Bosch BCC100 Bedienungsanleitung

BoschHeatingAndCooling.com

Bosch Connected Control

BCC100 Wi-Fi Thermostat User Guide

Contents

WARNING: Failure

to follow and read

all instructions

before installing or

operating this device

may cause personal

injury and/or

property damage.

IN THE BOX:

▶BCC100 Wi-Fi Thermostat

▶Screws (2) and Anchors (2)

▶Flathead Screwdriver

▶Wire Labels

▶Jumper Wire

▶User Guide

▶Customer Support Card

Some features require an

internet connection and a

user account. Features,

speciﬁcations, and

appearance are subject to

change without notice.

A C-wire (common wire) is

required to power the unit.

Two wire systems are not

supported. If a C-wire is not

available, please contact

your local Contractor for

support.

CHECK COMPATIBILITY FIRST

For conventional (gas/oil/electric) ▶Heat Only, Cool Only,

and Combined Heat & Cool

For heat-pump systems ▶Up To 4-Heat & 2-Cool

Not compatible with other Bosch Boiler controls, such as the Logamatic

Getting Started.......................2

Main Screen............................9

Icons.....................................10

Initialization..........................12

Wi-Fi Setup...........................16

App Setup.............................19

Starting Your System............21

Temporary Scheduling..........23

Programming Schedules.......24

Additional Features

...............

Advanced Features...............30

Warranty

...............................

Connected Solution for 24VAC Thermostat Systems

Getting Started

The BCC100 thermostat is designed to work on most 24VAC

low voltage heating and cooling systems such as gas and oil

furnaces, heat pumps, and single or dual-stage systems.

Professional installation recommended for:

▶Humidiﬁers and dehumidiﬁers

Before removing the wires from the old thermostat, take a

picture of the wiring conﬁguration for reference, and then

label each wire according to the terminal codes using the

wire labels provided.

Remove the Old Thermostat

NOTE: After labeling the wires, secure them to an

object such as a pen or clip to prevent them from

falling back into the wall.

WARNING: Turn Oﬀ Power

Failure to turn oﬀ power may result in

electrical shock and/or system damage.

Disconnect the wires from the old thermostat one by

one. Do not let wires fall back into the wall.

Turn Oﬀ Power

Please turn oﬀ the unit’s main power at the circuit panel

before beginning the installation process.

Feed all wires vertically into the hole or slit in the center

of the backplate. Referencing the photo of the previous

wiring conﬁguration or the wire labels currently on the

wires, insert the wires one-by-one into the matching

terminals, and use the supplied ﬂathead screwdriver to

close each terminal. After you have ﬁnished fastening the

wires, pull each wire gently to ensure they are secure.

Repeat this process for each wire to be installed.

Connect the New Wall Plate

CAUTION: To prevent possible shorts to adjacent

terminals, use care when securing and routing

your thermostat wires.

Mount the New Wall Plate

Use the enclosed screws and anchors to

mount the new wall plate. In most cases,

you can utilize the same mounting position of your old

thermostat. Be sure to check the alignment of your wall

plate before installation to ensure all holes are covered.

Note: The color of your wires may not be the same as shown in this User Guide

(1)Emergency heat activated at W1, (2)Auxiliary heat activated at W2,

(3)Only to be used with Bosch WSHP)

BCC100 Terminal Key

Data

Alarm Input3

Common

W/E (W1)

1st Stage Heating1

Y (Y1)

1st Stage Compressor

Heating Appliance Power

RC (R)

Cooling Appliance Power

----

Not Used

Fan

(W2) 2nd Stage Heating2

2nd Stage Compressor

O/B

Reversing Valve

H/DH

Humidiﬁer/Dehumidiﬁer

Jumper

Conventional Systems

Conventional systems include furnaces, boilers, and

dedicated, non-window air conditioning units.

NOTE: The following wiring diagrams describe some

common conﬁgurations that are compatible with the

BCC100. Not all compatible conﬁgurations are depicted

below. If you are unsure of how to connect your

thermostat, please contact customer support using the

number on the card provided in the box.

Single Stage Heat – Boiler

Ensure the system has a C-wire

Ensure the pre-installed jumper

wire remains between RH and RC

Connect the R, C and W1 wires

from the boiler to RH, C and W/E

terminals on the wall plate,

respectively

Jumper

----

O/B

H/DH

Data

W/E

Single Stage Heat – Furnace

Ensure the system has a C-wire

Ensure the pre-installed jumper

wire remains between RH and RC

Connect the R, C, W1 and G

wires from the Furnace to RH, C,

Y and G terminals on the wall

plate, respectively

Jumper

----

O/B

H/DH

Data

W/E

Two Stage Heat – Furnance

Ensure the system has a C-wire

Ensure the pre-installed jumper

wire remains between RH and RC

Connect the R, C, W1, W2 and G

wires from the Furnace to RH, C,

W/E, W2 and G terminals on the

wall plate, respectively

Jumper

----

O/B

H/DH

Data

W/E

Combined Single Stage Heat and Cool

Furnace and Air Conditioner ONLY

Note: combined boiler and air conditioner

systems are not currently supported.

Ensure the system has a C-wire

Remove the pre-installed jumper

wire from between RH and RC

Connect the R, C, W1 and G wires

from the Furnace to RH, C, W/E

and G terminals on the wall plate,

respectively

Connect the R, C, Y1 and G wires

from the Air Conditioner to RC, C,

Y and G terminals on the wall plate,

respectively

----

O/B

H/DH

Data

W/E

Single Stage Cool – Air Conditioner

Ensure the system has a C-wire

Ensure the pre-installed jumper

wire remains between RH and RC

Connect the R, C, Y1 and G wires

from the Air Conditioner to RC,

C, Y and G terminals on the wall

plate, respectively

Jumper

----

O/B

H/DH

Data

W/E

Single Stage Heat Pump

Ensure the system has a C-wire

Ensure the pre-installed jumper

wire remains between RH and RC

Connect the R, C, Y1, O/B and G

wires from the heat pump to RC,

C, Y, O/B and G terminals on the

wall plate, respectively

Jumper

----

O/B

H/DH

Data

W/E

Heat Pump Systems

Heat pump systems are specialty designed to be able to

provide heating and cooling using a single compressor, a

reversing valve, and a fan

Single Stage Heat Pump with

Emergency Heat and Auxiliary Heat

Note: W/E controls the Emergency Heat

output and W2 controls the Auxiliary Heat

output. Therefore, a jumper is required when

using the same heating source for both

Emergency Heat and Auxiliary Heat.

Ensure the system has a C-wire

Ensure the pre-installed jumper

wire remains between RH and RC

Connect the R, C, W1, Y1, O/B and

G wires from the heat pump to RC,

C, W/E, Y, O/B and G terminals on

the wall plate, respectively

Connect the supplied jumper

wire between the W/E and W2

terminals of the wall plate

Jumper

----

O/B

H/DH

Data

W/E

Two Stage Heat Pump with

One Stage Emergency Heat

Ensure the system has a C-wire

Ensure the pre-installed jumper

wire remains between RH and RC

Connect the R, C, W1, Y1, Y2,

O/B and G wires from the heat

pump to RC, C, W/E, Y, Y2, O/B

and G terminals on the wall plate,

respectively

Jumper

----

O/B

H/DH

Data

W/E

Humidiﬁer or Dehumidiﬁer

Accessory with a Combined Single

Stage Heat and Cool Conventional

System

Note: The wiring conﬁguration for

humidiﬁers and dehumidiﬁers is the same

for all type of Conventional Systems.

Ensure that the accessory is

externally powered

Ensure the Conventional System

is wired correctly

Connect the control wire of the

accessory to the H/DH terminal

of the wall plate

----

O/B

H/DH

Data

W/E

Humidiﬁer and Dehumidiﬁer Accessory

A single Humidiﬁer or Dehumidiﬁer Accessory can be

controlled using the BCC100. The thermostat only

supports Humidiﬁers in heating operation, Dehumidiﬁers

in cooling operation, and only one accessory per

thermostat.

Humidiﬁer or Dehumidiﬁer

Accessory with a Single Stage

Heat Pump

Note: The wiring conﬁguration for

humidiﬁers and dehumidiﬁers is the same

for all type of Heat Pump Systems

Ensure that the accessory is

externally powered

Ensure the Heat Pump System is

wired correctly

Connect the control wire of the

accessory to the H/DH terminal

of the wall plate

Jumper

----

O/B

H/DH

Data

W/E

Attach BCC100 to the Wall Plate

Align the two clips on

the back of the

BCC100 into the

corresponding slots

on the top of the

wall plate.

Firmly press forward

until you hear a click to

secure the thermostat

into position.

PUSH

CLIPS

Switch on the power to the heating/cooling system at the

main switch box. If the thermostat does not power on,

remove the BCC100 from the wall and ensure the RH/RC

wire(s) and C-wire are correctly connected to both the

appliance and the thermostat.

When your thermostat powers on, it prompts you to

start the setup. If you are having trouble powering the

thermostat, please refer to the Customer Support

Card in the box for additional support information.

Thank you for choosing the BCC100. Enjoy the savings

and comfort of owning a Bosch connected thermostat!

Main Screen

System

Mode

Main Menu Fan

Status Wiﬁ / Cloud Access

Indicator

Current

Room

Humidity Current Room

Temperature

Current

Schedule

Adjust

Temperature

Set-Points

Enjoy the experience

of the product!

Andere Handbücher für BCC100

Inhaltsverzeichnis

Andere Bosch Thermostat Handbücher

Bosch

Bosch TRZ 12-2 Bedienungsanleitung

Bosch

Bosch FR 10 Bedienungsanleitung

Bosch

Bosch Climate 5000 Series Bedienungsanleitung

Bosch

Bosch Worcester Easy control Bedienungsanleitung

Bosch

Bosch 3H/2C Leitfaden

Bosch

Bosch Worcester Greenstar Comfort II RF Bedienungsanleitung

Bosch

Bosch EasyControl Bedienungsanleitung

Bosch

Bosch BCC50 Montageanleitung

Bosch

Bosch BMS-WT1 Series Bedienungsanleitung

Bosch

Bosch TR 200 Bedienungsanleitung

Bosch

Bosch BCC50 Bedienungsanleitung

Bosch

Bosch OR80 OT Bedienungsanleitung

Bosch

Bosch Room thermostat II Bedienerhandbuch

Bosch

Bosch TRZ 12 T Bedienungsanleitung

Bosch

Bosch Room thermostat II 230 V Bedienerhandbuch

Bosch

Bosch BCC100 Bedienungsanleitung

Bosch

Bosch TRZ 12-2 Bedienungsanleitung

Bosch

Bosch EasyControl CT200 Bedienungsanleitung

Bosch

Bosch Smart Home Thermostat AA Bedienungsanleitung

Bosch

Bosch CR 50 Bedienungsanleitung

Bosch

Bosch TSTBM3H2CPH6W-A Bedienungsanleitung

Bosch

Bosch CR 50 Bedienungsanleitung

Bosch

Bosch RT10-RF Bedienungsanleitung

Bosch

Bosch TSTBM-RRS--TW-A Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung