Bosch VPV 16 Installations- und Betriebsanleitung

Hydraulics

VPV Vane Pump

Service and Repair Guide

VPV Vane Pump 1

Table of Contents

Introduction 2

Benefits 2

Specifications 3

Ordering Guide 6

Performance Characteristics 9

Performance Characteristics - VPV 16 to 3000 PSI (210 Bar) 10

Performance Characteristics - VPV 25 to 3000 PSI (210 Bar) 12

Performance Characteristics - VPV 32 to 3000 PSI (210 Bar) 14

Performance Characteristics - VPV 45 to 3000 PSI (210 Bar) 16

Performance Characteristics - VPV 63 to 3000 PSI (210 Bar) 18

Performance Characteristics - VPV 80 to 3000 PSI (210 Bar) 20

Performance Characteristics - VPV 100 to 3000 PSI (210 Bar) 22

Performance Characteristics - VPV 130 to 3000 PSI (210 Bar) 24

Performance Characteristics - VPV 164 to 3000 PSI (210 Bar) 26

VPV 16, Single pump, S.A.E. ‘A’ flange, RH rotation, Installation Drawing 28

VPV 16, Single pump, Metric flange, RH rotation, Installation Drawing 29

VPV 25/32, Single pump, S.A.E. ‘B’ flange, RH rotation, Installation Drawing 30

VPV 25/32, Single pump, Metric flange, RH rotation, Installation Drawing 31

VPV 25/32, Single pump, S.A.E. ‘B’ flange, RH rotation, Installation Drawing 32

VPV 25/32, Single pump, S.A.E. ‘B’ flange, w/ solenoid 2-pressure compensator, Inst. Drw. 33

VPV 25/32, Single pump, S.A.E. ‘B’ flange, w/ NG6 pilot valve, Installation Drawing 34

VPV 45/63/80, Single pump, S.A.E. ‘C’ flange, RH rotation, Installation Drawing 35

VPV 45/63/80, Single pump, Metric flange, RH rotation, Installation Drawing 37

VPV 100/130/164, Single pump, S.A.E. ‘D’ flange, RH rotation, Installation Drawing 39

VPV 100/130/164, Single pump, Metric flange, RH rotation, Installation Drawing 41

VPV 16, Combination pump, S.A.E. ‘A’ flange, RH rotation, Installation Drawing 43

VPV 25/32, Combination pump, S.A.E. ‘B’ flange, RH rotation, Installation Drawing 44

VPV 32/16, Combination pump, S.A.E. ‘B’ flange, RH rotation, Installation Drawing 45

VPV 32/25, Combination pump, S.A.E. ‘F’ Gear pump, RH rotation, Installation Drawing 46

VPV 45/63/80 to VPV 16, S.A.E. & Metric Combination, Installation Drawing 47

VPV 45/63/80 to VPV 25/32, S.A.E. & Metric Combination, Installation Drawing 50

VPV 45/63/80 to an ‘F’ Gear pump, S.A.E. & Metric Combination, Installation Drawing 53

VPV 45/63/80 to an ‘G’ Gear pump, S.A.E. & Metric Combination, Installation Drawing 56

VPV 45/63/80 to VPV 45/63/80, S.A.E. & Metric Combination, Installation Drawing 58

VPV 100/130/164 to VPV 100/130/164 S.A.E. & Metric Combination, Installation Drawing 62

VPV 100/130/164 to VPV 16 S.A.E. & Metric Combination, Installation Drawing 64

VPV 100/130/164 to VPV 25/32 S.A.E. & Metric Combination, Installation Drawing 67

VPV 100/130/164 to VPV 45/63/80 S.A.E. & Metric Combination, Installation Drawing 70

VPV 100/130/164 to ‘F’ Gear pump, S.A.E. & Metric Combination, Installation Drawing 73

VPV Controls 77

Comparison of Sound Levels 79

Trouble Shooting 80

Adapter Kits for VPV Combinations Using P1 Pumps 81

Through Drive Horsepower Limitations 82

VPV Stroke Limiter Adjustment 83

2000 PSI Repair Parts 84

3000 PSI Repair Parts 90

Vane Tip Orientation 95

VPV Tool Kit 96

Reaction Characteristics and Shock Clipper Function 97

2VPV Vane Pump

Introduction

Benefits

This catalog introduces a new line of enhanced performance variable displacement pressure compensated vane

pumps from Bosch.

The pumps are designed to meet the requirements of the machine tool, general machinery, and other markets where

low noise, high performance and competitive pricing are needed.

The design of the VPV series of vane pumps utilizes 30 years of field and manufacturing experience from the current

Bosch vane pump line. State-of-the-art technologies and materials were utilized while retaining the superior features

of the existing designs. Additional goals were to create a pump with the international market in mind and to incorpo-

rate the extremely high quality standards the Bosch name has come to exemplify.

Keeping in mind market expectations, Bosch developed a pump with the following improvements and features:

1. High reliability with fewer parts.

2. Significant advances in noise reduction.

3. High volumetric and overall efficiency.

4. Excellent durability.

5. Modern appearance.

6. Improved ring and vane wear technology.

7. Very good response and recovery times.

8. Generally reduced envelope size.

9. Redesigned controls with shock clipper.

10. Conforms to the latest SAE, ISO, NFPA, and ANSI standards.

11. Combination capability - full horsepower may be transferred to pump 2. Combinations of construction of

multiple pumps may be required to be de-rated.

• LOW COST - Competitively priced with other manufacturers of vane pumps and economy axial piston pumps.

• EXCEPTIONALLY QUIET - Helps machinery builders meet government and purchased sound level requirements.

• CONTINUOUS DUTY RATING - @ 3,000 PSI - High performance and long life design for 10,000 plus hours.

• HIGHLY EFFICIENT FAST RESPONSE & RECOVERY - Exceptional reaction time for critical system demands.

• PRESSURE COMPENSATED - Controls pump delivery to circuit demand thereby conserving energy.

• HIGH STRENGTH - Computer optimized casting design.

• HYDRODYNAMIC JOURNAL BEARINGS - Provides long life and quiet operation.

• NO PREFILL REQUIREMENTS - Pump case prefill not required for initial start-ups.

• REPAIRABLE - Repair kits and parts available from local distribution centers or the factory.

• CONTROL OPTIONS - Single stage; two-stage, remote control; solenoid multi-pressure; load sensing; solenoid;

torque limiting and elecronic proportional.

• SHOCK CLIPPER - Reduces shock pressure by up to 50% increasing system component life and system stability.

Must be plumbed on VPV 16, 25, & 32. The shock clipper is integrated into VPV 45, 63, 80, 100,

130, & 164 and drains to the case drain. See page 97.

VPV Vane Pump 3

Specifications

General VPV 16 VPV 25 VPV 32

Displacement (Nominal) 1 in3/rev (16 cm3/rev) 1.5 in3/rev (25 cm3

rev) 2 in3 /rev (32 cm3

/rev)

Displacement (Actual) 1.06 in3

/rev (16.8 cm3/rev) 1.66 in3

/rev (27.4 cm3

rev) 2.04 in3/rev (32 cm3

/rev)

Flow at 1750 RPM17.57 GPM (28.6 L/min) 11.36 GPM (43.0 L/min) 15.15 GPM (57.3 L/min)

Maximum continuous pressure 3000 psi (210 bar)

Pressure compensating Single stage 200-3000 psi (14-210 bar) Minimum pressure of 190 PSI

range Two stage 300-3000 psi (20-210 bar) Minimum pressure of 290 PSI

Maximum transient spike pressure 3800 psi (260 bar) 4000 psi (280 bar)

Maximum case pressure 10 psi (0.7 bar)

Speed range 1150-1800 RPM

Direction of rotation (viewed from shaft end) Right hand (clockwise)

Case drain flow 1000 psi (70 bar) 0.6 GPM (2.3 L/min) 0.6 GPM (2.3 L/min)

while compensating 2000 psi (140 bar) 0.9 GPM (3.4 L/min) 1.1 GPM (4.2 L/min)

@ 1800 RPM 3000 psi (210 bar) 1.26 GPM (4.8 L/min 1.4 GPM (5.3 L/min)

Maximum inlet vacuum at sea level 6 in. HG (152 mm HG)

Mounting2- SAE 2-bolt flange (ISO 3019/1) S.A.E. ‘A’ S.A.E. ‘B’

2-bolt flange 2-bolt flange

Mounting Position Unrestricted

Inlet #16 S.A.E. #24 S.A.E

Outlet #12 S.A.E. #16 S.A.E.

Port sizes Case drain #8 S.A.E.

Clipper control drain (optional) #6 S.A.E.

Remote control (optional) #4 S.A.E.

Drive Pump to be connected to prime mover by means of a flexible coupling that is aligned

to a maximum of .006” (.152mm) total indicator reading. No overhung or side loads

permitted. Alignments greater than .006” indicator reading could cause increased

noise and vibration as well as premature shaft seal wear resulting in leakage.

Fluid recommendations A premium quality hydraulic oil with anti-wear additives is recommended, but not

required. Refer to publication S-106 “Petroleum Hydraulic Fluids” for a list of fluids

which meet or exceed the necessary lubrication requirements. Consult factory for

use with water base fire resistant fluids.

Minimum 100 SUS (21 cSt)

Fluid viscosity at Maximum 1000 SUS (216 cSt)

operating temperature Optimum 150-250 SUS (32-54 cSt)

Maximum start-up 4000 SUS (864 cSt)

Fluid temperature Normal inlet fluid temperature should not exceed 140°F (60° C). Always select a fluid

for optimum viscosity at operating temperature. Consult factory for applications assis-

tance when inlet fluid temperatures over 140° F (60° C) are expected.

Seals Fluorocarbon Standard

Filtration Fluid cleanliness per ISO/DIS 4406 should be 18/15 or better for pressures of 2000 psi or

less. For continuous operating pressures of 2000 to 3000 psi, fluid cleanliness should be

17/13 or better.

Response time Full flow to 20-35 ms 20-35 ms

(circuit dependent) minimum flow

Recovery time Minimum flow 50-135 ms – 70-185 ms –

(circuit dependent) to full flow single stage compensator single stage compensator

Weight Single stage 34 lbs. (16.5 kg) 61 lbs. (28 kg)

Two stage 38 lbs. (17.3 kg) 65 lbs. (28.5 kg)

1Flows are actual. Volumetric efficiencies shown in technical data taken into account.

2Metric

4-bolt flange

available

(ISO 3019/2)

available. Please consult factory.

4VPV Vane Pump

Specifications

General VPV 45 VPV 63 VPV 80

Displacement (Nominal) 2.75 in3

/rev (45 cm3/rev) 3.84 in3

/rev (63 cm3

rev) 4.88 in3/rev (80 cm3

/rev)

Displacement (Actual) 2.88 in3

/rev (47.3 cm3/rev) 3.93 in3

/rev (64.4 cm3

rev) 5.02 in3/rev (82.3 cm3

/rev)

Flow at 1750 RPM120.83 GPM (72.84 L/min) 29.10 GPM (110.1 L/min) 36.97 GPM (139.9 L/min)

Maximum continuous pressure 3000 psi (210 bar)

Pressure compensating range Two stage 350-3000 psi (24-210 bar) Minimum pressure of 300 PSI

Maximum transient spike pressure 4000 psi (280 bar)

Maximum case pressure 10 psi (0.7 bar)

Speed range 1150-1800 RPM

Direction of rotation (viewed from shaft end) Right hand (clockwise)

Case drain flow 1000 psi (70 bar) 1.5 GPM (5.7 L/min) 1.4 GPM (5.3 L/min) 1.4 GPM (5.3 L/min)

while compensating 2000 psi (140 bar) 1.9 GPM (7.2 L/min) 1.8 GPM (6.8 L/min) 1.8 GPM (6.8 L/min)

@ 1800 RPM 3000 psi (210 bar) 2.5 GPM (9.5 L/min) 2.4 GPM (9.1 L/min) 2.3 GPM (8.7 L/min)

Maximum inlet vacuum at sea level 6 in. HG (152 mm HG)

Mounting2- SAE 2-bolt flange (ISO 3019/1) S.A.E. ‘C’ 2-Bolt flange

Mounting Position Unrestricted

Inlet 2” S.A.E.

Outlet 1 1/4” S.A.E. flange

Port sizes Case drain S.A.E. = #8 S.A.E.

Remote control (optional) S.A.E. = #4 S.A.E.

Drive Pump to be connected to prime mover by means of a flexible coupling that is aligned

to a maximum of .006” (.152mm) total indicator reading. No overhung or side loads

permitted. Alignments greater than .006” indicator reading could cause increased

noise and vibration as well as premature shaft seal wear resulting in leakage.

Fluid recommendations A premium quality hydraulic oil with anti-wear additives is recommended, but not

required. Refer to publication S-106 “Petroleum Hydraulic Fluids” for a list of fluids

which meet or exceed the necessary lubrication requirements. Consult factory for

use with water base fire resistant fluids.

Minimum 150 SUS (32 cSt)

Fluid viscosity at Maximum 1000 SUS (216 cSt)

operating temperature Optimum 200-300 SUS (43-65 cSt)

Maximum start-up 4000 SUS (864 cSt)

Fluid temperature Normal inlet fluid temperature should not exceed 140°F (60° C). Always select a fluid

for optimum viscosity at operating temperature. Consult factory for applications assis-

tance when inlet fluid temperatures over 140° F (60° C) are expected.

Seals Fluorocarbon Standard

Filtration Fluid cleanliness per ISO/DIS 4406 should be 18/15 or better for pressures of 2000 psi or

less. For continuous operating pressures of 2000 to 3000 psi, fluid cleanliness should be

17/13 or better.

Response time Full flow to 20-40 ms

(circuit dependent) minimum flow

Recovery time Minimum flow 100-250 ms – two stage compensator

(circuit dependent) to full flow

Weight Single stage 120 lbs. (55 kg)

Two stage 128 lbs. (58 kg)

1Flows are actual. Volumetric efficiencies shown in technical data taken into account.

2Metric

4-bolt flange

available

(ISO 3019/2)

available. Please consult factory.

VPV Vane Pump 5

Specifications

General VPV 100 VPV 130 VPV 164

Displacement (Nominal) 6.1 in3

/rev (100 cm3/rev) 7.9 in3

/rev (130 cm3

rev) 10.0 in3/rev (164 cm3/rev)

Displacement (Actual) 6.0 in3

/rev (99 cm3 /rev) 8.0 in3

/rev (131 cm3

rev) 10.0 in3/rev (164 cm3/rev)

Flow at 1750 RPM145.4 GPM (171.8 L/min) 59.85 GPM (226.5 L/min) 75.76 GPM (286.7 L/min)

Maximum continuous pressure 3000 psi (210 bar) 3000 psi (210 bar)

Pressure compensating Two stage 350-3000 psi (24-210 bar) 350-3000 psi (24-210 bar)

Maximum transient spike pressure 4000 psi (280 bar) 4000 psi (280 bar)

Maximum case pressure 10 psi (0.7 bar)

Speed range 1150-1800 RPM

Direction of rotation (viewed from shaft end) Right hand (clockwise)

Case drain flow 1000 psi (70 bar) 1.5 GPM (5.7 L/min) 1.6 GPM (6.0 L/min) 1.7 GPM (6.4 L/min)

while compensating 2000 psi (140 bar) 2.0 GPM (7.6 L/min) 2.2 GPM (8.3 L/min) 2.3 GPM (8.7 L/min)

@1800 RPM 3000 psi (210 bar) 2.5 GPM (9.5 L/min) 3.0 GPM (11.3 L/min) 3.1 GPM (11.7 L/min)

Maximum inlet vacuum at sea level 6 in. HG (152 mm HG)

Mounting2- SAE 2-bolt flange (ISO 3019/1) S.A.E. ‘D’, 2-bolt flange

Mounting Position Unrestricted

Inlet 2 1/2” S.A.E.

Outlet 1 1/2” S.A.E.

Port sizes Case drain S.A.E. = #8 S.A.E.

Remote control (optional) #4 S.A.E.

Drive Pump to be connected to prime mover by means of a flexible coupling that is aligned

to a maximum of .006” (.152mm) total indicator reading. No overhung or side loads

permitted. Alignments greater than .006” indicator reading could cause increased

noise and vibration as well as premature shaft seal wear resulting in leakage.

Fluid recommendations A premium quality hydraulic oil with anti-wear additives is required*. Refer to publica-

tion S-106 “Petroleum Hydraulic Fluids” for a list of fluids which meet or exceed the

necessary lubrication requirements. Consult factory for use with water base fire

resistant fluids. *Such as Mobil DTE-26, or similar, for pressures over 2000 psi.

Minimum 150 SUS (32 cSt)

Fluid viscosity at Maximum 1000 SUS (216 cSt)

operating temperature Optimum 200-300 SUS (42-65 cSt)

Maximum start-up 4000 SUS (864 cSt)

Fluid temperature Normal inlet fluid temperature should not exceed 140°F (60° C). Always select a fluid

for optimum viscosity at operating temperature. Consult factory for applications assis-

tance when inlet fluid temperatures over 140° F (60° C) are expected.

Seals Fluorocarbon Standard

Filtration Fluid cleanliness per ISO/DIS 4406 should be 18/15 or better for pressures of 2000 psi or

less. For continuous operating pressures of 2000 to 3000 psi, fluid cleanliness should be

17/13 or better.

Response time Full flow to 20-50 ms

(circuit dependent) minimum flow

Recovery time Minimum flow 250-500 ms – two stage compensator

(circuit dependent) to full flow

Weight Single stage 240 lbs. (109 kg)

Two stage 248 lbs. (112.7 kg)

1Flows are actual. Volumetric efficiencies shown in technical data taken into account.

2Metric

4-bolt flange

available

(ISO 3019/2)

available. Please consult factory.

6VPV Vane Pump

Ordering Guide

Code Structure

The alpha-numeric ordering code system enables any particular type of pump to be specified.

Preferred type are also identified by a 10-digit part number for computerized ordering.

Item No Code

1 Code Digit

0513 Vane Pump, stand alone version single pump or combination

2 Direction of Rotation

RClockwise, viewed from shaft end

3 Speed

12 maximum speed; e.g. 1150 rpm = 12

15 1450 rpm = 15

18 1750 rpm = 18

4 Drive Shaft

AKey to DlN 6885

CKey to SAE Standard

DSpline to SAE 744C

5 Bearing Arrangement / Mounting Flange

3Standard bearing arrangement, mounting flange to SAE standards

7Standard bearing arrangement, mounting flange to DIN ISO 3019/2

6 Principle of Operation

VVane Type

7 Mode of Operation

PPump

8 Type of Construction

VVariable displacement pump (open circuit)

KFixed Displacement Pump (available in 1998)

9 Displacement

16 16 cc/rev = .98 cu in/rev

25 25 cc/rev = 1.53 cu in/rev

32 32 cc/rev = 1.95 cu in/rev

45 45 cc/rev = 2.75 cu in/rev

63 63 cc/rev = 3.84 cu in/rev

80 80 cc/rev = 4.88 cu in/rev

100 100 cc/rev = 6.10 cu in/rev

130 130 cc/rev = 7.93 cu in/rev

164 164 cc/rev = 10.00 cu in/rev

Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Pump 1 0513 R 18 C 3 V P V 32 S M 21 F Z B02

Pump 2*** V P V 32 S M 21 F Z B02

Pump 3 (Gear Pump) HY/Z F S11/ 14 R 254

*** When trailing pump is another VPV pump, it can be coded by selecting items 6 through 15 for the

alpha-numeric description. Consult factory for other models and descriptions of trailing pumps.

Price and Part Numbers

See VPV Pump Identification Guide, Publication # 9 535 233 782 for SAE, and 9 535 233 785 for metric

pumps.

Product Literature Disclaimer

Specifications and/or dimensions are subject to change without prior notice. Please consult factory.

VPV Vane Pump 7

Ordering Guide, cont.

Item No Code

10 Housing

S210 bar = 3000 psi.

11 Operating Fluid

CWater glycol

MMineral Oil

DPhosphate ester

12 Operating Pressure

14 Maximum operating pressure; e.g. 14 = 140 bar = 2000 psi

21 21 = 210 bar = 3000 psi

13 Control / Regulator

FPressure regulator - single stage 16/25/32cc only

GPressure regulator - single stage - lockable 16/25/32cc only

HPressure regulator - two stage - with remote option

JCombined pressure/flow compensator (load sense)

STorque limiter (available in 45 to 164cc pumps only)

TProportional P/Q (available 1998)

Solenoid Operated Two Press. Norm. (Normally open)/Normally Low Pressure/Energize to High

XA 115V N.O. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

XB 220V N.O. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

XC 12V N.O. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

XD 24V N.O. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

XE 115V N.O. w/flying leads

XF 220V N.O. w/flying leads

XG 12V N.O. w/flying leads

XH 24V N.O. w/flying leads

XJ 115V N.O. w/DIN 43650 & NG6

XK 220V N.O. w/DIN 43650 & NG6

XL 12V N.O. w/DIN 43650 & NG6

XM 24V N.O. w/DIN 43650 & NG6

XN 115V N.O. w/flying leads & NG6

XO 220V N.O. w/flying leads & NG6

XP 12V N.O. w/flying leads & NG6

XR 24V N.O. w/flying leads & NG6

Solenoid Operated Two Press. Norm. (Normally closed)/Normally High Pressure/Energize to Low

YA 115V N.C. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

YB 220V N.C. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

YC 12V N.C. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

YD 24V N.C. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

YE 115V N.C. w/flying leads

YF 220V N.C. w/flying leads

YG 12V N.C. w/flying leads

YH 24V N.C. w/flying leads

YJ 115V N.C. w/DIN 43650 & NG6

YK 220V N.C. w/DIN 43650 & NG6

YL 12V N.C. w/DIN 43650 & NG6

YM 24V N.C. w/DIN 43650 & NG6

YN 115V N.C. w/flying leads & NG6

YO 220V N.C. w/flying leads & NG6

YP 12V N.C. w/flying leads & NG6

YR 24V N.C. w/flying leads & NG6

8VPV Vane Pump

Ordering Guide, cont.

Item No Code

13 Solenoid Operated Vent Two Press. Norm. (Normally vented)/Energize to Pressure

(cont.) ZA 115V N.V. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

ZB 220V N.V. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

ZC 12V N.V. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

ZD 24V N.V. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

ZE 115V N.V. w/flying leads

ZF 220V N.V. w/flying leads

ZG 12V N.V. w/flying leads

ZH 24V N.V. w/flying leads

Solenoid Operated Vented Norm. High (Normally closed)/Normally at Pressure/Energize to Vent

WA 115V N.C. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

WB 220V N.C. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

WC 12V N.C. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

WD 24V N.C. w/DIN 43650 & quick connect (compression fitting) w/sentinel light

WE 115V N.C. w/flying leads

WF 220V N.C. w/flying leads

WG 12V N.C. w/flying leads

WH 24V N.C. w/flying leads

14 Accessories

SSpecial (Consult Factory)

YMaximum delivery limiter

ZNo other accessories

15 B01 Design Series

P1 Pump 1 of a quick combination unit (adapter kit & coupling required to create a combination-see page 81)

Item No Code

6 Principle of Operation

HY/Z Hydraulic Gear Pump

7 Size Range

F4 cc to 22.5cc

8 Type of Construction

S11 Standard version

S21 Duo (low noise version)

9 Displacement

44 cc/rev = .244 cu in/rev

5.5 5.5 cc/rev = .335 cu in/rev

88 cc/rev = .488 cu in/rev

11 11 cc/rev = .671 cu in/rev

14 14 cc/rev = .854 cu in/rev

16 16 cc/rev = .976 cu in/rev

19 19 cc/rev = 1.159 cu in/rev

22.5 22.5 cc/rev = 1.372 cu in/rev

10 Direction of Rotation

RRight hand (clockwise)

11 Details

254 SAE “A” flange, 2 bolt, SAE keyed shaft

253 SAE “A” flange, 2 bolt, ANSI spline shaft, 9 T, 16/32 pitch

Gear Pump Guide

VPV Vane Pump 9

On the following pages are line graphs of the Performance Characteristics for each of the

pumps in our series. Characteristics are shown at 1200 PSI, 1500 PSI and 3000 PSI. Since

different geographical areas require different data, please refer to the appropriate graph.

Andere Handbücher für VPV 16

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bosch Wasserpumpe Handbücher

Bosch

Bosch REXROTH A4 Series Bedienungsanleitung

Bosch

Bosch UP 15 Bedienungsanleitung

Bosch

Bosch ECP 160 Bedienungsanleitung

Bosch

Bosch rexroth A2FO Series Bedienungsanleitung

Bosch

Bosch VP44 Bedienungsanleitung

Bosch

Bosch Rexroth A10VG Bedienungsanleitung

Bosch

Bosch Rexroth A7VO 63 Series Bedienungsanleitung

Bosch

Bosch Rexroth DBA 2X E Series Bedienungsanleitung

Bosch

Bosch rexroth A4VSO 10 Series Bedienungsanleitung

Bosch

Bosch Rexroth A10VOH145 60 Series Bedienungsanleitung

Bosch

Bosch Rexroth A4VG 40 Series Bedienungsanleitung

Bosch

Bosch Rexroth A10VG Betriebsanleitung

Bosch

Bosch Universal Pump 18V Bedienungsanleitung

Bosch

Bosch rexroth A21VG 10 Series Bedienungsanleitung

Bosch

Bosch Worcester AGS 5 Benutzerhandbuch

Bosch

Bosch rexroth 10 Series Bedienungsanleitung

Bosch

Bosch AGS10-2 Benutzerhandbuch

Bosch

Bosch Rexroth PGH5-MSK133-Air Bedienungsanleitung

Bosch

Bosch Rexroth 63 Series Bedienungsanleitung

Bosch

Bosch Rexroth A10VGT Bedienungsanleitung

Bosch

Bosch GardenPump 18 Bedienungsanleitung

Bosch

Bosch A4VG A4VG 32 Series Bedienungsanleitung

Bosch

Bosch VPV 16 Installations- und Betriebsanleitung

Bosch

Bosch Rexroth A4CSG 30 Series Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung