Bosch 440 Series Bedienungsanleitung
Analog detectors and bases
440 family detectors and bases
Installation Guide
en english
es español
pt português
th
Analog detectors and bases | 3
Bosch Security Systems, Inc. Installation Guide 2018.08 | 6.0 | F.01U.123.589
en english Table of contents 4
es español Contenido 13
pt português Sumário 23
th สารบัญ 32
4en | Table of contents Analog detectors and bases
2018.08 | 6.0 | F.01U.123.589 Installation Guide Bosch Security Systems, Inc.
Table of contents
1Notes 5
2Product Types 5
3Mounting 6
3.1 Mounting the Detector 6
3.2 Locking and Releasing the Detector 7
4Wiring and Addressing Information 8
4.1 Wiring Information 8
4.2 Addressing Information 9
5Testing the Installation 10
5.1 Magnet Switch Test 10
5.2 Functional Testing 10
6Specifications 11
Analog detectors and bases Notes | en 5
Bosch Security Systems, Inc. Installation Guide 2018.08 | 6.0 | F.01U.123.589
1 Notes
This document covers mounting and wiring for the FAP-440 Series bases and detector heads.
For proper installation, read and understand NFPA-72, The National Fire Alarm Code before
installation.
Notice!
Install the device according to this Installation Guide, NFPA 72, Local Codes and the Authority
Having Jurisdiction (AHJ). Failure to follow these procedures may cause the device to not
function properly. Bosch Security Systems is not responsible for any devices that are
improperly installed.
!
Caution!
Do not paint the detectors. Paint or other foreign matter can prohibit detection.
!
Caution!
Do not remove the dust cap until all onsite construction work has been completed and the
fire panel network has been commissioned.
2 Product Types
Product Type Description
FAP-440 Analog Photoelectric Detector
FAP-440-D Analog Dual-Photoelectric Detector
FAP-440-T Analog Multisensor Detector Photo/Heat
FAP-440-DT Analog Multisensor Detector Dual-Photo/Heat
FAP-440-TC Analog Multicriteria Detector Photo/Heat/CO
FAP-440-DTC Analog Multicriteria Detector Dual-Photo/Heat/CO
FAH-440 Analog Heat Detector, configurable fixed temperature/rate-of-rise
FAA-440-B4 Analog Standard Base 4 inches
FAA-440-B6 Analog Standard Base 6 inches
FAA-440-B4-ISO Analog Isolator Base 4 inches
FAA-440-B6-ISO Analog Isolator Base 6 inches
Table2.1: List of Products
Notice!
The CO sensor detects carbon monoxide as a by-product of combustion. It has not been
evaluated for its ability to detect hazardous CO gas. Do not use the FAP-440-TC and
FAP‑440‑DTC as stand-alone CO detector.
!
Warning!
The FAH-440 heat detectors are not life safety devices.
6en | Mounting Analog detectors and bases
2018.08 | 6.0 | F.01U.123.589 Installation Guide Bosch Security Systems, Inc.
3 Mounting
Notice!
Smoke detectors are not to be used with detector guards unless the combination has been
evaluated and found suitable for that purpose.
– Follow NFPA-72 guidelines for mounting locations. For commercial and industrial
installations, 30ft. (9 m) spacing between smoke detectors is recommended.
– The electrical boxes must be large enough to accommodate the number and size of
conductors as specified by the National Electrical Code or the local Authorities Having
Jurisdiction (AHJ).
3.1 Mounting the Detector
1
2
3
3
3
3
1
1
1
4
Figure3.1: 6-inch and 4-inch Mounting Bases
Position Description
1 Mounting holes
2 Base skirt
3 Release tabs
4 Semicircle notch
1. Mount the base using the two oblong mounting holes (see Position 1).
If you mount the detector with a 6-inch base, first remove the base skirt (2) from the
mounting base using a screwdriver to release the 4 tabs (3).
Analog detectors and bases Mounting | en 7
Bosch Security Systems, Inc. Installation Guide 2018.08 | 6.0 | F.01U.123.589
2. Tighten the base to the mounting surface. Do not over tighten. If you use a 6-inch base, fit
the base skirt onto the mounting base.
3. Turn clockwise until the detector head locks into place and aligns with the semi-circle
notch (4).
3.2 Locking and Releasing the Detector
The detector bases are supplied with a snap-off locking bar (X) as part of the base moulding
to prevent malicious removal of the detector. The locking mechanism is selectable and is
activated by shifting the U-shaped locking bar (X) into the position as shown.
1. Remove the U-shaped locking bar by breaking it from its holder.
2. Tuck it into the opening next to it by pushing hard.
3. Insert the detector head into the base.
XX
Figure3.2: Activating the Locking Mechanism
4. Release the locked detector head by pushing hard through the dimple (O) on the
detector’s outer rim with a screwdriver and at the same time, turning the detector head
to the left.
O
O
Figure3.3: Releasing the Detector
8en | Wiring and Addressing Information Analog detectors and bases
2018.08 | 6.0 | F.01U.123.589 Installation Guide Bosch Security Systems, Inc.
4 Wiring and Addressing Information
4.1 Wiring Information
!
Warning!
Do not twist or loop the wires around the terminals. In and out wires for terminal connection
must be cut, stripped, and inserted as individual ends.
The following wire gauges and maximum line lengths are tested and approved.
– 18 AWG (0.8 mm2) -> 4000 ft. (1200m)
– 16 AWG (1.3 mm2) -> 6225 ft. (1900m)
– 14 AWG (2.1 mm2) -> 7200 ft. (2200m)
– 12 AWG (3.3 mm2) -> 9850 ft. (3000m)
Standard non-twisted, non-shielded wiring (plain old wire) for the SLCs is recommended.
Notice!
Voltage drop calculations along with anticipated wire distance should be considered to
ensure a voltage supply of at least 24 V at every detector.
Terminal Lettering Terminal Function
SC SLC bus - IN/OUT
S SLC bus + IN/OUT
Sin SLC bus + IN
Sout SLC bus + OUT
C Remote output
+
+
S
C
SC
S
C
SC
SC SC
SC
SC
S
S
S
S
Figure4.1: FAA-440-B6/-B4 Standard Base Class B Wiring (Class A Wiring Indicated by Dashed Wire)
Analog detectors and bases Wiring and Addressing Information | en 9
Bosch Security Systems, Inc. Installation Guide 2018.08 | 6.0 | F.01U.123.589
+
+ +
+
Sin
Sout
C
SC
Sin
Sout
C
SC
SC
Sout
Sout
SC
SC SC
Sin
Sout -> Sin
Figure4.2: FAA-440-B6-ISO/-B4-ISO Isolator Base Class B Wiring (Class A Wiring Indicated by Dashed Wire)
DRA-5
DRA-12/24
Sin
CC
S
Figure4.3: Optional Remote Annunciator Wiring, Isolator Base (Left) and Standard Base (Right); SinandS=redwire, C = white
wire
4.2 Addressing Information
The detector’s address is set by positioning three rotary switches located on the back of the
device. Use a flat-bladed screwdriver to position each switch. The switches will click when
turned. The valid address range is 1 to 254.
Hundreds Tens Ones
Tab.4.2: Rotary Switches (e.g. address is 131)
10 en | Testing the Installation Analog detectors and bases
2018.08 | 6.0 | F.01U.123.589 Installation Guide Bosch Security Systems, Inc.
Notice!
Detectors that have no valid address will not be found during the auto-learn. After the
auto‑learn, perform a functional testing for each detector to ensure that all detectors operate
properly.
If the rotary switch address does not match the internal address, please see the panels IOG
for the matching procedure.
5 Testing the Installation
Notice!
Notify all concerned parties before any maintenance or testing of the fire alarm system, and
after completion of these activities.
1. Check the wiring from the control panel to each detector for proper polarity and
continuity.
2. Apply power to the system. Check for alarms and troubles.
3. When the system is alarm free, check each detector to ensure that the LED indicator
flashes green. This verifies the detector is receiving power and operating properly.
Depending on the number of detectors connected, the time between two flashes may be
up to 8 seconds.
5.1 Magnet Switch Test
Holding a magnet at the test point centered over the semicircle notch on the head (see
Figure3.1: 6‑inch and 4‑inch Mounting Bases, Position 4) will cause the LED to flash red. If the
magnet is held at the indicated location for more than 6 seconds, the unit will send an alarm
signal to the panel and the LED will change to steady red until the unit is reset by the panel. If
the magnet is removed before the period of 6 seconds is over, the unit will return to the state
it was in and no alarm signals will be sent. Otherwise, you have to reset the unit.
5.2 Functional Testing
1. Set detectors in walk test mode at the fire panel before testing.
2. Test each detector to ensure it causes a control panel test alarm. After each test, the
alarm is cleared automatically by the control panel within a few seconds, and you can
proceed to the next detector.
Notice!
As soon as the walk test mode is started, a detector test must occur within 25 minutes of the
last test. Otherwise the control panel resets to normal operation.
In walk test mode, the alarm is triggered quicker than during normal operation, allowing for a
faster and more efficient testing.
There are the following options of functional testing:
– either alarm the detector by holding the magnet continuously at the indicated location for
three red flashes (see Magnet Switch Test, page 10), or
– carry out the test procedure(s) depending on the detector type:
Test procedure (Dual-)Photo Heat (Dual-)Photo/Heat (Dual-)Photo/Heat/CO
Aerosol test X X X
Heat source test X X X
Andere Handbücher für 440 Series
1
Dieses Handbuch passt für folgende Modelle
11
Inhaltsverzeichnis
Sprachen:
Andere Bosch Sicherheitssensor Handbücher
Bosch
Bosch ISN-AP1-T Bedienungsanleitung
Bosch
Bosch DS935Z Bedienungsanleitung
Bosch
Bosch RADION PIR C Bedienungsanleitung
Bosch
Bosch ISC-BPQ2-W12 Bedienungsanleitung
Bosch
Bosch FCP-500 Bedienungsanleitung
Bosch
Bosch RF835 Series Bedienungsanleitung
Bosch
Bosch VMD01 M50 PAL Bedienungsanleitung
Bosch
Bosch FCP-320 Series Bedienungsanleitung
Bosch
Bosch D-tect 150 Professional Bedienungsanleitung
Bosch
Bosch DS1109i Bedienungsanleitung
Bosch
Bosch GMS 120 Professional Bedienungsanleitung
Bosch
Bosch MS-LZS Bedienungsanleitung
Bosch
Bosch FCP-O 500 Bedienungsanleitung
Bosch
Bosch ISN?SM?80 Bedienungsanleitung
Bosch
Bosch 520 Series Bedienungsanleitung
Bosch
Bosch IR LD 1.0 Bedienungsanleitung
Bosch
Bosch MX934i Bedienungsanleitung
Bosch
Bosch DS840LSN Bedienungsanleitung
Bosch
Bosch ISA-WM-869 Bedienungsanleitung
Bosch
Bosch ISC-BPR2-W12 Bedienungsanleitung
Beliebte Sicherheitssensor Handbücher anderer Marken
Challenger
Challenger SL01 Bedienungsanleitung
DMP Electronics
DMP Electronics 1122INT Bedienungsanleitung
Rielta
Rielta Ladoga MK-RK Bedienungsanleitung
Mirion Technologies
Mirion Technologies ACCURAD PRD Bedienungsanleitung
DBI SALA
DBI SALA EZ Stop Bedienerhandbuch
Lamptime
Lamptime ST05C Bedienungsanleitung
