Bradford White RG1D Montageanleitung

238-51004-00A REV 11/14

DAMPER EQUIPPED

GAS WATER HEATER

A Spanish language version of these instructions is available by contacting

the company listed on the rating plate.

La version espanola de estas instrucciones se puede obtener al escribirle

a la fabrica cuyo nombre aparece en la placa de especificaciones.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electrical switch; do not use any

phone in your building.

Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier's

instructions.

If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by a qualified

installer, service agency or the gas supplier.

For your family’s comfort, safety and convenience, we recommend this

water heater to be installed and serviced by a plumbing professional.

INSTALLATION & OPERATION INSTRUCTION

MANUAL For Flammable Vapor Ignition Resistant

System Equipped Water Heater

For Your Safety

Do not store or use gasoline or other flammable, combustible,

or corrosive vapors and liquids in the vicinity of this or any

other appliance.

WARNING: If the information in these instructions is not followed

exactly, a fire or explosion may result causing property damage,

personal injury or death.

CONGRATULATIONS!

You have just purchased one of the finest water heaters on the market

today!

This installation, operation and instruction manual will explain in detail

the installation and maintenance of your new Damper Equipped

Flammable Vapor Ignition Resistant Gas Water Heater. We strongly

recommend that you contact a plumbing professional for the installation

of this water heater.

We require that you carefully read this manual, as well as the enclosed

warranty, and refer to it when questions arise. If you have any specific

questions concerning your warranty, please consult the plumbing

professional from whom your water heater was purchased. For your

records we recommend that you write the model, serial number and

installation date of your water heater in the maintenance section in the

back of this manual.

Special Flammable Vapor Ignition Resistant System:

This water heater is equipped with a Flammable Vapor Ignition Resistant

System. In the event of improper usage or storage of gasoline or other

flammable materials in the location where the water heater is installed, the

technology will resist ignition of the flammable vapors outside the confines of

the water heater.

The Flammable Vapor Ignition Resistant System features:

Advanced Flame Arrestor Design

Re-settable Thermal Switch/Intelligent Diagnostic Control to prevent

burner/pilot operation with restricted airflow

Flammable Vapor Sensor

Automatic Ignition Device

Sight Window to observe operation of pilot and burner

FOR YOUR SAFETY: Activation of the Flammable Vapor Ignition Resistant

System occurs when flammable vapors are drawn into the water heater and

are combusted. If flammable vapors are detected:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your

building.

Leave the premises and immediately call the fire department from a

neighbor’s phone. Follow the fire department’s instructions.

Once the flammable vapor has been evacuated, contact your plumbing

professional or the manufacturer for further instructions. Replacement of a

Flammable Vapor Ignition Resistant System equipped water heater due to a

flammable vapor shutdown is not covered under the terms of the limited

warranty.

TABLE OF CONTENTS

Page

GENERAL INFORMATION...................................................................4

INSTALLATION ....................................................................................6

Locating the Water Heater...............................................................6

Minimum Clearances .......................................................................9

Venting ............................................................................................10

Combustion Air Supply .................................................................11

Water Connections.........................................................................13

Gas Connections............................................................................16

Electrical Connections...................................................................17

Wiring Diagram...............................................................................18

GENERAL OPERATION.....................................................................20

Lighting and Shutdown Instructions............................................21

Thermostat Adjustments ...............................................................21

Burner Flame Check ......................................................................23

MAINTENANCE ..................................................................................25

TROUBLESHOOTING ........................................................................29

INSTALLATION INSTRUCTIONS FOR POTABLE WATER .............34

PARTS LIST........................................................................................35

INSTALLATION INSTRUCTIONS FOR POTABLE WATER AND

SPACE HEATING ...............................................................................39

NOTES ................................................................................................40

GENERAL INFORMATION

This gas-fired water heater is design certified by CSA International under the

applicable American National Standard, Z21.10.1-Latest Edition or CSA 4.1-

Latest Edition, available from CSA International, 8501 East Pleasant Valley

Road, Cleveland, OH 44131-5575, USA.

This water heater must be installed in accordance with local codes. In the

absence of local codes, it must be installed in compliance with the National

Fuel Gas Code, ANSI Z223.1-Latest Edition, or in Canada, Natural Gas

Installation Code, CAN/CGA B149.1-Latest Edition, or Propane Installation

Code, CAN/CGA B149.2-Latest Edition. The warranty for this water heater is

in effect only when the water heater is installed, adjusted, and operated in

accordance with these Installation and Operating Instructions. The

manufacturer will not be liable for any damage resulting from alteration and/or

failure to comply with these instructions.

This water heater is not design certified for installation in a mobile home.

Such an installation may create a hazardous condition and will void the

warranty.

This water heater has been designed and certified for the purpose of heating

potable water. The installation and use of this water heater for any purpose

other than the heating of potable water may cause damage to the water

heater, create a hazardous condition, and void the warranty.

CAUTION

Incorrect operation of this water heater may create a hazard to life and

property and will void the warranty.

WARNING

Prior to connecting the gas supply line to a gas fired water heater, ensure

that the gas supply line does not have moisture/water or dirt/scale inside

the gas line. Commonly this check is done at the lowest point in the gas

distribution system prior to gas burning appliances.

Do not use this appliance if any external part to the tank has been submerged

in water. You should contact a qualified service technician to inspect the

appliance and to replace any part of the control system including the

combination gas control which has been submerged in water. See the Gas

Connections section of this manual before servicing or replacing a water

heater that has had any external part to the tank submerged in water.

DANGER

Do not store or use gasoline or other flammable, combustible, or corrosive

vapors and liquids in the vicinity of this or any other appliance.

General Information continued-

IMPORTANT

Before proceeding, please inspect the water heater and components for

possible damage. DO NOT install any damaged components. If damage

is evident, please contact the supplier where the water heater was

purchased or the manufacturer listed on the rating plate for replacement

parts.

This water heater has been manufactured for operation at altitudes from sea

level to 2000 feet (610 m) (unless otherwise specified on the water heater

rating plate). For use of this water heater at an elevation greater than 2000

feet (610 m), contact the dealer or manufacturer listed on the rating plate for

information on any necessary modifications. Uncorrected operation of this

water heater may create a hazard to life and property.

Make sure that you check the rating plate and combination gas control on the

water heater to be certain that the type of gas being supplied corresponds with

the marking on the rating plate and combination gas control.

A sacrificial anode is used to extend tank life. The removal of this anode, for

any reason, will void the warranty. In areas where water is unusually active,

an odor may occur at the hot water faucet due to a reaction between the

sacrificial anode and the impurities in the water. If this should happen, an

alternative anode may be purchased from the supplier that installed this water

heater. This will minimize the odor while protecting the tank. Additionally, the

water heater should be flushed with appropriate dissolvers to eliminate any

bacteria.

INSTALLATION

Locating the Water Heater

WARNING

Water heaters are heat producing appliances. To avoid damage or injury,

there must be no materials stored against the water heater or vent-air intake

system, and proper care must be taken to avoid unnecessary contact,

especially by children, with the water heater and vent-air intake components.

UNDER NO CIRCUMSTANCES SHALL FLAMMABLE MATERIALS SUCH

AS GASOLINE OR PAINT THINNER BE USED OR STORED IN THE

VICINITY OF THIS WATER HEATER, VENT-AIR INTAKE SYSTEM OR IN

ANY LOCATION FROM WHICH FUMES COULD REACH THE WATER

HEATER OR VENT-AIR INTAKE SYSTEM.

This water heater must NOT be installed in any location where gasoline or

flammable vapors are likely to be present, unless the installation is such to

eliminate the probable ignition of gasoline or flammable vapors.

Water heaters in residential garages must be installed and located, or

protected, to avoid physical damage. For other installations refer to local

codes. In the absence of local codes, the water heater must be installed in

compliance with the National Fuel Gas Code, ANSI Z223.1- Latest Edition, or

in Canada, Natural Gas Installation Code, CAN/CGA B149.1-Latest Edition, or

Propane Installation Code, CAN/CGA B149.2-Latest Edition.

The location of this water heater is of the utmost importance. Before installing

this water heater, read the Installation section of these instructions. After

reading these Installation and Operation Instructions, select a location for the

water heater where the floor is level and is easily accessible to gas and water

supply lines. DO NOT locate the water heater where water lines could be

subjected to freezing temperatures. Make sure the cold water pipes are not

located directly above the gas control, so that condensate during humid

weather does not drip on the controls.

This water heater MUST be installed indoors out of the wind and weather.

To comply with NSF requirements, this water heater is to be:

a) Sealed to the floor with sealant, in a smooth and easily cleanable way,

or;

b) Installed with an optional leg kit that includes legs and/or extensions

that provide a minimum clearance of 6” beneath the water heater.

Installation (Locating the Water Heater) continued-

Note: For California installations, this water heater must be braced, anchored,

or strapped to avoid falling or moving during an earthquake. See instructions

for correct installation procedures. Instructions may be obtained from DSA

Headquarters Office, 1102 Q Street, Suite 5100, Sacramento, California

95811.

Water heater corrosion and component failure can be caused by the heating

and breakdown of airborne chemical vapors. Examples of some typical

compounds that are potentially corrosive are: spray can propellants, cleaning

solvents, refrigerator and air conditioning refrigerants, swimming pool

chemicals, calcium and sodium chloride, waxes and process chemicals.

These materials are corrosive at very low concentration levels with little or no

odor to reveal their presence. NOTE: DAMAGE TO THE WATER HEATER

CAUSED BY EXPOSURE TO CORROSIVE VAPORS IS NOT COVERED BY

THE WARRANTY. DO NOT OPERATE THE WATER HEATER IF

EXPOSURE HAS OR WILL OCCUR. DO NOT STORE ANY POTENTIALLY

CORROSIVE COMPOUNDS IN THE VICINITY OF THE WATER HEATER.

WARNING

Liquefied petroleum gases/propane gas are heavier than air and will

remain at floor level if there is a leak. Basements, crawl spaces, closets

and areas below ground level will serve as pockets for accumulation of

leaking gas. Before lighting, smell all around the appliance area for gas.

Be sure to smell next to the floor.

If You Smell Gas:

Do not try to light any appliance.

Do touch any electrical switch; do not use any telephone in your

building.

Immediately call your gas supplier from a neighbor’s telephone.

Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

Do not operate appliance until leakage is corrected!

Installation (Locating the Water Heater) continued-

WARNING

DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE IF YOU ARE NOT

CERTAIN OF THE FOLLOWING:

Liquefied petroleum gases/propane gas and natural gas have an

odorant added by the gas supplier that aids in detection of the gas.

Most people recognize this odor as a “sulfur” or “rotten egg” smell.

Other conditions, such as “odorant fade” can cause the odorant to

diminish in intensity, or “fade,” and not be as readily detectable.

If you have a diminished sense of smell, or are in any way unsure of the

presence of gas, immediately contact your gas supplier from a

neighbor’s telephone.

Gas detectors are available. Contact your gas supplier or plumbing

professional for more information.

Proper venting practices must be considered when selecting a location for this

water heater. For exact venting specifications, please consult the Venting

section of these Installation and Operating Instructions.

This water heater must be located in an area where leakage of the tank, water

line connections, or the combination temperature and pressure relief valve will

not result in damage to the area adjacent to the water heater or to lower floors

of the structure. When such locations cannot be avoided, a suitable drain pan

must be installed under the water heater. The drain pan must have a minimum

length and width of at least 4 in. (10.2 cm) greater than the diameter of the

water heater and must not restrict proper combustion air flow to the water

heater. The drain pan, as described above, can be purchased from your

plumbing professional. The drain pan must be piped to an adequate drain.

The piping must be at least 3/4 in. (1.9 cm) in diameter and pitched for proper

drainage.

It is recommended that a minimum clearance of 4 in. (10.2 cm) be provided on

the side of the water heater for servicing and maintenance of the combination

temperature and pressure relief valve.

Minimum Clearances

WARNING

Failure to adhere to these installation and operating instructions may

create a hazard to life and property and will nullify the warranty.

This installation MUST allow access to the front of the water heater and

adequate clearance must be provided for servicing and operating this water

heater. The water heater may be installed on either a combustible or non-

combustible floor. If the water heater is to be installed directly on carpeting, it

must be installed on top of a metal or wood panel (or equivalent) extending

beyond the full width and depth of the water heater by at least 3 in. (7.6 cm) in

any direction or, if the appliance is to be installed in an alcove or closet, the

entire floor must be covered by the panel. If the rating plate or the label on the

front of the heater specifies minimum clearances less than those listed in the

below table, the water heater must be installed in accordance with the

minimum clearances listed on the rating plate or the label on the front of the

heater. Increase distances to provide clearance for servicing.

If it is necessary to install this water heater in an alcove, use the clearances

listed in Figure 1.

Figure 1. Minimum Clearances for an Alcove Installation.

Venting

WARNING

The venting system must be installed properly following all local codes or

in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1-

Latest Edition, or in Canada, The Natural Gas and Propane Installation

Code, B149-Latest Edition. Failure to properly install the venting system

could result in property damage, personal injury, or death.

This water heater has been shipped with a draft hood, also called a draft

diverter, for which it was designed. The water heater must be operated with

this draft hood properly installed on the damper bracket. If ever removed, the

draft hood must be replaced in the same position and properly secured.

WARNING

Carefully inspect the venting system of a replacement water heater

installation before connecting to the venting system. All joints in the vent

connector must be securely fastened with screws and fit tightly together.

Inspect the venting system for signs of deterioration (rust and perforation)

and replace any sections that are not in good condition.

The chimney must be lined and in good condition. Check to make sure the

venting system is properly sized for the water heater. If the venting system

was previously sized for another gas appliance that has been removed, the

venting system may now be too large. Refer to the National Fuel Gas Code

ANSI Z223.1-Latest Edition, or in Canada, the Natural Gas and Propane

Installation Code, B149-Latest Edition, for the correct sizing of venting

systems and common venting with another gas appliance.

Do not vent this water heater into the venting system of another gas

appliance designed to vent under positive pressure.

The water heater should be installed as close as practical to the venting

system to minimize the vent connector length required. Refer to local codes

for the distance limitations on vent connector lengths.

At the completion of the water heater installation, the burner and venting

system must be checked for proper operation with all other commonly

vented appliances in operation. Check for spillage of flue products around

the outside relief opening of the draft hood after several minutes of

operation. The flame from a match should be drawn into the draft hood. Do

not use the water heater or connected equipment if spillage is detected until

the problem is corrected. Refer to the latest edition of the National Fuel

Gas Code, or in Canada, the Natural Gas and Propane Installation Code for

complete details on the “Procedure to Be Followed to Place Equipment in

Operation.”

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradford White Boiler Handbücher

Bradford White

Bradford White S-SW2-60R6DS Bedienungsanleitung

Bradford White

Bradford White Everhot IGE-199R Series Beilage

Bradford White

Bradford White eF Series Bedienungsanleitung

Bradford White

Bradford White ElectriFLEX HD CEHD50 Bedienungsanleitung

Bradford White

Bradford White URG1D30T*N Bedienungsanleitung

Bradford White

Bradford White KwickShot Bedienungsanleitung

Bradford White

Bradford White MAGNUM Series Bedienungsanleitung

Bradford White

Bradford White ES-2400-1-S-10 Bedienungsanleitung

Bradford White

Bradford White RE1 Bedienungsanleitung

Bradford White

Bradford White EF-60T-125 Bedienungsanleitung

Bradford White

Bradford White LD-12UT3-1 Bedienungsanleitung

Bradford White

Bradford White GX225S BN Series Bedienungsanleitung

Bradford White

Bradford White DS1-40S6FBN Handbuch

Bradford White

Bradford White MII50A-SF Bedienungsanleitung

Bradford White

Bradford White EverHot TGHE-160I-NX Service-Handbuch

Bradford White

Bradford White UPV75 Series Bedienungsanleitung

Bradford White

Bradford White HE440S*F Bedienungsanleitung

Bradford White

Bradford White URG2PV75H N Series Bedienungsanleitung

Bradford White

Bradford White UPV Series Bedienungsanleitung

Bradford White

Bradford White Magnum D75T125E3N Bedienungsanleitung

Bradford White

Bradford White M-2-50T6DS Bedienungsanleitung

Bradford White

Bradford White M1TW40S Series Bedienungsanleitung

Bradford White

Bradford White 100T399-SOLA Betriebsanleitung

Bradford White

Bradford White 355-B Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung