Bradford White DS140S Beilage

238

41099

00J REV 12/03

DIRECT VENT GAS WATER HEATER

A Spanish language version of these instructions is available by contacting the

company listed on the rating plate.

La version espanola de estas instrucciones se puede obtener al escribirle a la

fabrica cuyo nombre aparece en la placa de especificaciones.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any

phone in your building.

•Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier's instructions.

•If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by a qualified

installer, service agency or the gas supplier.

For your family’s comfort, safety and convenience we

recommend Bradford White water heaters to be installed and

serviced by a plumbing professional.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable,

combustible, or corrosive vapors and liquids in the

vicinity of this or any other appliance.

DS140S & DS150S

INSTALLATION & OPERATING

INSTRUCTION MANUAL

WARNING: If the information in these instructions is not

followed exactly, a fire or explosion may result causing

property damage, personal injury or death.

INTERNET VERSION FOR REFERENCE ONLY

CONGRATULATIONS!

You have just purchased one of the finest water heaters

on the market today!

This installation, operation and instruction manual will

explain in detail the installation and maintenance of your

new Direct Vent Gas Water Heater. We at Bradford White

strongly recommend that you contact a plumbing

professional for the installation of this water heater.

We require that you carefully read this manual, as well as

the enclosed warranty, and refer to it when questions

arise. If you have any specific questions concerning your

warranty, please consult the plumbing professional from

whom your water heater was purchased. For your

records we recommend that you writethe model, serial

number and installation date of your water heater in the

maintenance section in the back of this manual.

This manual should be kept with the water heater.

At Bradford White we’re committed to providing you with

the finest water heater made.

INTERNET VERSION FOR REFERENCE ONLY

TABLE OF CONTENTS page

GENERAL INFORMATION........................................................ 4

INSTALLATION

Locating The Water Heater...................................................... 6

Minimum Clearances................................................................. 9

Optional Direct Vent-Air Intake Terminal Guard.................... 9

Venting........................................................................................ 12

Horizontal and Vertical Vent-Air Intake Lengths ................... 14

Vent-Air Intake System Installation.......................................... 17

Water Connections.................................................................... 25

Gas Connections....................................................................... 29

GENERAL OPERATION............................................................ 30

Lighting and Shutdown Instructions....................................... 31

Thermostat Adjustment............................................................. 32

Burner Flame Checks ............................................................... 33

MAINTENANCE........................................................................... 34

PARTS LIST................................................................................. 37

PARTS LIST DRAWINGS

Direct Vent Water Heater.......................................................... 38

Vent-Air Intake Kits.................................................................... 39

INSTALLATIONS FOR POTABLE WATER AND SPACE

HEATING....................................................................................... 40

INTERNET VERSION FOR REFERENCE ONLY

GENERAL INFORMATION

This gas-fired water heater’s design is certified by CSA International under the

American National Standard Z21.10.1 -(as indicated on the rating plate) and

CSA 4.1-M-(as indicated on the rating plate).

This water heater must be installed in accordance with local codes or, in the

absence of local codes, the National Fuel Gas Code, ANSI Z223.1-Latest

Edition) and/or in Canada CAN/CGA B149 Installation Codes (Latest Editions).

The warranty for this water heater is in effect only when the water heater is

installed, adjusted, and operated in accordance with these Installation and

Operating Instructions. The manufacturer will not be held liable for any damage

resulting from alteration and/or failure to comply with these instructions.

This water heater is not design certified for installation in a mobile home. Such

an installation may create a hazardous condition and will nullify the warranty.

This water heater has been designed and certified for the purpose of heating

potable water. The installation and use of this water heater for any purpose

other than the heating of potable water may cause damage to the water heater

and create a hazardous condition and nullify the warranty.

CAUTION

Incorrect operation of this appliance may create a hazard to life

and property and will nullify the warranty.

Do not use this appliance if any part has been submerged in water. You should

contact a qualified service technician to inspect the appliance and to replace

any part of the control system including the combination gas control which has

been submerged in water.

Do not store or use gasoline or other flammable, combustible, or

corrosive vapors and liquids in the vicinity of this or any other

appliance.

DANGER

INTERNET VERSION FOR REFERENCE ONLY

General Information continued-

IMPORTANT

Before proceeding, please inspect the water heater and its components for

possible damage. DO NOT install any damaged components. If damage is

evident then please contact the supplier where the water heater was

purchased or the manufacturer listed on the rating plate for replacement

parts.

Make sure that you check the rating plate and combination gas control on the

water heater to be certain that the type of gas being supplied corresponds with

the marking on the rating plate and combination gas control.

A sacrificial anode is used to extend tank life. The removal of this anode, for

any reason, will nullify the warranty. In areas where water is unusually active,

an odor may occur at the hot water faucet due to a reaction between the

sacrificial anode and the impurities in the water. If this should happen, an

alternative anode may be purchased from the supplier that installed this water

heater. This will minimize the odor while protecting the tank. Additionally, the

water heater should be flushed with appropriate dissolvers to eliminate any

bacteria.

INTERNET VERSION FOR REFERENCE ONLY

INSTALLATION

LOCATING THE WATER HEATER

WARNING

Water heaters are heat producing appliances. To avoid damage or injury, do

not store materials against the water heater or vent-air intake system. Use

proper care to avoid unnecessary contact (especially by children) with the

water heater and vent-air intake components. UNDER NO CIRCUMSTANCES

MUST FLAMMABLE MATERIALS, SUCH AS GASOLINE OR PAINT

THINNER BE USED OR STORED IN THE VICINITY OF THIS WATER

HEATER, VENT-AIR INTAKE SYSTEM OR IN ANY LOCATION FROM

WHICH FUMES COULD REACH THE WATER HEATER OR VENT-AIR

INTAKE SYSTEM.

DO NOT install the water heater in any location where gasoline or

flammable vapors are likely to be present.

Water Heaters in residential garages shall be installed so that all

burner(s) and burner ignition device(s) are located not less than 18

inches (46 cm) above the floor and shall be located, or protected, to

avoid physical damage. For other installations refer to local codes. In

the absence of local codes, the water heater shall be installed in

compliance with the National Fuel Gas Code, ANSI Z223.1 -(Latest

Edition) and/or in Canada, CAN/CGA B149 Installation Codes(Latest

Editions).

The location of this water heater is of the utmost importance. Before installing

this water heater, read the installation section of these instructions. After

reading these installation and operating instructions, select a location for the

water heater where the floor is level and is easily accessible to gas and water

supply lines. DO NOT locate the water heater where water lines could

be subjected to freezing temperatures. Make sure the cold water pipes

are not located directly above the gas control so that condensate

during humid weather does not drip on the controls.

INTERNET VERSION FOR REFERENCE ONLY

Installation (Locating The Water Heater) continued-

Water heater corrosion and component failure can be caused by the heating

and breakdown of airborne chemical vapors. Examples of some typical

compounds that are potentially corrosive are: spray can propellants, cleaning

solvents, refrigerator and air conditioning refrigerants, swimming pool

chemicals, calcium and sodium chloride, waxes and process chemicals.

These materials are corrosive at very low concentration levels with little or no

odor to reveal their presence. NOTE: DAMAGE TO THE WATER HEATER

CAUSED BY EXPOSURE TO CORROSIVE VAPORS IS NOT COVERED BY

THE WARRANTY. DO NOT OPERATE THE WATER HEATER IF

EXPOSURE HAS OR WILL OCCUR. DO NOT STORE ANY POTENTIALLY

CORROSIVE COMPOUNDS IN THE VICINITY OF THE WATER HEATER.

WARNING

Liquefied petroleum gases/propane gas are heavier than air

and will remain at floor level if there is a leak. Basements,

crawl spaces, closets and areas below ground level will

serve as pockets for accumulation of leaking gas. Before

lighting, smell all around the appliance area for gas. Be sure

to smell next to the floor.

IF YOU SMELL GAS:

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any

telephone in your building.

•Immediately call your gas supplier from a neighbor’s

telephone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire

department.

DO NOT OPERATE APPLIANCE UNTIL THE LEAKAGE IS

CORRECTED!

INTERNET VERSION FOR REFERENCE ONLY

Installation (Locating The Water Heater) continued-

WARNING

DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE IF YOU ARE

NOT CERTAIN OF THE FOLLOWING:

•Liquefied petroleum gases/propane gas and natural gas have

an odorant added by the gas supplier that aids in the detection

of the gas.

•Most people recognize this odor as a “sulfur” or “rotten egg”

smell.

•Other conditions, such as “odorant fade” can cause the odorant

to diminish in intensity, or ”fade”, and not be as readily

detectable.

•If you have a diminished sense of smell, or are in any way unsure

of the presence of gas, immediately contact your gas supplier

from a neighbor’s telephone.

•Gas detectors are available. Contact your gas supplier, or

plumbing professional, for more information.

The water heater must be located close enough to the outside wall to keep the

venting distance within the maximum distance described in the installation

instructions. Note: The direct vent-air intake terminal must be installed on a

vertical wall. Read the venting section in this installation instruction manual

before locating the water heater.

This water heater must be located in an area where leakage of the tank or

water line connections and the combination temperature and pressure relief

valve will not result in damage to the area adjacent to the water heater or to

lower floors of the structure. When such locations cannot be avoided, a

suitable drain pan, adequately drained, be installed under the water heater.

The pan must not restrict combustion airflow. The drain pan must be no

greater than 1-½ inches (3.8 cm) deep and have a minimum length and width

of at least four (4) inches (10.2 cm) measured from the jacket of the water

heater. The drain pan, as described above, can be purchased from your

plumbing professional. The drain pan must be piped to an adequate drain.

The piping must be at least 3/4 inch (1.9 cm) in diameter and pitched for

proper drainage.

It is recommended that a minimum clearance of four (4) inches (10.2 cm) be

provided on the side of the water heater for servicing and maintenance of the

combination temperature and pressure relief valve.

INTERNET VERSION FOR REFERENCE ONLY

Installation continued-

MINIMUM CLEARANCES

WARNING

Failure to adhere to these installation and operating instructions

may create a hazard to life and property and will nullify the

warranty.

This installation shall allow access to the front of the water heater and

adequate clearance shall be provided for servicing and operating this

water heater. The water heater may be installed on either a combustible or

non-combustible floor. If the water heater is to be installed directly on

carpeting, it shall be installed on top of a metal or wood panel extending

beyond the full width and depth of the appliance by at least three (3) inches

(7.6 cm) in any direction or, if the appliance is to be installed in an alcove or

closet, the entire floor shall be covered by the panel. The minimum clearances

to combustibles for this water heater is: zero (0) inch (0 cm) from the sides

and rear, four (4) inches (10.2 cm) from the front of the jacket, zero (0) inch (0

cm) from the plenum, zero (0) inch (0 cm) from the air intake elbow and

telescopic tubes and twelve (12) inches (30.5 cm) from the direct vent-air

intake terminal. (See Figure 1).

OPTIONAL DIRECT VENT-AIR INTAKE TERMINAL GUARD

WARNING

The direct vent-air intake terminal is HOT while the water heater is

in operation. Do not touch. Keep children, combustibles, gasoline

and other liquids having flammable vapors away.

It is recommended that a vent-air intake terminal guard be installed when the

vent-air intake terminal is located where it can be touched accidentally, or

accessed by children. (See Figure 2).

A chain link or louvered fence may be used instead of the vent-air intake

terminal guard. Maintain proper clearances as specified in this instruction

manual to the vent-air intake terminal. (See Figure 3).

INTERNET VERSION FOR REFERENCE ONLY

Installation (Minimum Clearances) continued-

Figure 1

INTERNET VERSION FOR REFERENCE ONLY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradford White Boiler Handbücher

Bradford White

Bradford White RE2H50R10-1NCWW Originalbetriebsanleitung

Bradford White

Bradford White UCG100H199 Bedienungsanleitung

Bradford White

Bradford White UPDX series Bedienungsanleitung

Bradford White

Bradford White RTG 199 HEN Bedienungsanleitung

Bradford White

Bradford White Defender RG140T Series Bedienungsanleitung

Bradford White

Bradford White M1TW40S Series Bedienungsanleitung

Bradford White

Bradford White 238-37281-00R Beilage

Bradford White

Bradford White Defender RG130T N Series Bedienungsanleitung

Bradford White

Bradford White D65T625 Bedienungsanleitung

Bradford White

Bradford White S-SW2-60R6DS Bedienungsanleitung

Bradford White

Bradford White DV Series Bedienungsanleitung

Bradford White

Bradford White Everhot IGE-199R Series Beilage

Bradford White

Bradford White EFT-5500-4-S-10 Bedienungsanleitung

Bradford White

Bradford White Laars MagnaTherm Series Bedienungsanleitung

Bradford White

Bradford White MI30T*F(BN Bedienungsanleitung

Bradford White

Bradford White RG250T6X-506 Bedienungsanleitung

Bradford White

Bradford White 65T-65FB-3N Bedienungsanleitung

Bradford White

Bradford White ERE240 Bedienungsanleitung

Bradford White

Bradford White PDX Series Bedienungsanleitung

Bradford White

Bradford White mi5036en10 Bedienungsanleitung

Bradford White

Bradford White 50T65F Bedienungsanleitung

Bradford White

Bradford White Eco-Magnum Series Bedienungsanleitung

Bradford White

Bradford White Copper Brute II Bedienungsanleitung

Bradford White

Bradford White EF100T150(E)*(N Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung