Bradley Aerada 900 Series Bedienungsanleitung

Installation

P.O. Box 309

Menomonee Falls, WI 53052 USA

800 BRADLEY (800 272 3539)

+1 262 251 6000

bradleycorp.com

Aerada™ 900 Series

With Accu-Zone®(AZ) Infrared Control

Table of Contents

Supplies Required ...............................2

Dimensions and Configurations.....................2

Installation .....................................3

Multi-Faucet Wiring ..............................4

Replacing the Sensor ............................5

Troubleshooting .................................5

S53-341TL - 4" Centerset

S53-341TMA - 4" Centerset w/ TMV

S53-343TL - Centershank

S53-343TMA - Centershank w/TMV

S53-345TL - 4" Centershank w/8" Trim Plate

S53-345TMA - 4" Centershank w/ 8" Trim Plate, TMV

WARNING

Make sure that all water supply lines have been flushed and then completely turned off before beginning

installation. Debris in supply lines can cause valves to malfunction.

CAUTION

A DC plug-in adapter (supplied by Bradley) should be used in conjunction with the 900 Series Futura (AZ)

Faucets. The DC plug-in adapter supplied by Bradley is 12V DC regulated. Direct connection to 120V/220V

50/60Hz could result in personal injury and will damage the sensor.

IMPORTANT

Read this entire installation manual to ensure proper installation. When finished with the installation, file

this manual with the owner or maintenance department. Compliance and conformity to local codes and

ordinances is the responsibility of the installer.

Separate parts from packaging and make sure all parts are accounted for before discarding packaging

material. If any parts are missing, do not begin installation until you obtain the missing parts.

When the faucet is mounted on a fixture with a stainless steel bowl, it is recommended that the bowl have a

satin finish rather than a mirrored or highly polished finish.

Product warranties may be found under “Products” on our web site at bradleycorp.com.

215-1680 Rev. D; ECN 16-02-004

Page 1 of 6 11/18/2016

Aerada 900 Series Faucet Installation

11/18/2016 Bradley • 215-1680 Rev. D; ECN 16-02-004

Supplies Required

• 120V/220V 50/60Hz power source using Bradley supplied 120VAC/12V DC plug-in adapter

• Tempered hot and cold supply piping and fittings to solenoid valve (1/2" NPT)

• 1/4" O.D. tubing

• Pipe fittings, pipe sealant as required

Dimensional Information

Centershank Mounting Centerset Mounting

(178)

(102)

Washer

3/4" (19)

Drilled Hole

Copper Tubing

Nut

3/8" (10)

Drilled Hole

1-1/8" (29)

Drilled Hole

Nut &

Washer

Faucet Stud

Copper Tubing

(203)

1-1/8"

(29)

Flow Control

Aerator Assy.

(S05-142A)

Adapter

(153-467)

Sensor

Window

(269-604)

Accu-Zone Sensor

Fitting Assy.

(S05-193)

Faucet Components

Centershank

Faucet Shown

Mounting Configurations

Centerset Mounting

Ref. Part No. Description

1 110-115 Mounting Nut

2 112-002CB Mounting Washer

3 161-151 8" Trimplate

Mounting Screw

4 S27-224 Mounting Prepack

5 159-399 8" Trimplate

6 161-078

Sensor Bracket Nut

7 142-002BS Sensor Bracket

Washer

8 - Sensor Bracket

9 269-1184-DC Accu-Zone Sensor

10 160-169 Sensor Mounting

Screw

Centershank Mounting

Parts List

2-5/16"

(58)

(mm)

Installation Aerada 900 Series Faucet

Bradley • 215-1680 Rev. D; ECN 16-02-004 11/18/2016

Cold Inlet

1/2" NPT

Hot Inlet

1/2" NPT

1/4" O.D. Tubing

(Supplied by Installer)

(30" max. length, IPC,

section 604.5; UPC,

section 604.12)

Solenoid

Valve

TMA Navigator®

Shown

Centershank

Faucet Shown

Mount Faucet on Deck

Deck

Centerset

Faucet

Shown

Washer

Nut

ADrill holes in deck to the size and position

for your faucet configuration, as shown on

previous page.

BAttach faucet and trim plate (if applicable)

securely to deck. Seal around faucet and

trim plate with plumber's putty.

Connect Water and Electrical Supply

120VAC/12V DC

Plug-In Adapter

For units equipped with a TMA Navigator

Mixing Valve, complete steps 3 and 4 of this

installation manual.

Connect Faucet Harness

Connector to Mating

Connector on Solenoid Valve

Aerada 900 Series Faucet Installation

11/18/2016 Bradley • 215-1680 Rev. D; ECN 16-02-004

Multi-Faucet Wiring

One plug-in adapter operates up to four

faucets at one time. Additional plug-in

adapter(s) are required for installations

with more than four faucets.

DO NOT SKIP THIS STEP!!!

This valve is NOT factory preset. Upon installation, the temperature of this valve must be checked and adjusted

to ensure delivery of a safe water temperature. Water in excess of 110°F (43°C) may cause scalding.

This step only applies for units equipped with a TMA Navigator Mixing Valve.

Adjust Temperature with Running Water

ALoosen cap screw about 1/4" (4-6 turns)

and lift up cover (do not remove).

Using cover, turn cartridge gently until

desired water temperature is reached. Do

not turn past stops as this may damage

unit. Push cover down and tighten screw.

Test Unit

This step only applies for units equipped with a TMA Navigator Mixing Valve.

Shut the hot water inlet off by closing

hot water inlet valve. While the hot water

supply is turned off, check to make sure

the cold water flow is reduced. If the cold

water is reduced properly, reopen the hot

water supply.

Shut the cold water inlet off by closing

the cold water inlet valve. While the cold

water supply is off, check to make sure

that the hot water flow has shut down.

Installation Aerada 900 Series Faucet

Bradley • 215-1680 Rev. D; ECN 16-02-004 11/18/2016

Replacing the Sensor CAUTION To avoid personal injury and/or damage to the faucet,

TURN OFF the electrical power and water BEFORE

beginning any cleaning, troubleshooting or maintenance.

NOTICE! Sensor must be flush and parallel with the lens.

Do not force or bend the bracket!

Troubleshooting – Solenoid Valve

Problem Cause Solution

Faucet fails to shut off and drips. The cartridge valve is defective. Replace cartridge.

Faucet fails to turn on. A failed valve or loose electrical

connection to the connectors.

1. Repair loose connection.

2. If possible, determine whether sensor, power adapter

or valve is defective by swapping parts with an adjacent

faucet. Replace defective part.

Ref. Part No. Description

1 118-334 Valve Body

2 S27-352 Cartridge

3 125-165 O-Ring, #2-013

4* 125-160 Flow Restrictor, .5 GPM

Parts List for S07-068-DC

Centerset Mounting

Centershank Mounting

Accu-Zone

Sensor

Bracket

* Not included with S07-068-DC.

S07-068-DC

Disconnect the faucet harness

connector from the solenoid

valve and remove the faucet from

the deck.

Following the illustrations at right

for your faucet configuration,

remove the screws and /or

nuts holding the bracket, then

carefully remove the bracket and

sensor assembly from the faucet

shell.

Remove screws securing the

existing sensor to bracket.

Installation of the new sensor is

the reverse process.

Aerada 900 Series Faucet Installation

11/18/2016 Bradley • 215-1680 Rev. D; ECN 16-02-004

Before attempting to troubleshoot the valve or disassemble the components, check for the following conditions:

• If stop valves are used, make sure that they are fully open.

• Make sure that the hot and cold inlet pipes are connected properly, and that there are no cross-

connections or leaking stop valves.

• Check the hot water heater output to make sure that it is at least 10° F above the set temperature.

Troubleshooting – Thermostatic Mixing Valve

Close the appropriate shut-off valves prior to disassembly and reopen valves after inspection and

repair is complete.

Problem Cause Solution

External leaks. Damaged cartridge or

O-rings.

Replace cartridge with part number 269-1927

Improper water temperature or

temperature fluctuation.

Hot water supply is not 10°

above desired set point.

Increase hot water supply temperature

Valve temperature is not

properly set.

Adjust the temperature as shown on page 4 step 3.

Limited water flow. Dirt and debris have built

up in the valve or strainer.

1. Check to make sure both hot and cold supplies are connected to the

Navigator mixing valve and that they have water flow.

2. Remove cover and U-clip. Remove the cartridge and clean the

strainer. It is not required to grease cartridge, however if desired, use

silicone grease only.

Do not use grease on check valves.

Ref. Part No. Description

1 160-463 Cap Screw

2 107-582 Cover

3 269-1927 Thermostatic Cartridge

4 198-014 Check Valve*

5 132-051 Retaining Ring*

6 146-079 U-Clip

7 118-319 Valve Body

* Included with Prepack S65-326

6Strainer

173-028

Tempered Line Adapter Option:

Part no. S39-804

Parts List for S01-526

S01-526

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley SN2013 Bedienungsanleitung

Bradley

Bradley TouchTime MG Series Bedienungsanleitung

Bradley

Bradley Verge LVQ Series Bedienungsanleitung

Bradley

Bradley S19-310PVC Bedienungsanleitung

Bradley

Bradley S19-270HD Bedienungsanleitung

Bradley

Bradley Express ELX-3 Bedienungsanleitung

Bradley

Bradley Aerada 90-80 Series Bedienungsanleitung

Bradley

Bradley S19-430EFW Bedienungsanleitung

Bradley

Bradley LC800 Bedienungsanleitung

Bradley

Bradley HN-400 Bedienungsanleitung

Bradley

Bradley Terreon Classic WF2500 Series Bedienungsanleitung

Bradley

Bradley CRS Series Bedienungsanleitung

Bradley

Bradley S19-220FW Bedienungsanleitung

Bradley

Bradley Terreon TDB3104 Bedienungsanleitung

Bradley

Bradley Express ELX Series Bedienungsanleitung

Bradley

Bradley Verge Crestt Series Bedienungsanleitung

Bradley

Bradley S19-310BF Bedienungsanleitung

Bradley

Bradley S19-120FMBF Bedienungsanleitung

Bradley

Bradley Express SS Series Bedienungsanleitung

Bradley

Bradley S96-050 Bedienungsanleitung

Bradley

Bradley Express ELX Series Bedienungsanleitung

Bradley

Bradley S96-085 Bedienungsanleitung

Bradley

Bradley P19-234 Bedienungsanleitung

Bradley

Bradley Sentry SN2008/IR Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema