Bradford White D100T Bedienungsanleitung

238-50845-00B REV 02/16

CONDENSING POWER VENT GAS WATER HEATER

A Spanish language version of these instructions is available by contacting the

company listed on the rating plate.

Hay disponible una versión en español de estas instrucciones al comunicarse con

la compañía que se menciona en la placa de datos de servicio.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electrical switch; do not use any

phone in your building.

Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by a qualified

installer, service agency or the gas supplier.

For your family’s comfort, safety and convenience we

recommend this water heater be installed and serviced by a

plumbing professional.

INSTALLATION AND OPERATION

INSTRUCTION MANUAL

FOR YOUR SAFETY

Do not store or use gasoline or other flammable,

combustible, or corrosive vapors and liquids in the

vicinity of this or any other appliance.

WARNING: If the information in these instructions is not

followed exactly, a fire or explosion may result causing

property damage, personal injury, or death.

CONGRATULATIONS!

You have just purchased one of the finest water

heaters on the market today!

This installation and operation manual will explain in

detail the installation and maintenance of your new

Condensing Power Vent Gas Water Heater. We

strongly recommend that you contact a plumbing

professional for the installation of this water heater.

We require that you carefully read this manual, as well

as the enclosed warranty, and refer to it when

questions arise. If you have any specific questions

concerning your warranty, please consult the

plumbing professional from whom your water heater

was purchased. For your records we recommend that

you write the model, serial number and installation

date of your water heater in the maintenance section in

the back of this manual.

This manual should be kept with the water heater.

TABLE OF CONTENTS

page

GENERAL INFORMATION................................................................. 4

INSTALLATION. ................................................................................. 5

Locating the Water Heater.......................................................... 5

Minimum Clearances .................................................................. 8

Venting ......................................................................................... 8

Vent Pipe Preparation and Joining............................................ 19

Combustion Air Supply .............................................................. 21

Water Connections ..................................................................... 23

Condensate Drain Connection................................................... 26

Gas Connections......................................................................... 27

Electrical Connections................................................................ 28

Wiring Diagram...................................................................... 29

GENERAL OPERATION .................................................................... 30

Lighting and Shutdown Instructions ......................................... 31

Thermostat Adjustment .............................................................. 32

Burner Flame Check ................................................................... 33

MAINTENANCE.................................................................................. 34

TROUBLESHOOTING........................................................................ 37

PARTS LIST AND DRAWING ............................................................ 40

INSTALLATION INSTRUCTIONS FOR POTABLE WATER AND

SPACE HEATING............................................................................... 41

NOTES................................................................................................ 42

GENERAL INFORMATION

This gas-fired water heater is design certified by CSA International under the

American National Standard Z21.10.3 and CAN/CGA 4.3-M most current

editions at the time of manufacture.

This water heater must be installed in accordance with local codes or, in the

absence of local codes, the National Fuel Gas Code, ANSI Z223.1-Latest

Edition) and/or in Canada CAN/CGA B149 Installation Codes (Latest Editions).

The warranty for this water heater is in effect only when the water heater is

installed, adjusted, and operated in accordance with these Installation and

Operation Instructions. The manufacturer will not be held liable for any damage

resulting from alteration and/or failure to comply with these instructions.

This water heater is not design certified for installation in a mobile home. Such

an installation may create a hazardous condition and will nullify the warranty.

Do not use this appliance if any external part to the tank has been submerged

in water. You should contact a qualified service technician to inspect the

appliance and to replace any part of the control system including the gas

control which has been submerged in water. See the Gas Connections section

of this manual before servicing or replacing a water heater that has had any

external part to the tank submerged in water.

Make sure that you check the rating plate and gas control on the water heater

to be certain that the type of gas being supplied corresponds with the marking

on the rating plate and gas control.

CAUTION

Incorrect operation of this appliance may create a hazard to life

and property and will nullify the warranty.

DANGER

Do not store or use gasoline or other flammable, combustible, or

corrosive vapors and liquids in the vicinity of this or any other

appliance.

IMPORTANT

Before proceeding, please inspect the water heater and its components

for possible damage. DO NOT install any water heater with damaged

components. If damage is evident then please contact the supplier where

the water heater was purchased or the manufacturer listed on the rating

plate for replacement parts.

General Information continued-

Sacrificial anodes are used to extend tank life. Anode removal, for any reason

with the exception of anode replacement, except for inspection and/or

replacement, will nullify the warranty. In areas where water is unusually active,

an odor may occur at the hot water faucet due to a reaction between the

sacrificial anodes and the impurities in the water. If this should happen,

alternative anodes may be purchased from the supplier that installed this water

heater. This will minimize the odor while protecting the tank. Additionally, the

water heater should be flushed with appropriate dissolvers to eliminate any

bacteria.

INSTALLATION

Locating the Water Heater

DO NOT install the water heater in any location where gasoline or

flammable vapors are likely to be present.

Water heaters in residential garages must be installed so that all burner(s)

and burner ignition device(s) are located not less than 18 inches (46 cm)

above the floor and must be located or protected to avoid physical

damage. For other installations refer to local codes. In the absence of

local codes, the water heater must be installed in compliance with the

National Fuel Gas Code, ANSI Z223.1 - (Latest Edition) and/or in Canada,

CAN/CGA B149 Installation Codes (Latest Editions).

The location of this water heater is of the utmost importance. Before installing

this water heater, read the installation section of these instructions. After

reading these installation and operation instructions, select a location for the

water heater where the floor is level and is easily accessible to gas and water

supply lines. DO NOT locate the water heater where water lines could be

subjected to freezing temperatures. Make sure the cold water pipes are

not located directly above the gas control so that condensate during

humid weather does not drip on the controls.

WARNING

Water heaters are heat producing appliances. To avoid damage or

injury, do not store materials against the water heater or vent-air intake

system. Use proper care to avoid unnecessary contact (especially by

children) with the water heater and vent-air intake components. UNDER

NO CIRCUMSTANCES MUST FLAMMABLE MATERIALS, SUCH AS

GASOLINE OR PAINT THINNER BE USED OR STORED IN THE

VICINITY OF THIS WATER HEATER, VENT-AIR INTAKE SYSTEM

OR IN ANY LOCATION FROM WHICH FUMES COULD REACH THE

WATER HEATER OR VENT-AIR INTAKE SYSTEM.

Installation (Locating the Water Heater) continued-

Water heater corrosion and component failure can be caused by the heating

and breakdown of airborne chemical vapors. Examples of some typical

compounds that are potentially corrosive are: spray can propellants, cleaning

solvents, refrigerator and air conditioning refrigerants, swimming pool

chemicals, calcium and sodium chloride, waxes and process chemicals. These

materials are corrosive at very low concentration levels with little or no odor to

reveal their presence. NOTE: DAMAGE TO THE WATER HEATER CAUSED

BY EXPOSURE TO CORROSIVE VAPORS IS NOT COVERED BY THE

WARRANTY. DO NOT OPERATE THE WATER HEATER IF EXPOSURE

HAS OR WILL OCCUR. DO NOT STORE ANY POTENTIALLY CORROSIVE

COMPOUNDS IN THE VICINITY OF THE WATER HEATER.

To comply with NSF requirements this water heater is to be:

a) Sealed to the floor with sealant, in a smooth and easily cleanable way,

b) Installed with an optional leg kit that includes legs and/or extensions

that provide a minimum clearance of 6” beneath the water heater.

WARNING

Liquefied petroleum gases/propane gas are heavier than air

and will remain at floor level if there is a leak. Basements,

crawl spaces, closets, and areas below ground level will

serve as pockets for accumulation of leaking gas. Before

lighting, smell all around the appliance area for gas. Be sure

to smell next to the floor.

IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electric switch; do not use any

telephone in your building.

Immediately call your gas supplier from a neighbor’s

telephone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire

department.

DO NOT OPERATE APPLIANCE UNTIL THE LEAKAGE IS

CORRECTED!

Installation (Locating the Water Heater) continued-

The water heater must be located close enough to the outside wall to keep the

venting distance within the maximum distance described in the installation

instructions. Read the venting section in this instruction manual before locating

the water heater.

This water heater must be located in an area where leakage of the tank,

condensate trap or water line connections and the combination temperature

and pressure relief valve will not result in damage to the area adjacent to the

water heater or to lower floors of the structure. Verify all condensate tubing is

properly connected to the blower for proper drainage. When such locations

cannot be avoided, a suitable drain pan adequately piped for proper drainage

must be installed under the water heater. The pan must not restrict combustion

air flow. The drain pan must have a minimum length and width of at least 4 in.

(10.2 cm) greater than the diameter of the water heater and must not restrict

proper combustion air flow to the water heater. The drain pan, as described

above, can be purchased from your plumbing professional. The drain pan must

be piped to an adequate drain. The piping must be at least 3/4 inch (1.9 cm) in

diameter and pitched for proper drainage.

It is recommended that a minimum clearance of 4 inches (10.2 cm) be provided

on the side of the water heater for servicing and maintenance of the

combination temperature and pressure relief valve.

This water heater MUST be installed indoors out of the wind and weather.

Note: For California installation this water heater must be braced,

anchored, or strapped to avoid falling or moving during an earthquake.

See instructions for correct installation procedures. Instructions may be

obtained from DSA Headquarters Office, 1102 Q Street, Sacramento, CA

95811.

WARNING

DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE IF YOU ARE

NOT CERTAIN OF THE FOLLOWING:

Liquefied petroleum gases/propane gas and natural gas have an

odorant added by the gas supplier that aids in the detection of the

gas.

Most people recognize this odor as a “sulfur” or “rotten egg” smell.

Other conditions, such as “odorant fade” can cause the odorant to

diminish in intensity, or “fade”, and not be as readily detectable.

If you have a diminished sense of smell, or are in any way unsure of

the presence of gas, immediately contact your gas supplier from a

neighbor’s telephone.

Gas detectors are available. Contact your gas supplier, or plumbing

professional, for more information.

Minimum Clearances

This installation must allow access to the front of the water heater and

adequate clearance must be provided for servicing and operating this water

heater. The water heater may be installed on either a combustible or non-

combustible floor. If the water heater is to be installed directly on carpeting, it

must be installed on top of a metal or wood panel extending beyond the full

width and depth of the appliance by at least 3 inches (7.6 cm) in any direction

or, if the appliance is to be installed in an alcove or closet, the entire floor must

be covered by the panel. The minimum clearances to combustibles for this

water heater are: 0 inch from the sides and rear, 5 inches (12.7 cm) from the

front of the jacket, 0 inch from the vent connector and 15 inches (38.1 cm) from

the jacket top. Increase distances to provide clearance for servicing.

Venting

Figure 1 - Vent Terminal Clearances

WARNING

Failure to adhere to these installation and operation instructions

may create a hazard to life and property and will nullify the

warranty.

Venting continued-

Canadian

Installations1

US Installations2

A= Clearance above grade, veranda,

porch, deck or balcony

12 inches

(30 cm)

12 inches

(30 cm)

B= Clearance to window or door that may

be opened

36 inches

(91 cm)

4 feet (1.2 m) below or

to the side of opening;

12 inches (30 cm) above

opening

C= Clearance to permanently closed

window

*b *b

D= Vertical clearance to ventilated soffit

located above the terminal within a

horizontal distance of 2 feet (.6 m)

from the center line of the terminal

*b *b

E= Clearance to unventilated soffit *b *b

F= Clearance to outside corner *b *b

G= Clearance to inside corner *b *b

H= Clearance to each side of center line

extended above meter/regulator

assembly

3 feet (.9 m)

within a height

15 feet (4.6 m)

above the

meter/regulator

assembly

I= Clearance to service regulator vent

outlet or oil tank vent

3 feet (.9 m) *b

J= Clearance to non-mechanical air

supply inlet to building or the

combustion air inlet to any other

appliance

12 inches

(30 cm)

4 feet (1.2m) below or to

side of opening;

12 inches (30 cm) above

opening.

K= Clearance to a mechanical air supply

inlet

6 feet

(1.83 m)

3 feet (91 cm) above if

within 10 feet

horizontally

L= Clearance above paved sidewalk or

paved driveway located on public

property

7 feet

(2.13 m)†

7 feet

(2.13 m)†

M= Clearance under a veranda, porch,

deck, or balcony

12 inches

(30 cm) ‡

1 In accordance with the current CAN/CGA-B149 Installation Codes.

2 In accordance with the current ANSI Z223.1-(Latest Edition)/NFPA 54 National Fuel Gas Code.

† A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single-family

dwellings and serves both dwellings.

‡ Permitted only if a veranda, porch, deck or balcony is fully open on a minimum of two sides beneath the floor.

*a) A minimum clearance value determined by testing in accordance with section 2.20.

*b) “Clearance in accordance with local installation codes and the requirements of the gas supplier”.

The vent system must terminate so that proper clearances are maintained as cited

in local codes or the Latest Edition of the National Fuel Gas Code, ANSI

Z223.1.73.4e and 7.8a, b as follows:

1. Do not terminate near soffit vents or crawl space or other area where

condensate or vapor could create a nuisance or hazard or cause property

damage.

2. Do not terminate the exhaust vent terminal where condensate or vapor could

cause damage or could be detrimental to the operation of regulators, relief

valves, or other equipment.

3. Do not terminate the exhaust vent terminal over public area or walkways where

condensate or vapor can cause nuisance or hazard.

4. The vent shall terminate a minimum of 12 inches (25.4 cm) above expected

snowfall level to prevent blockage of vent termination.

Venting continued-

Vent pipes serving power vent appliances are classified by building codes as

“vent connectors”. Required clearances from combustible materials must be

provided in accordance with information in this manual under “Locating the

Water Heater” and “Minimum Clearances”, and with the National Fuel Gas

Code and local codes.

All vent pipes and terminals are to have a 1” minimum clearance to

combustibles. DO NOT use the placement of insulation or other materials in the

required clearance spaces surrounding the venting to combustible material

unless otherwise specified.

WARNING

Risk of carbon monoxide poisoning or fire due to joint separation or

pipe breakage.

This water heater must be properly vented and connected to an approved

vent system in good condition. DO NOT operate the water heater with the

absence of an approved vent system. A clean and unobstructed vent

system is necessary to allow noxious fumes that could cause injury or loss of

life to vent safely and will contribute toward maintaining the water heater’s

efficiency. The acceptance of the venting system is dependent upon full

compliance with these installation instructions.

The venting system must not pass through rated fire separations.

The venting system must be free to expand and contract. This venting

system must be supported in accordance with these instructions.

NOTICE

Single Wall Polypropylene venting systems that are listed on the Bradford

White website are approved for use in the water heaters covered in this

instruction manual. The venting system components are ULC S636

approved and listed by a recognized agency and may be installed in the U.S.

and Canada. Complete instructions for the approved venting systems can be

found on the Bradford White website, www.BradfordWhite.com or by calling

the Technical Service Department at: 800-334-3393.

WARNING

The approved polypropylene venting system Instruction Supplement listed on

the Bradford White website for each manufacturer’s venting system must be

carefully read and followed by a qualified installer. Failure to properly install

the vent system may result in property damage, personal injury, or death.

Inhaltsverzeichnis

Andere Bradford White Boiler Handbücher

Bradford White

Bradford White 40759U Bedienungsanleitung

Bradford White

Bradford White URG1PV40S*N Bedienungsanleitung

Bradford White

Bradford White 500-B Bedienungsanleitung

Bradford White

Bradford White ULG2100H805N Bedienungsanleitung

Bradford White

Bradford White UCG100H199 Bedienungsanleitung

Bradford White

Bradford White LAARS NEOTHERM LC NTH1000 Bedienungsanleitung

Bradford White

Bradford White Magnum D75T125E3N Bedienungsanleitung

Bradford White

Bradford White Ecostor SC Montageanleitung

Bradford White

Bradford White ULG275H763N-475 Bedienungsanleitung

Bradford White

Bradford White M-2-120R6DS-5500W Bedienungsanleitung

Bradford White

Bradford White LD-WH6U3-1 Bedienungsanleitung

Bradford White

Bradford White RG250T6N Bedienungsanleitung

Bradford White

Bradford White UCG100H3993N Bedienungsanleitung

Bradford White

Bradford White EF120T4003NA3 Bedienungsanleitung

Bradford White

Bradford White E32-50S Bedienungsanleitung

Bradford White

Bradford White Defender RG130T N Series Bedienungsanleitung

Bradford White

Bradford White BNTH Bedienungsanleitung

Bradford White

Bradford White Brute BNTH Bedienungsanleitung

Bradford White

Bradford White M-1-20L6DS Bedienungsanleitung

Bradford White

Bradford White RE2H50S 1NCWT Series Bedienungsanleitung

Bradford White

Bradford White Gas Water Heaters Bedienungsanleitung

Bradford White

Bradford White M-4-TW40T6FSX Konfigurationshandbuch

Bradford White

Bradford White Laars MagnaTherm Series Bedienungsanleitung

Bradford White

Bradford White RTG 199 MEN Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung