor Load 77

11.9 The RECORDINGS Page 77

HD Conference Dome Table of Contents | en 5

Bosch Security Systems, Inc. Installation Manual F.01U.265.806 | 1.0 | 2012.03

12 Configuring the HD Conference Dome 80

12.1 Basic Mode: Device Access 81

12.2 Basic Mode: Date/Time 82

12.3 Basic Mode: Network 83

12.4 Basic Mode: Encoder 84

12.5 Basic Mode: Audio 86

12.6 Basic Mode: Recording 86

12.7 Basic Mode: System Overview 87

12.8 Advanced Mode: General 87

12.9 Identification 87

12.10 Password 88

12.11 Date/Time 89

12.12 Display Stamping 91

12.13 Advanced Mode: Web Interface 93

12.14 Appearance 93

12.15 Livepage Functions 94

12.16 Logging 96

12.17 Advanced Mode: Camera 96

12.18 Installer Menu 96

12.19 Encoder Profile 97

12.20 Encoder Streams 102

12.21 Privacy Masks 104

12.22 Camera Settings 105

12.23 Lens Settings 107

12.24 PTZ Settings 109

12.25 Diagnostics 110

12.26 Preposition and Tours 110

12.27 Sectors 112

12.28 Miscellaneous 112

12.29 Logs 112

12.30 Audio 113

12.31 Advanced Mode: Recording 114

12.32 Storage Management 114

12.33 Recording Profiles 117

12.34 Retention Time 119

12.35 Recording Schedule 119

6en | Table of Contents HD Conference Dome

F.01U.265.806 | 1.0 | 2012.03 Installation Manual Bosch Security Systems, Inc.

12.36 Recording Status 121

12.37 Advanced Mode: Alarm 121

12.38 Alarm Connections 121

12.39 VCA 125

12.40 Audio Alarm 131

12.41 Alarm E-Mail 132

12.42 Alarm Task Editor 134

12.43 Alarm Rules 134

12.44 Advanced Mode: Interfaces 135

12.45 Alarm Inputs 135

12.46 Relay 136

12.47 Advanced Mode: Network 137

12.48 Network Access 137

12.49 Advanced 141

12.50 Multicast 144

12.51 FTP Posting 145

12.52 Encryption 146

12.53 Advanced Mode: Service 147

12.54 Maintenance 147

12.55 Licenses 149

12.56 System Overview 149

13 Keyboard Commands by Number 150

14 Preventive Maintenance 151

15 Troubleshooting 152

15.1 HD Conference Dome Operation and Control 153

16 BVIP Firmware Updates 154

16.1 Upgrading the HD Conference Dome 154

16.2 Beginning the Firmware Update Process 155

Index 156

HD Conference Dome Safety | en 7

Bosch Security Systems, Inc. Installation Manual F.01U.265.806 | 1.0 | 2012.03

1Safety

1.1 Important Safety Instructions

Read, follow, and retain for future reference all of the following

safety instructions. Heed all warnings on the unit and in the

operating instructions before operating the unit.

1. Cleaning - Unplug the unit from the outlet before cleaning.

Follow any instructions provided with the unit. It is

generally sufficient to use a dry cloth for cleaning, but a

moist lint-free cloth or leather shammy may also be used.

Do not use liquid cleaners or aerosol cleaners.

2. Heat sources - Do not install the unit near any heat

sources such as radiators, heaters, stoves, or other devices

(including amplifiers) that produce heat.

3. Ventilation - Any openings in the unit housing are provided

for ventilation to prevent overheating and ensure reliable

operation. Do not block or cover these openings. Do not

place the unit in an enclosure unless proper ventilation is

provided, or the manufacturer's instructions have been

adhered to.

4. Water - Do not use this unit near water, for example near a

bathtub, washbowl, sink, laundry basket, in a damp or wet

basement, near a swimming pool, or in any area classified

as a wet location. To reduce the risk of fire or electrical

shock, do not expose this unit to rain or moisture.

5. Object and liquid entry - Never push objects of any kind

into this unit through openings, as they may touch

dangerous voltage points or short out parts, which could

result in a fire or electrical shock. Never spill liquid of any

kind on the unit. Do not place objects filled with liquids,

such as vases or cups, on the unit.

6. Lightning - For added protection during a lightning storm,

or when leaving this unit unattended and unused for long

periods, unplug the unit from the wall outlet and

disconnect the cable system. This will prevent damage to

the unit from lightning and power line surges.

8en | Safety HD Conference Dome

F.01U.265.806 | 1.0 | 2012.03 Installation Manual Bosch Security Systems, Inc.

7. Control adjustment - Adjust only those controls specified

in the operating instructions. Improper adjustment of

other controls may cause damage to the unit. Use of

controls or adjustments, or performance of procedures

other than those specified, may result in hazardous

radiation exposure.

8. Overloading - Do not overload outlets and extension cords.

This can cause fire or electrical shock.

9. Power disconnect - Units with or without ON/OFF

switches have power supplied whenever the power cord is

inserted into the power source; however, the unit is

operational only when the ON/OFF switch is in the ON

position. The power cord is the main power disconnect

device for switching off the voltage for all units.

10. Power sources - Operate the unit only via the type of

power source indicated on the label. Before proceeding,

be sure to disconnect the power from the cable being

connected to the unit.

– For battery powered units, refer to the operating

instructions.

– For units supplied by an external power source, use

only the recommended or approved power supplies.

– For limited power source units, this power source

must comply with EN60950. Substitutions may

damage the unit or cause fire or shock.

– For 24 VAC units, the VG4-A-PSUxx Power Supply is

recommended to comply with EN 50130-4 Main

Supply Voltage Dips and Short Interruption

requirement and voltage applied to the unit's power

input should not exceed +/- 10% or 21.6-26.4 VAC.

User-supplied wiring must comply with local electrical

codes (Class 2 power levels). Do not ground the

supply at the terminals or at the unit's power supply

terminals.

– If unsure of the type of power supply to use, contact

your dealer or local power company.

HD Conference Dome Safety | en 9

Bosch Security Systems, Inc. Installation Manual F.01U.265.806 | 1.0 | 2012.03

11. Servicing - Do not attempt to service this unit yourself.

Opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified

service personnel.

12. Damage requiring service - Unplug the unit from the main

AC power source and refer servicing to qualified service

personnel when any damage to the equipment has

occurred, for example if:

– the power supply cord or plug is damaged

– exposure to moisture, water, and/or inclement

weather (rain, snow etc.)

– liquid has been spilled in or on the equipment

– an object has fallen into the unit

– the unit has been dropped or the unit cabinet is

damaged

– the unit exhibits a distinct change in performance

– the unit does not operate normally when the user

correctly follows the operating instructions.

13. Replacement parts - Be sure the service technician uses

replacement parts specified by the manufacturer, or that

they have the same characteristics as the original parts.

Unauthorized substitutions may cause fire, electrical

shock, or other hazards.

14. Safety check - Safety checks should be performed on

completion of service or repairs to the unit, to ensure that

the unit is in proper operating condition.

15. Installation - Install in accordance with the manufacturer's

instructions and in accordance with applicable local codes.

16. Attachments, changes, or modifications - Only use

attachments/accessories specified by the manufacturer.

Any change to or modification of the equipment not

expressly approved by Bosch could void the warranty or, in

the case of an authorization agreement, authority to

operate the equipment.

10 en | Safety HD Conference Dome

F.01U.265.806 | 1.0 | 2012.03 Installation Manual Bosch Security Systems, Inc.

1.2 Safety Precautions

DANGER!

This symbol indicates an imminently hazardous situation such

as “Dangerous Voltage” inside the product. If not avoided, this

will result in an electrical shock, serious bodily injury, or death.

WARNING!

Indicates a potentially hazardous situation. If not avoided, this

may result in minor or moderate injury. Alerts the user to

important instructions accompanying the unit.

CAUTION!

Indicates a potentially hazardous situation. If not avoided, this

may result in damage to property or risk of damage to the unit.

NOTICE!

This symbol indicates information or a company policy that

relates directly or indirectly to the safety of personnel or

protection of property.

Inhaltsverzeichnis

Andere Bosch Sicherheitskamera Handbücher

Bosch

Bosch EXTEGRA IP 9000 FX Bedienungsanleitung

Bosch

Bosch AutoDome Installationsanleitung

Bosch

Bosch VDN-498V03-21S Bedienungsanleitung

Bosch

Bosch DINION 3100i IR NBE-3702-AL Bedienungsanleitung

Bosch

Bosch HD Conference Dome Camera Bedienungsanleitung

Bosch

Bosch 200 Series Bedienungsanleitung

Bosch

Bosch MIC-7130-PB4 Bedienungsanleitung

Bosch

Bosch AutoDome 100 Series Bedienungsanleitung

Bosch

Bosch NDS-5703-F360 Bedienungsanleitung

Bosch

Bosch VEN-650 Series Bedienungsanleitung

Bosch

Bosch FLEXIDOME AN outdoor 4000 Bedienungsanleitung

Bosch

Bosch VEZ IP Series Bedienungsanleitung

Bosch

Bosch VEZ Series Leitfaden

Bosch

Bosch WZ16 Bedienungsanleitung

Bosch

Bosch DINION 5100i IR Bedienungsanleitung

Bosch

Bosch FlexiDomeXT LTC 1361/10 Bedienungsanleitung

Bosch

Bosch VBN-5085 Bedienungsanleitung

Bosch

Bosch KBE-335V55-20 Bedienungsanleitung

Bosch

Bosch AUTODOME IP 4000i Bedienungsanleitung

Bosch

Bosch Junior Installationsanleitung

Bosch

Bosch DINION IP 4000 HD Bedienungsanleitung

Bosch

Bosch VKC 4075 Bedienungsanleitung

Bosch

Bosch DINION 7100i IR Bedienungsanleitung

Bosch

Bosch VC973650T Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung