Bosch VEZ Series Bedienungsanleitung

AutoDome Easy II

VEZ Series

en User Manual

AutoDome Easy II Table of Contents | en iii

Bosch Security Systems, Inc. User Manual F.01U.139.424 | 2.0 | 2009.08

Table of Contents

1Safety 1

1.1 Important Safety Instructions 1

1.2 Safety Precautions 4

1.3 Important Notices 4

1.4 Customer Support and Service 11

2 Unpacking 13

2.1 Parts List 13

2.2 Safety Rules 14

3 Description 15

4 Installing a Surface Mount 17

4.1 Description 17

4.1.1 Additional Tools Required 17

4.1.2 Preparing the Surface Mount for Installation 18

4.1.3 Installing the Camera to the Mounting Plate 19

5 Installing a Wall Mount 23

5.1 Description 23

5.1.1 Additional Tools Required 23

5.1.2 Preparing the Wall Mount for Installation 24

5.1.3 Installing the Camera to the Mounting Plate 26

6 Installing a Recessed Mount 29

6.1 Description 29

6.1.1 Additional Requirements 29

6.1.2 Preparing the Ceiling for Installation 30

6.1.3 Installing the Camera to the Mounting Plate 33

iv en | Table of Contents AutoDome Easy II

F.01U.139.424 | 2.0 | 2009.08 User Manual Bosch Security Systems, Inc.

7 Installing a Pipe Mount 37

7.1 Description 37

7.1.1 Tools/Supplies Required 37

7.1.2 Preparing the Ceiling for Installation 38

7.1.3 Installing the Camera to the Mounting Plate 41

8 Preparing the Wiring 43

8.1 Power 43

8.2 Connecting the Power 43

8.3 Video and Bilinx Cables 44

8.4 Connecting the Video 45

8.5 Control-only Cables 45

8.5.1 Biphase 45

8.5.2 Direct Control 46

8.5.3 Daisy Chaining 47

8.5.4 RS485 48

9 Alarms and Relay Connections 51

9.1 Alarm Input 51

9.2 Connecting Alarms (inputs 1 through 2) 51

9.2.1 Connecting a Normally Open Alarm 51

9.2.2 Connecting a Normally Closed Alarm 52

9.3 Alarm Outputs 53

9.3.1 Connecting an Open Collector Output 53

10 Getting Started 55

10.1 Powering On 55

10.2 Establishing AutoDome Easy II Control 55

10.2.1 Basic Keyboard Operation 56

10.2.2 Keyboard Commands 57

10.3 Setting the Camera Address 57

10.3.1 FastAddress 58

AutoDome Easy II Table of Contents | en v

Bosch Security Systems, Inc. User Manual F.01U.139.424 | 2.0 | 2009.08

11 On-Screen Display Menu Navigation 61

11.1 Setup Menu 61

11.2 Camera Setup Menu 63

11.3 Lens Setup 66

11.4 PTZ Setup Menu 69

11.5 Display Setup Menu 71

11.6 Communication Setup Menu 74

11.7 Alarm I/O Setup 76

11.8 Alarm I/O Rule Setup Menu 79

11.9 Language Menu 82

11.10 Diagnostics Menu 83

12 Common User Commands (unlocked) 85

12.1 Setting AutoPan Mode 85

12.2 Setting Preset Shots 85

12.3 Configuring Preposition Tours 86

12.4 Programming the Inactivity Operation 87

12.5 Recorded Tours 87

13 Pelco On-Screen Menus 89

13.1 Setup Menu 89

13.1.1 Command Lock (locked) 91

13.1.2 Bosch Menu (locked) 91

13.1.3 PTZ Setup (unlocked) 93

13.1.4 Other Menus 95

14 Keyboard Commands by Number 97

15 Preventive Maintenance 103

16 Troubleshooting 105

16.1 AutoDome Easy II Operation and Control 106

vi en | Table of Contents AutoDome Easy II

F.01U.139.424 | 2.0 | 2009.08 User Manual Bosch Security Systems, Inc.

17 Alternative Control Protocols 111

17.1 Setting FastAddress with Alternative Protocols 111

17.1.1 Using a Pelco Controller 111

17.2 Pelco Protocol Mode 112

17.2.1 Hardware Configuration 113

17.2.2 Pelco Keyboard Commands 113

17.2.3 Pelco Keyboard Commands 114

17.2.4 Special Preset Commands 115

Index 117

AutoDome Easy II Safety | en 1

Bosch Security Systems, Inc. User Manual F.01U.139.424 | 2.0 | 2009.08

1Safety

1.1 Important Safety Instructions

Read, follow, and retain for future reference all of the following

safety instructions. Heed all warnings on the unit and in the

operating instructions before operating the unit.

1. Cleaning - Unplug the unit from the outlet before cleaning.

Follow any instructions provided with the unit. It is

generally sufficient to use a dry cloth for cleaning, but a

moist lint-free cloth or leather shammy may also be used.

Do not use liquid cleaners or aerosol cleaners.

2. Heat sources - Do not install the unit near any heat

sources such as radiators, heaters, stoves, or other devices

(including amplifiers) that produce heat.

3. Ventilation - Any openings in the unit housing are provided

for ventilation to prevent overheating and ensure reliable

operation. Do not block or cover these openings. Do not

place the unit in an enclosure unless proper ventilation is

provided, or the manufacturer's instructions have been

adhered to.

4. Water - Do not use this unit near water, for example near a

bathtub, washbowl, sink, laundry basket, in a damp or wet

basement, near a swimming pool, in an outdoor

installation, or in any area classified as a wet location. To

reduce the risk of fire or electrical shock, do not expose

this unit to rain or moisture.

5. Object and liquid entry - Never push objects of any kind

into this unit through openings, as they may touch

dangerous voltage points or short out parts, which could

result in a fire or electrical shock. Never spill liquid of any

kind on the unit. Do not place objects filled with liquids,

such as vases or cups, on the unit.

6. Lightning - For added protection during a lightning storm,

or when leaving this unit unattended and unused for long

periods, unplug the unit from the wall outlet and

2en | Safety AutoDome Easy II

F.01U.139.424 | 2.0 | 2009.08 User Manual Bosch Security Systems, Inc.

disconnect the cable system. This will prevent damage to

the unit from lightning and power line surges.

7. Control adjustment - Adjust only those controls specified

in the operating instructions. Improper adjustment of

other controls may cause damage to the unit. Use of

controls or adjustments, or performance of procedures

other than those specified, may result in hazardous

radiation exposure.

8. Overloading - Do not overload outlets and extension cords.

This can cause fire or electrical shock.

9. Power disconnect - Units with or without ON/OFF

switches have power supplied whenever the power cord is

inserted into the power source; however, the unit is

operational only when the ON/OFF switch is in the ON

position. The power cord is the main power disconnect

device for switching off the voltage for all units.

10. Power sources - Operate the unit only via the type of

power source indicated on the label. Before proceeding,

be sure to disconnect the power from the cable being

connected to the unit.

– For battery powered units, refer to the operating

instructions.

– For units supplied by an external power source, use

only the recommended or approved power supplies.

– For limited power source units, this power source

must comply with EN60950. Substitutions may

damage the unit or cause fire or shock.

– For 24 VAC units, voltage applied to the unit's power

input should not exceed +/- 10% or 21.6-26.4 VAC.

User-supplied wiring must comply with local electrical

codes (Class 2 power levels). Do not ground the

supply at the terminals or at the unit's power supply

terminals.

– If unsure of the type of power supply to use, contact

your dealer or local power company.

AutoDome Easy II Safety | en 3

Bosch Security Systems, Inc. User Manual F.01U.139.424 | 2.0 | 2009.08

11. Servicing - Do not attempt to service this unit yourself.

Opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified

service personnel.

12. Damage requiring service - Unplug the unit from the main

AC power source and refer servicing to qualified service

personnel when any damage to the equipment has

occurred, for example if:

– the power supply cord or plug is damaged

– exposure to moisture, water, and/or inclement

weather (rain, snow etc.)

– liquid has been spilled in or on the equipment

– an object has fallen into the unit

– the unit has been dropped or the unit cabinet is

damaged

– the unit exhibits a distinct change in performance

– the unit does not operate normally when the user

correctly follows the operating instructions.

13. Replacement parts - Be sure the service technician uses

replacement parts specified by the manufacturer, or that

they have the same characteristics as the original parts.

Unauthorized substitutions may cause fire, electrical

shock, or other hazards.

14. Safety check - Safety checks should be performed on

completion of service or repairs to the unit, to ensure that

the unit is in proper operating condition.

15. Installation - Install in accordance with the manufacturer's

instructions and in accordance with applicable local codes.

16. Attachments, changes, or modifications - Only use

attachments/accessories specified by the manufacturer.

Any change to or modification of the equipment not

expressly approved by Bosch could void the warranty or, in

the case of an authorization agreement, authority to

operate the equipment.

4en | Safety AutoDome Easy II

F.01U.139.424 | 2.0 | 2009.08 User Manual Bosch Security Systems, Inc.

1.2 Safety Precautions

1.3 Important Notices

Accessories - Do not place this unit on an unstable stand,

tripod, bracket, or mount. The unit may fall, causing serious

injury to persons and/or severe damage to the unit. Use only

with the cart, stand, tripod, bracket, or table specified by the

manufacturer. When a cart is used, exercise caution and care

when moving the cart/apparatus combination to avoid tipping it

over, which could result in injury. Quick stops, excessive force,

or uneven surfaces may cause the cart/unit combination to

overturn. Mount the unit in line with the manufacturer's

instructions.

All-pole power switch - Incorporate an all-pole power switch,

with a contact separation of at least 3 mm in each pole, into the

electrical installation of the building. If it is needed to open the

housing for servicing and/or other activities, use this all-pole

DANGER!

This symbol indicates an imminently hazardous situation such

as “Dangerous Voltage” inside the product. If not avoided, this

will result in an electrical shock, serious bodily injury, or death.

WARNING!

Indicates a potentially hazardous situation. If not avoided, this

may result in minor or moderate injury. Alerts the user to

important instructions accompanying the unit.

CAUTION!

Indicates a potentially hazardous situation. If not avoided, this

may result in damage to property or risk of damage to the unit.

NOTICE! This symbol indicates information or a company policy

that relates directly or indirectly to the safety of personnel or

protection of property.

Andere Handbücher für VEZ Series

Inhaltsverzeichnis

Andere Bosch Sicherheitskamera Handbücher

Bosch

Bosch DCN-SWSACC Montageanleitung

Bosch

Bosch AUTODOME 7000 HD Handbuch

Bosch

Bosch DINION IP 4000 HD Bedienungsanleitung

Bosch

Bosch NBN-498-21P Bedienungsanleitung

Bosch

Bosch VDC-455V04-20S Bedienungsanleitung

Bosch

Bosch FlexiDome NDN-832 Bedienungsanleitung

Bosch

Bosch Dinion Bedienungsanleitung

Bosch

Bosch DinionHD NBN-832-38W Bedienungsanleitung

Bosch

Bosch NDS-5703-F360 Bedienungsanleitung

Bosch

Bosch DINION XF LTC 0495 Installationsanleitung

Bosch

Bosch MIC Series 550 Bedienungsanleitung

Bosch

Bosch EX49 Bedienungsanleitung

Bosch

Bosch VG4-200 Series Bedienungsanleitung

Bosch

Bosch VDC-480V03-20S Bedienungsanleitung

Bosch

Bosch EX10C704B‑N Bedienungsanleitung

Bosch

Bosch FLEXIDOME IP starlight 8000i Bedienungsanleitung

Bosch

Bosch REG-L1 Bedienungsanleitung

Bosch

Bosch NBN-80122 Bedienungsanleitung

Bosch

Bosch FlexiDomeXT+ VDC-455V03-20 Bedienungsanleitung

Bosch

Bosch VG5 700 Series Bedienungsanleitung

Bosch

Bosch FlexiDomeXF VDC-485V03-20 Bedienungsanleitung

Bosch

Bosch MIC-7522 Bedienungsanleitung

Bosch

Bosch VDC-250 Bedienungsanleitung

Bosch

Bosch AN bullet 2000 IR Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung