Bradford White URG2PV75H6N-475-264 Bedienungsanleitung

238-51010-00E REV 5/18

POWER VENT GAS WATER HEATER

A Spanish language version of these instructions is available by contacting the

company listed on the rating plate.

La version espanola de estas instrucciones se puede obtener al escribirle a la

fabrica cuyo nombre aparece en la placa de especificaciones.

WHAT TO DO IF YOU SMELL GAS

 Do not try to light any appliance.

 Do not touch any electrical switch; do not use any

phone in your building.

 Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier's instructions.

 If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by a qualified

installer, service agency or the gas supplier.

For your family’s comfort, safety and convenience we

recommend this water heater be installed and serviced by a

plumbing professional.

INSTALLATION AND OPERATION

INSTRUCTION MANUAL

FOR YOUR SAFETY

Do not store or use gasoline or other flammable,

combustible, or corrosive vapors and liquids in the

vicinity of this or any other appliance.

WARNING: If the information in these instructions is not

followed exactly, a fire or explosion may result causing

property damage, personal injury, or death.

CONGRATULATIONS!

You have just purchased one of the finest water heaters on the

market today!

This installation, operation and instruction manual will explain in

detail the installation and maintenance of your new Power Vent

Gas Water Heater. We strongly recommend that you contact a

plumbing professional for the installation of this water heater.

We require that you carefully read this manual, as well as the

enclosed warranty, and refer to it when questions arise. If you

have any specific questions concerning your warranty, please

consult the plumbing professional from whom your water heater

was purchased. For your records we recommend that you write

the model, serial number and installation date of your water

heater in the maintenance section in the back of this manual.

This manual should be kept with the water heater.

TABLE OF CONTENTS

page

GENERAL INFORMATION ................................................................. 4

INSTALLATION. .................................................................................. 5

Locating the Water Heater .......................................................... 5

Minimum Clearances ................................................................... 8

Venting .......................................................................................... 8

Vent Pipe Preparation and Joining ............................................ 19

Combustion Air Supply ............................................................... 21

Water Connections ...................................................................... 23

Gas Connections .......................................................................... 26

Electrical Connections ................................................................ 27

Wiring Diagram ...................................................................... 28

GENERAL OPERATION ..................................................................... 29

Lighting and Shutdown Instructions ......................................... 30

Thermostat Adjustment ............................................................... 31

Burner Flame Check .................................................................... 32

MAINTENANCE ................................................................................... 33

TROUBLESHOOTING ......................................................................... 36

PARTS LIST AND DRAWING ............................................................. 38

INSTALLATION INSTRUCTIONS FOR POTABLE WATER AND

SPACE HEATING ................................................................................ 39

NOTES ................................................................................................. 40

GENERAL INFORMATION

This gas-fired water heater’s design is certified by CSA International under the

American National Standard Z21.10.1, CSA 4.1-M, Z21.10.3 and CSA 4.3 most

current editions at the time of manufacture. This is a category III water heater.

This water heater must be installed in accordance with local codes or, in the

absence of local codes, the National Fuel Gas Code, ANSI Z223.1-Latest

Edition) and/or in Canada CAN/CGA B149 Installation Codes (Latest Editions).

The warranty for this water heater is in effect only when the water heater is

installed, adjusted, and operated in accordance with these Installation and

Operating Instructions. The manufacturer will not be held liable for any damage

resulting from alteration and/or failure to comply with these instructions.

This water heater is not design certified for installation in a mobile home. Such

an installation may create a hazardous condition and will nullify the warranty.

Do not use this appliance if any external part to the tank has been submerged in

water. You should contact a qualified service technician to inspect the appliance

and to replace any part of the control system including the combination gas

control which has been submerged in water. See the Gas Connections section

of this manual before servicing or replacing a water heater that has had any

external part to the tank submerged in water.

CAUTION

Incorrect operation of this appliance may create a hazard to life

and property and will nullify the warranty.

WARNING

Prior to connecting the gas supply line to a gas fired water heater,

ensure that the gas supply line does not have moisture/water or

dirt/scale inside the gas line. Commonly this check is done at the

lowest point in the gas distribution system prior to gas burning

appliances.

DANGER

Do not store or use gasoline or other flammable, combustible, or

corrosive vapors and liquids in the vicinity of this or any other

appliance.

General Information continued-

Make sure that you check the rating plate and combination gas control on the

water heater to be certain that the type of gas being supplied corresponds with

the marking on the rating plate and combination gas control.

A sacrificial anode(s) is used to extend tank life. Removal of any anode, except

for inspection and/or replacement, will nullify the warranty. In areas where water

is unusually active, an odor may occur at the hot water faucet due to a reaction

between the sacrificial anode and impurities in the water. If this should happen,

an alternative anode(s) may be purchased from the supplier that installed this

water heater. This will minimize the odor while protecting the tank. Additionally,

the water heater should be flushed with appropriate dissolvers to eliminate any

bacteria.

INSTALLATION

Locating The Water Heater

DO NOT install the water heater in any location where gasoline or

flammable vapors are likely to be present.

Water Heaters in residential garages must be installed so that all burner(s)

and burner ignition device(s) are located not less than 18 inches (46 cm)

above the floor and must be located or protected to avoid physical

damage. For other installations refer to local codes. In the absence of

local codes, the water heater must be installed in compliance with the

National Fuel Gas Code, ANSI Z223.1 - (Latest Edition) and/or in Canada,

CAN/CGA B149 Installation Codes (Latest Editions).

Installation (Locating The Water Heater) continued-

IMPORTANT

Before proceeding, please inspect the water heater and its components for

possible damage. DO NOT install any water heater with damaged

components. If damage is evident then please contact the supplier where the

water heater was purchased or the manufacturer listed on the rating plate for

replacement parts.

WARNING

Water heaters are heat producing appliances. To avoid damage or

injury, do not store materials against the water heater or vent-air intake

system. Use proper care to avoid unnecessary contact (especially by

children) with the water heater and vent-air intake components. UNDER

NO CIRCUMSTANCES MUST FLAMMABLE MATERIALS, SUCH AS

GASOLINE OR PAINT THINNER BE USED OR STORED IN THE

VICINITY OF THIS WATER HEATER, VENT-AIR INTAKE SYSTEM

OR IN ANY LOCATION FROM WHICH FUMES COULD REACH THE

WATER HEATER OR VENT-AIR INTAKE SYSTEM.

The location of this water heater is of the utmost importance. Before installing

this water heater, read the installation section of these instructions. After

reading these installation and operating instructions, select a location for the

water heater where the floor is level and is easily accessible to gas and water

supply lines. DO NOT locate the water heater where water lines could be

subjected to freezing temperatures. Make sure the cold water pipes are

not located directly above the gas control so that condensate during

humid weather does not drip on the controls.

Water heater corrosion and component failure can be caused by the heating

and breakdown of airborne chemical vapors. Examples of some typical

compounds that are potentially corrosive are: spray can propellants, cleaning

solvents, refrigerator and air conditioning refrigerants, swimming pool

chemicals, calcium and sodium chloride, waxes and process chemicals. These

materials are corrosive at very low concentration levels with little or no odor to

reveal their presence. NOTE: DAMAGE TO THE WATER HEATER CAUSED

BY EXPOSURE TO CORROSIVE VAPORS IS NOT COVERED BY THE

WARRANTY. DO NOT OPERATE THE WATER HEATER IF EXPOSURE HAS

OR WILL OCCUR. DO NOT STORE ANY POTENTIALLY CORROSIVE

COMPOUNDS IN THE VICINITY OF THE WATER HEATER.

To comply with NSF requirements this water heater is to be:

a) Sealed to the floor with sealant, in a smooth and easily cleanable way,

b) Installed with an optional leg kit that includes legs and/or extensions

that provide a minimum clearance of 6” beneath the water heater.

WARNING

Liquefied petroleum gases/propane gas are heavier than air and will

remain at floor level if there is a leak. Basements, crawl spaces,

closets, and areas below ground level will serve as pockets for

accumulation of leaking gas. Before lighting, smell all around the

appliance area for gas. Be sure to smell next to the floor.

IF YOU SMELL GAS:

 Do not try to light any appliance.

 Do not touch any electric switch; do not use any telephone in

your building.

 Immediately call your gas supplier from a neighbor’s telephone.

Follow the gas supplier’s instructions.

 If you cannot reach your gas supplier, call the fire department.

DO NOT OPERATE APPLIANCE UNTIL THE LEAKAGE IS

CORRECTED!

Installation (Locating The Water Heater) continued-

The water heater must be located close enough to the outside wall to keep the

venting distance within the maximum distance described in the installation

instructions. Locate the water heater as close as possible to the vent opening.

Read the venting section in this installation instruction manual before locating

the water heater.

This water heater must be located in an area where leakage of the tank or water

line connections and the combination temperature and pressure relief valve will

not result in damage to the area adjacent to the water heater or to lower floors

of the structure. When such locations cannot be avoided, a suitable drain pan

adequately piped for proper drainage must be installed under the water heater.

The pan must not restrict combustion air flow. The drain pan must have a

minimum length and width of at least 4 in. (10.2 cm) greater than the diameter

of the water heater and must not restrict proper combustion air flow to the water

heater. The drain pan, as described above, can be purchased from your

plumbing professional. The drain pan must be piped to an adequate drain. The

piping must be at least 3/4 inch (1.9 cm) in diameter and pitched for proper

drainage.

It is recommended that a minimum clearance of 4 inches (10.2 cm) be provided

on the side of the water heater for servicing and maintenance of the

combination temperature and pressure relief valve.

This water heater MUST be installed indoors out of the wind and weather.

Note: For California installation this water heater must be braced,

anchored, or strapped to avoid falling or moving during an earthquake.

See instructions for correct installation procedures. Instructions may be

obtained from DSA Headquarters Office, 1102 Q Street, Sacramento, CA

95811.

WARNING

DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE IF YOU ARE

NOT CERTAIN OF THE FOLLOWING:

 Liquefied petroleum gases/propane gas and natural gas have an

odorant added by the gas supplier that aids in the detection of the

gas.

 Most people recognize this odor as a “sulfur” or “rotten egg” smell.

 Other conditions, such as “odorant fade” can cause the odorant to

diminish in intensity, or “fade”, and not be as readily detectable.

 If you have a diminished sense of smell, or are in any way unsure of

the presence of gas, immediately contact your gas supplier from a

neighbor’s telephone.

 Gas detectors are available. Contact your gas supplier, or plumbing

professional, for more information.

Minimum Clearances

This installation must allow access to the front of the water heater and adequate

clearance must be provided for servicing and operating this water heater. The

water heater may be installed on either a combustible or non-combustible floor.

If the water heater is to be installed directly on carpeting, it must be installed on

top of a metal or wood panel extending beyond the full width and depth of the

appliance by at least 3 inches (7.6 cm) in any direction or, if the appliance is to

be installed in an alcove or closet, the entire floor must be covered by the panel.

The minimum clearances to combustibles for this water heater are: 0 inch from

the sides and rear, 5 inches (12.7 cm) from the front of the jacket, 0 inch from

the vent connector and 15 inches (38.1 cm) from the jacket top. Increase

distances to provide clearance for servicing.

Venting

Figure 1 - Vent Terminal Clearances

WARNING

Failure to adhere to these installation and operating

instructions may create a hazard to life and property and will

nullify the warranty.

Venting continued-

Canadian Installations

US Installations

A= Clearance above grade,

veranda, porch, deck or

balcony

12 inches

(30 cm)

12 inches

(30 cm)

B= Clearance to window or

door that may be

opened

6 in. (15 cm) for appliances

≤ 10,000 Btuh (3 kW), 12 in.

(30

cm) for appliances > 10,000

Btuh (3 kW) and

≤100,000 Btuh

(30 kW), 36 in. (91 cm) for

appliances >100,000 Btuh

(30 kW))

4 ft (1.2 m) below or to

side of opening; 1 ft (300

mm) above opening

C= Clearance to

permanently closed

window

*b *b

D= Vertical clearance to

ventilated soffit located

above the terminal

within a horizontal

distance of 2 feet (.6 m)

from the center line of

the terminal

*b *b

E= Clearance to

unventilated soffit

*b *b

F= Clearance to outside

corner

*b *b

G= Clearance to inside

corner

*b *b

H= Clearance to each side

of center line extended

above meter/regulator

assembly

3 feet (.9 m) within a height

15 feet (4.6 m) above the

meter/regulator assembly

I= Clearance to service

regulator vent outlet or

oil tank vent

3 feet (.9 m) *b

J= Clearance to non-

mechanical air supply

inlet to building or the

combustion air inlet to

any other appliance

12 inches

(30 cm)

4 feet (1.2m) below or to

side of opening;

12 inches (30 cm) above

opening.

K= Clearance to a

mechanical air supply

inlet

6 feet

(1.83 m)

3 feet (91 cm) above if

within 10 feet horizontally

L= Clearance above paved

sidewalk or paved

driveway located on

public property

7 feet

(2.13 m)†

7 feet

(2.13 m)†

M= Clearance under a

veranda, porch, deck, or

balcony

12 inches

(30 cm) ‡

1 In accordance with the current CAN/CGA-B149 Installation Codes.

2 In accordance with the current ANSI Z223.1-(Latest edition)/NFPA 54 National Fuel Gas Code.

† A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single-family

dwellings and serves both dwellings.

‡ Permitted only if a veranda, porch, deck or balcony is fully open on a minimum of two sides beneath the floor.

*a) A minimum clearance value determined by testing in accordance with section 5.21.1 of ANSI Z21.10.1 latest

edition.

*b) “Clearance in accordance with local installation codes and the requirements of the gas supplier”.

This water heater has a certified category III, per latest ANSI Z 21.10.3-

2015.CSA 4.3-2015 revision. Refer to the latest edition of the National Fuel

Gas Code (ANSI Z223.1-latest edition), or in Canada, the Natural Gas and

Propane installation Code (B149.1-00 latest edition).

Venting continued-

The vent system must terminate so that proper clearances are maintained as

cited in local codes or the latest edition of the National Fuel Gas Code, ANSI

Z223.1.73.4e and 7.8a, b as follows:

1. Do not terminate near soffit vents or crawl space or other area where

condensate or vapor could create a nuisance or hazard or cause property

damage.

2. Do not terminate the exhaust vent terminal where condensate or vapor

could cause damage or could be detrimental to the operation of regulators,

relief valves, or other equipment.

3. Do not terminate the exhaust vent terminal over public area or walkways

where condensate or vapor can cause nuisance or hazard.

4. The vent shall terminate a minimum of 12 inches (25.4 cm) above expected

snowfall level to prevent blockage of vent termination.

Vent pipes serving power vented appliances are classified by building codes as

“vent connectors”. Required clearances from combustible materials must be

provided in accordance with information in this manual under LOCATION OF

WATER HEATER and CLEARANCES, and with National Fuel Gas Code and

local codes.

WARNING

Risk of carbon monoxide poisoning or fire due to joint separation or

pipe breakage.

This water heater must be properly vented and connected to an approved

vent system in good condition. DO NOT operate water heater with the

absence of an approved vent system. A clean and unobstructed vent system

is necessary to allow noxious fumes that could cause injury or loss of life to

vent safely and will contribute toward maintaining the water heater’s

efficiency. The acceptance of the venting system is dependent upon full

compliance with these installation instructions.

Venting system must not pass through rated fire separations.

The venting system must be free to expand and contract. This venting

system must be supported in accordance with these instructions.

Clearance to combustibles for all venting pipes and terminals

For installations in the US

0” minimum

For installations in Canada

Refer to vent pipe and terminal

manufacturer’s installation instructions

for clearances to combustibles

DO NOT place insulation or other materials in the required clearance spaces

between the venting to combustible material unless otherwise specified.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradford White Boiler Handbücher

Bradford White

Bradford White ElectriFLEX LD LE Series Bedienungsanleitung

Bradford White

Bradford White UPV75 Series Bedienungsanleitung

Bradford White

Bradford White PDX1-40S6FBN Beilage

Bradford White

Bradford White GX225S BN Series Bedienungsanleitung

Bradford White

Bradford White TW Series Bedienungsanleitung

Bradford White

Bradford White S-SW2-60R6DS Bedienungsanleitung

Bradford White

Bradford White BRUTE DELUXE BMT2H Bedienungsanleitung

Bradford White

Bradford White ElectriFLEX HD CEHD50 Bedienungsanleitung

Bradford White

Bradford White Defender Safety System 238-48248-00 Konfigurationshandbuch

Bradford White

Bradford White VR-150-(kW) Handbuch

Bradford White

Bradford White BNTH Bedienungsanleitung

Bradford White

Bradford White 238-37281-00R Beilage

Bradford White

Bradford White EFT-28000-4-T-10 Bedienungsanleitung

Bradford White

Bradford White EverHot TGHE-160E-NX Service-Handbuch

Bradford White

Bradford White ASME Bedienungsanleitung

Bradford White

Bradford White EFTM Montageanleitung

Bradford White

Bradford White EFT-5500-4-S-10 Bedienungsanleitung

Bradford White

Bradford White MI30T*F(BN Bedienungsanleitung

Bradford White

Bradford White Copper Brute II BWCH 2000 Bedienungsanleitung

Bradford White

Bradford White RE1 Bedienungsanleitung

Bradford White

Bradford White RE340T6 Betriebsanleitung

Bradford White

Bradford White Combi2 TTW C-DW2-TW50T10FBN Bedienungsanleitung

Bradford White

Bradford White GAS-FIRED WATER HEATER Bedienungsanleitung

Bradford White

Bradford White DH1504T* Anwendungshandbuch

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung