Bosch Room thermostat II Bedienerhandbuch

Room thermostat II

quick instructions

Product description

The room thermostat II measures the temperature at

a suitable location in the room and ensures a more

stable and eﬃcient temperature control. It is the per-

fect complement to your Bosch Smart Home radia-

tor thermostats.

Description of the symbols

Warning!

Note about hazards

Note:

Additional

important information

Note about the installation video

8-750-002-423

Safety instructions

▶ Read this user manual completely before installing

or commissioning the device and pay particular

attention to the hazard information.

▶ Do not charge used batteries, and do not attempt

to reactivate them using heat or other means. Do

not short-circuit batteries. Do not expose batteries

to strong sunlight. Do not throw batteries into fire!

There is a risk of explosion!There is a risk of explosion!

▶ Make sure the polarity is correct when insert-

ing the batteries! Only use batteries of the same

type. Drained batteries must be removed from the

device immediately. Remove batteries from the

device if it is not in use for a long period of time.

Increased risk of leakage!Increased risk of leakage!

▶ Store small cells and batteries which could be

swallowed out of the reach of children. Swallowing

can result in burns, perforation of the soft tissue

and death. Severe burns can occur within 2 hours

after swallowing. In the event that a cell or battery

is swallowed, seek medical assistance immedi-

ately.

▶ The device is not a toy! Do not allow children to

play with it. Never leave the packaging material

lying around unattended. Plastic ﬁlm and small

parts may pose a danger to children.

▶ This device may be used by children from 8 years

of age and by persons with reduced physical, sen-

sory or mental capacities, or a lack of experience

and knowledge provided these persons are super-

vised or have been instructed in the safe use of the

device, and understand the corresponding risks.

▶ When remotely or automatically controlling a

device, it is not always possible to guarantee that

commands are actually executed or that the cor-

rect device status is displayed in the app and on

other Smart Home display devices because of

external circumstances. This may lead to mate-

rial damage and/or personal injury. Therefore, you

must ensure to the greatest extent possible that no

person is endangered at the time of remote opera-

tion or automated control. Please take special care

when setting up or adjusting the remote control or

when using the automated control and check the

desired functionality at regular intervals.

▶ Do not open up the device. It does not contain

any parts to be maintained by the user. If a fault

occurs, have the device checked by a specialist.

▶ We accept no liability for material damage or per-

sonal injury which is caused by improper use or

failure to observe the safety instructions. In these

cases, any guarantee claim becomes void! We

accept no liability for consequential damage.

▶ For safety and approval reasons (CE/UKCA), the

device may not be modiﬁed and/or no changes

may be made to the device without authorisation.

▶ Do not paint over the device! Do not apply wallpa-

per over the device!

▶ Any use other than that which is described in the

user manual is considered improper and leads to

the exclusion of guarantee and liability.

▶ Do not use the device if it has damage visible from

the outside, for example, to the housing, control

elements or connection sockets, or if it has a mal-

function. If in doubt, please contact our service

team.

▶ Only operate the device indoors and do not expose

it to moisture, vibrations, constant sunlight or

other sources of heat, extreme cold temperatures

and mechanical stress.

▶ Only use the device together with original com-

ponents and recommended products from Bosch

partners.

Notes

▶ The range within buildings can diﬀer signiﬁcantly

from the range in open spaces. In addition to the

transmitting power and the receiving properties of

the receiver, environmental factors such as humid-

ity, as well as the local structural situation, play an

important role.

▶ The device is only intended for use in residential

environments.

▶ The device is only intended for private use.

You can also use the explanatory videos and

additional information on our website as an

additional aid for mounting, installing, starting

up and restoring the factory settings on your

Bosch Smart Home room thermostat II:

www.bosch-smarthome.com/rom/

room-thermostat-2

Product overview

5 9

Item Name Explanation

1Device front view

2LED display

3Status LED

4Rotary knob/system

button

5Device rear view

6Sensor connection Connection for op-

tional accessories.

7Mounting bracket

receiving openings

For diﬀerent angles

of inclination of the

device.

8Battery compart-

ment

Ensure correct po-

larity when inserting

the batteries!

9Mounting plate Used to attach the

device to the wall.

10 Mounting bracket

Used to install the

device on even

surfaces.

LED display (2)

Item Name Description

aInformation area Displays error codes or other additional informa-

tion.

bHumidity Displays room humidity in normal operation.

cStatus indicators

Battery status Appears with low battery charge

Connection status Wireless connection to the controller is active. In

the event of constant ﬂashing, there is a connection

problem with the controller.

Child lock Press the system button >3 seconds, adjust the

desired value by turning

Open window The system has detected an open window in the

room. Heating/cooling mode paused.

dCooling mode The device/system is set to cooling mode.

eHeating mode The device/system is set to heating mode.

fRoom control modes

(press system button 1x, select mode)

Automatic Room control is controlled via a schedule.

Manual Temperature at constant value. Can be changed via

rotary knob.

Heating break The regulation in the room pauses.

gValue display Displays actual and set temperature. Other text

information in case of an error or during conﬁgura-

tion.

The status LED (3) shows the status of the room ther-

mostat using ﬂashing codes.

Signal Meaning Measures

Flashes

orange

Pairing mode (is

active) or device

is communicat-

ing with the

controller

Please wait

Flashes

green

Pairing mode

(successful)

or process

conﬁrmed

Flashes

red 1x

Pairing mode

(not successful)

process failed

If this is the ﬁrst tun-

ing attempt, please

try again. Otherwise

reset the device to

the factory settings

and contact the

service department if

necessary.

Flashes

red

every

15 sec-

onds

Functional error Look for informa-

tion in the Smart

Home app. Contact

the service team if

necessary.

Notes regarding installation

When selecting the mounting location and when

drilling, pay attention to the areas where elec-

trical wires run, or to any supply cables.

Start-up

Ensure that you have a Bosch Smart Home control-

ler and the Bosch Smart Home app and have suc-

cessfully conﬁgured both. Now start the Bosch Smart

Home app and select “Add new device”. Follow the

instructions in the app.

Resetting to factory settings

You can reset the device to its factory settings as

follows:

Open the battery compartment (8) and remove one

of the batteries. Replace the battery while holding the

rotary knob (4) pressed. Hold the knob pressed until

the status LED (3) on the room thermostat ﬂashes

orange and “RES” appears on the display. Now

release it brieﬂy and press the knob again and hold

until the LED lights green. The device then restarts.

Please note that it can take a few seconds until the

room thermostat is ready for operation again.

When resetting to factory settings, the settings

and information are only lost from the device

and not from the Bosch Smart Home controller.

To re-configure the device, first delete it in the

device management section of the Bosch Smart

Home app and then add it again in the usual

configuring process.

Maintenance and cleaning

Removing or changing the batteryRemoving or changing the battery

To remove or replace the batteries, remove the

device from the mounting plate (9) or ﬁrst remove the

mounting bracket (10). Open the battery compart-

ment(8). Remove the batteries. Take care to ensure

the correct polarity when replacing them.

The device does not require maintenance. Leave any

repairs to a specialist. Clean the device with a soft,

clean, dry and lint-free cloth. When cleaning, do not

use any cleaning agents containing solvents.

Simpliﬁed declaration of conformity

Robert Bosch Smart Home GmbH hereby

declare that the radio equipment type Bosch

Smart Home BTH-RM corresponds with the directive

2014/53/EU. The complete text of the EU declaration

of conformity is available via the following web

address: https://eu-doc.bosch.com

Robert Bosch Smart Home GmbH hereby

declares that the radio system type BTH-RM

complies with Regulation 2017. The full text of

the declaration of conformity is available at the

following internet address: https://gb-doc.bosch.com

Environmental protection and disposal

Electrical or electronic devices which are no

longer usable must be collected separately

and disposed of via an environmentally

friendly recycling facility (European Directive on

Waste Electrical and Electronic Equipment). Use your

country’s speciﬁc return and collection systems when

disposing of waste electrical or electronic devices.

Used batteries do not go in the household

waste! Dispose of them at your local battery

collection point!

Inhaltsverzeichnis

Andere Bosch Thermostat Handbücher

Bosch

Bosch FR 10 Bedienungsanleitung

Bosch

Bosch TSTBT4H2CP-M--A Bedienungsanleitung

Bosch

Bosch TSTBM3H2CPH6W-A Bedienungsanleitung

Bosch

Bosch BCC100 Service-Handbuch

Bosch

Bosch OR80 OT Bedienungsanleitung

Bosch

Bosch FW 100 Bedienungsanleitung

Bosch

Bosch EasyControl CT200 Bedienungsanleitung

Bosch

Bosch FR 10 Montageanleitung

Bosch

Bosch BCC100 Bedienungsanleitung

Bosch

Bosch Smart Home Thermostat AA Bedienungsanleitung

Bosch

Bosch TSTBM-RRS--TW-A Bedienungsanleitung

Bosch

Bosch Room thermostat II 230 V Bedienerhandbuch

Bosch

Bosch DT1 Bedienungsanleitung

Bosch

Bosch TRZ 12-2 Bedienungsanleitung

Bosch

Bosch FR 10 Bedienungsanleitung

Bosch

Bosch TRZ 12-2 Bedienungsanleitung

Bosch

Bosch CRC R-1 Bedienungsanleitung

Bosch

Bosch 8-733-944-325 Leitfaden

Bosch

Bosch Worcester Greenstar Comfort II RF Bedienungsanleitung

Bosch

Bosch BCC100 Montageanleitung

Bosch

Bosch MT 10 Bedienungsanleitung

Bosch

Bosch CR 20 RF Bedienungsanleitung

Bosch

Bosch TR 200 Bedienungsanleitung

Bosch

Bosch BCC100 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung