Bradford White ES-2400-1-S-10 Bedienungsanleitung

ELECTRIC INSTANTANEOUS TANKLESS WATER HEATER

INSTALLATION GUIDE AND OWNERS MANUAL

ELEMENT CARTRIDGE

HEATER MODEL/ORDER REF. CARTRIDGE REF #

RELAY

PART#EX250B-

EX254B

FLOW RESTRICTOR

AERATOR

PART # EX0061-0.5-AER

CONTROL BOARD

EX0183DL-30A for

120V, 277V,

240V, 208V

REPLACEMENT PARTS FOR “Single Point”MODELS

CALL TECHNICAL SERVICE

@ 1-800-334-3393

COMPRESSION

SLEEVE 3/8”

PART # EX68C

COMPRESSION

NUT 3/8”

PART #EX68B

WARNING

BEFORE ATTEMPTING INSTALLATION OF THIS UNIT OR MAKING ANY

ADJUSTMENTS TO THE UNIT, BE SURE CIRCUIT BREAKER IS OFF

TO PREVENT DANGER OF SERIOUS ELECTRIC SHOCK.

FAILURE TO GROUND THE SYSTEM MAY RESULT IN SERIOUS INJURY OR DEATH

INSTALLER/ CONSUMER RESPONSIBILITIES

READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING TO INSTALL OR

OPERATE THIS WATERHEATING UNIT. IF THE SAFETY RULES ARE NOT

FOLLOWED, THE UNIT WILL NOT OPERATE PROPERLY AND COULD CAUSE

DEATH, SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARRANTY

OF THIS UNIT WILL DEPEND ON PROPER INSTALLATION AND OPERATION.

THE WARRANTY WILL BE VOID IF THE DESIGN HAS BEEN ALTERED IN ANY WAY

WHATSOEVER. THE MANUFACTURER OF THIS UNIT WILL NOT BE LIABLE

FOR ANY DAMAGES BECAUSE OF FAILURE TO COMPLY WITHTHE INSTALLATION

AND OPERATING INSTRUCTIONS OUTLINED ON THE FOLLOWING PAGES.

THE INSTALLATION MUST CONFORM WITHTHE INSTRUCTIONS IN THIS

MANUAL AND THE LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES,

WITH THE LATEST EDITION OF THE NATIONAL ELECTRICAL CODE. THE

NATINOAL ELECTRICAL CODE IS AVAILABLE FROM WRITING

UNDERWRITERS LABORATORIES, 333 PFINGSTEN RD.,

NORTHBROOK, IL. 60062

IF ASSTANCE IS REQUIRED OR ANY QUESTIONS RELATING

TO THE INSTALLATION OR PERFORMANCE OF THIS UNIT ARISE,

PLEASE CONTACT

TECHNICAL SERVICE TOLL FREE:1-800-334-3393.

HAVE THE INFORMATION LISTED BELOW BEFORE CALLING:

MODEL NO.___________SERIAL NO.___________INSTALLATION DATE_____

“SINGLE POINT”

MODELS COVERED:

ES-2400-1-S-10 ES-3000-1-S-10

ES-3000-2-S-10 ES-3000-5-S-10

ES-3500-1-S-10 ES-3500-4-S-10

ES-4100-2-S-10 ES-4100-5-S-10

ES-5500-4-S-10

ES-2400-1-S-10 120V EX610SP

ES-3000-1--S-10 120V EX480SP

ES-3500-1-S-10 120V EX410SP

ES-3000-2-S-10 120V EX1440SP

ES-4100-2-S-10 208V EX1050SP

ES-3500-5-S-10 240V EX1650SP

ES-4100-5-S-10 277V EX1870SP

ES-3000-5-S-10 277V EX2500SP

ES-5500-4-S-10 240V EX1050SP

INSTALL

THIS WAY UP

ONLY !

relay

PLUMBING CONNECTIONS

1) The unit is supplied with 3/8’’ compressionfittings.USE THESE: DO NOT

USE THREADED PIPE FITTINGS. DO NOT USE PIPE DOPE OR TEFLON

TAPE ON THIS INSTALLATION.Ensure the inlet filter supplied with thisunit

is in place.

2) Ensure that the pipes are correctly aligned with the inlet and

outlet bosses to avoid excessive stress on the heater body molding of the

unit.

NOTE: Run water through the supply pipe to remove all debris from the

pipe before connecting to the unit. Failure to do so could damage the flow

switch.

3) Install isolating valves (shut-off type),or equivalent on both inlet and outlet

pipes. This allows the unit to be isolatedfor maintenancepurposes. (Fig. 2)

4) Whenall plumbing is complete, inspect the system for water leaks

at all plumbingconnections. If a water leak is present take corrective action.

If a water leak is at the compressionfitting, slowly tighten compressionnut

until the water leaks ceases.

Fully open both inlet and outlet shut-off valves.

Run all hot water outlets fed by this heater one at a timeuntil thewater flow

is continuous and free from “gulping”and all visible air pockets.

NOTE:

ALL PLUMBING AND MOUNTING MUST BE COMPLETED

BEFORE PROCEEDING WITHTHE

ELECTRICAL HOOK-UP.

TEST THE INSTALLATION FOR LEAKS BEFORE

CONNECTING THE ELECTRICAL SUPPLY.

Inlet

filter

GENERAL

This “Single Point”water heating unit is specificallydesigned to be installed

“under sink”feeding a SINGLE faucet. This unit is designed to take in cold water

ONLY and heat it to temperaturessuitable for hand washing. To obtain optimum

performance and energy savings, the unit should be located as near as possible

to the point of use. This unit incorporatesa constant flow device and shouldonly

be used with the faucet aerator supplied.The unit is supplied with compression

rings and nuts suitablefor direct coupling to 3/8”copper or plastic piping. Do not

use additional screwed fittingsor pipe dope. The use of such materials will void

the warranty. DO NOT SOLDER PIPES WHILE THE UNIT IS INSTALLED

(serious damage to the electronic flow switch will result).

INSTALLING THE UNIT

1) The unit must be mounted underneath a sink in a VERTICAL position with

the inlet and the outlet at the TOP. Mounting in any way other than this

WILL cause element burn out and possibly damage the unit further.

Do not install this unit above the faucet as the siphoning effect will drain

the heater which can cause element burn out and damage the unit.

2) The cold water inlet is on the right hand side and the hot water outlet is

on the left hand side. Under NO circumstances can these be reversed.

3) Leave a minimum of 8”below the unit for easy replacement of the

element.

4) This unit should be fixed to the wall using the four mounting holes at

each corner of the backplate.

THIS HEATER MUST HAVE ITS OWN INDEPENDENT CIRCUIT, USING A

CORRECTLY RATED CIRCUIT BREAKER AND WIRES SUITABLE FOR AT

LEAST 75 OC OPERATION.

WARNING

UNIT MUST BE PROPERLY GROUNDED TO THE “GND”LOCATION

ON THE TERMINAL BLOCK. FAILURE TOGROUNDTHE SYSTEM MAY

RESULT IN SERIOUS INJURY OR DEATH.

WARNING

BEFORE BEGINNING ANY WORK ON THE ELECTRICAL INSTALLATION BE SURE

THAT THE CIRCUIT BREAKER IS IN THE “OFF”POSITION TO AVOID ANY

DANGER OF ELECTRICAL SHOCK.

MODEL

VOLTS*

OUTPUT

CURRENT

TEMPERATURE RISE

AMPS

0.5 gpm

0.6 gpm

0.7 gpm

ES-2400-1-S-10

120

2.4

ES-3000-1-S-10

120

3.0

ES-3500-1-S-10

120

3.5

29.2

ES-3000-2-S-10

208

3.0

14.4

ES-4100-2-S-10

208

4.1

19.7

ES-3000-5-S-10

277

3.0

10.8

ES-4100-5-S-10

277

4.1

14.8

ES-3500-4-S-10

240

3.5

14.6

ES-5500-4-S-10

240

5.5

RATINGS OF ‘’SINGLE POINT ”MODELS

* Units must be installed at rated voltage ONLY

THIS HEATER MUST BE INSTALLED ONLY IN A VERTICAL POSITION

WITH THE INLET AND OUTLET AT THE TOP

ELECTRICAL CONNECTIONS

This water heating must have its own independent circuit using

insulated, UL listed, 3 wire cable of the appropriatesize suitable

for use up to 75°C protected by the correctly rated circuit breaker.

WARNING

Unit must be properly grounded to the “GND”locationon the terminalblock.

Failure to ground the system may result in serious injury or loss of life

Wire entry into the unit should be made throughthe lower right hand corner of the

backplate via one of the two “knockout”holes provided.

The “mains”wires should be connected to the slots in the terminalblock marked

L1 and L2 (N). The ground lead must be connected to the slot marked

Failure to ground the system may result in death or serious injury.

WARNING

This water heater must not be switched “on”if there is a possibilitythat

the water in the heater is frozen

TO APPROPRIATE

SIZE BREAKER

WIRE ENTRY

EITHER THROUGH

REAR OR

BOTTOM

KNOCK-OUTS

MOUNTING HOLES

4 1/4 inches

8 inches

APPROPRIATE

GAUGE COPPER

WIRE (2 conductors

1 ground)

INSTALL

THIS WAY UP

ONLY !

relay

ECO –AUTO

RESETTING HIGH

TEMPERATURE CUT-

OUT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradford White Boiler Handbücher

Bradford White

Bradford White PV Series Bedienungsanleitung

Bradford White

Bradford White ECOSTOR2 SDW2504T Betriebsanleitung

Bradford White

Bradford White MI30T*F(BN Bedienungsanleitung

Bradford White

Bradford White ElectriFLEX LD LE Series Bedienungsanleitung

Bradford White

Bradford White UCG100H399 Bedienungsanleitung

Bradford White

Bradford White EVERHOT IGI-180C Series Beilage

Bradford White

Bradford White URG250H6N-475-264 Bedienungsanleitung

Bradford White

Bradford White TTW URG2PV50H6N Bedienungsanleitung

Bradford White

Bradford White Eco-Magnum Series Bedienungsanleitung

Bradford White

Bradford White PDX1-40S6FBN Beilage

Bradford White

Bradford White ECO-DEFENDER EURG2DV40S N Series Bedienungsanleitung

Bradford White

Bradford White EFC-5500-4-S-10 Bedienungsanleitung

Bradford White

Bradford White UPV Series Bedienungsanleitung

Bradford White

Bradford White Brute MagnaTech BCFH1000 Bedienungsanleitung

Bradford White

Bradford White Combi2 TTW C-DW2-TW50T10FBN Bedienungsanleitung

Bradford White

Bradford White M-4-TW40T6FSX Konfigurationshandbuch

Bradford White

Bradford White TTW URG2PV75H6N Bedienungsanleitung

Bradford White

Bradford White BW200-R Bedienungsanleitung

Bradford White

Bradford White CDW2TW Anwendungshandbuch

Bradford White

Bradford White DW280L Montageanleitung

Bradford White

Bradford White M-2-120R6DS-5500W Bedienungsanleitung

Bradford White

Bradford White Condensing PV Series Bedienungsanleitung

Bradford White

Bradford White SW-2-40R-L Bedienungsanleitung

Bradford White

Bradford White PDX250T Series Anwendungshandbuch

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung