Braun EXACTFIT 1 Bedienungsanleitung

English......................................... 2

Polski............................................ 11

Čeština ........................................ 20

Magyar........................................ 29

Română....................................... 38

Slovenčina ................................. 47

Braun ExactFit™1

BUA5000

Upper arm blood pressure monitor

Intended use of Braun ExactFit™ 1

Braun ExactFit™ 1 is a blood pressure monitor that has been developed

for easy and accurate blood pressure measurements from the upper arm.

The measuring accuracy of Braun ExactFit™ 1 was tested at the time of

manufacture and was proven by clinical research in accordance with

ESH.†

What youshould know about blood pressure

Blood pressure constantly changes throughout the day. It rises sharply in

the early morning and declines during the late morning. Blood pressure

rises again in the afternoon and nally drops to a low level at night. Also,

it may vary in a short period of time.Therefore, readings from successive

measurements can uctuate.

This device will display your blood pressure reading referring to two

values: systolic and diastolic.The systolic blood pressure (the upper

number) indicates how much pressure your blood is exerting against

your artery walls when the heart beats.The diastolic blood pressure (the

lower number) indicates how much pressure your blood is exerting

against your artery walls while the heart is resting between beats.The

pulse value is also displayed after each measurement.

Blood pressure measured in a doctor’s oce only provides a momentary

value. Repeated measurements at home better reect one’s actual blood

pressure values under everyday conditions.

Moreover, many people have a dierent blood pressure when they

measure at home, because they tend to be more relaxed than when in

the doctor’s oce. Regular blood pressure measurements taken at home

can provide your doctor with valuable information on your normal blood

pressure values under actual «everyday» conditions.

The ESH (European Society of Hypertension) and WHO (World Health

Organisation) have set up the following standard blood pressure values

when measured with a resting pulse at home:

Avoid compression or restriction of the connection tubing. Continuous

cu pressure due to the connection tubing kinking can aect blood ow

and cause possible injury to the user.

It is not recommedned to use this device on the arm of the same side of

the body on which the user had a mastectomy.

Measuring blood pressure too frequently can cause injury to the user due

to blood ow interference.

It is not recommended to apply the cu to a limb on which there is

intravasular access or on which an arterio-venous (A-V) shunt is present.

This can cause temporary interference of blood ow and potential injury

to the user.

DO NOT apply the cu over a wound as this can cause further injury.

GB English

It is not recommended to use the device while simultaneously using

other medical electrical (ME) equipment on the same lmb.

†European Society of Hypertension

Safety information and important precautions

To ensure accurate measuring results, read the complete instructions for

use carefully.

People suering from cardiac arrhythmia, vascular constriction,

arteriosclerosis in the extremities, diabetes or users of cardiac

pacemakers should consult their doctor before measuring their blood

pressure themselves. Deviations in blood pressure values may occur in

such cases.

If your blood pressure reading is in the severe hypertension range with

values of 180 mmHg systolic and above, and/or 110 mmHg diastolic and

above; and you nd you have one or two readings in this range - please

see your doctor straight away.

If you are under medical treatment or taking any medication, please

consult your doctor rst.

The use of this blood pressure monitor is not intended as a substitute for

a consultation with your doctor.

Product description

1LCD display

2Power (start/stop) button

3Hose port

4Battery compartment

5Connector

6Arm cu

7Air hose

Blood

pressure

(mmHg)

Normal

values

Grade 1

mild

hypertension

Grade 2

moderate

hypertension

Grade 3

severe

hypertension

SYS = systole

(upper value) up to 134 135-159 160-179 ≥180

DIA = diastole

(lower value) up to 84 85-99 100-109 ≥110

English

Inserting batteries

•Use alkaline batteries, type AA 1.5V

as supplied with this product.

•Remove the battery compartment cover

and insert four batteries with correct

polarity (see symbol in the battery

compartment).

Batteries should not be disposed of in

the household waste, but at appropriate collection sites or at

your retailer.

Key rules for accurate blood pressure measurement

Always take readings at the same timeof day, under the same conditions.

Do not take a measurement within 30 minutes of smoking, drinking

coee or tea or any form of exertion.These factors will inuence the

measurement.

Ensure at least 5 minutes of quiet rest before measurements. If possible, it

is recommended to rest 10 minutes before taking the measurement.Try

to always use the same resting time before taking a measurement.

Always measure on the same arm.The left arm is recommended. Do not

move or speak. Keep your legs uncrossed and feet at on the oor.

Place the cu in direct contact with the skin. Do not wrap the cu over a

jacket, sweater or shirt.

If you want to take multiple measurements, wait approximately

3 minutes before repeating a measurement.

Applying the arm cuff

1. Plug the air hose into the connector (Fig. 1).

2. The cu is located correctly when the velcro is on the outside of the

cu and the metal ring does not touch the skin (Fig. 2).

3. Put your arm through the cu loop.The bottom of the cu should be

Pile side material

Velcro

Smooth

cloth Metal ring

2-3 cm

Left arm

Fig. 1 Fig. 2 Fig. 3

approximately 2-3 cm above elbow (Fig. 3).The tube should lie over

the brachial artery on the inside of the arm (Fig. 4).

Adult cu

22-42 cm

Artery mark

Main arteries

Fig. 4 Fig. 5 Fig. 6

4. Pull the cu so that the top and bottom edges are tightened around

your arm.

5. When the cu is positioned properly, press theVelcro rmly against

the pile side of the cu.

6. This cu is suitable for use if the arrow heads fall within the stripe

pattern on the other side of the cu when the cu is tightened

around your arm (Fig. 5).

7. Sit on a chair and place your arm on the table so that the cu is at the

same level as your heart (Fig. 6).

Taking a measurement

8. Sit on a chair with your feet at on the oor.

9. Wrap the cu snugly around your arm

(see“Applying the arm cu”section above,

Fig. 3-6).

10. Do not move the unit during measurement,

or the proper measurement will not be

achieved.

11. Press power button to begin.The measurement starts

automatically.While measurement is in progress, do not move or

speak.

Note: If necessary to interrupt a measurement, press the power

button at any time.The device immediately cancels the

measurement, lowers cu pressure and automatically turns o.

12. The cu will rst inate and then deate. At the end of the

measurement there are 2 nal beep sounds and the reading is

displayed:

Upper (systolic) value

Lower (diastolic) value

Pulse

13. Press the power button to turn the product o. Otherwise the

product will turn o automatically after 1 minute.

English

14. Test results will be saved into the memory automatically ( see

memory function below).

This device is not intended as a substitute for regular check-ups by your

doctor, please continue to visit your doctor on a regular basis for a

professional reading.

Memory function

Your ExactFit™ 1 blood pressure monitor will automatically store the

latest measurement. Storing is done automatically after the completed

measurement.

To recall the reading, press and hold the power button for at least

4 seconds while the unit is switched o.When all the display elements

are shown, release the power button and the screen will show the last

reading with an symbol.

Battery charge indicator

Batteries almost discharged

When the batteries are approximately 75%

used, a battery warning appears.This icon

blinks 3 times rst when the device is turned

on, then goes to measuring mode.The

monitor will continue to measure reliably, but

new batteries should be obtained.

Batteries discharged—replacements required

When the batteries are fully discharged,

the battery symbol will ash empty along

with 3 short beep sounds as soon as the

device is switched on.You cannot take any

further measurement and must replace

the batteries. Refer to the section called

“Inserting batteries”.

Storage and cleaning

•Do not expose device to either extreme temperatures, humidity, dust

or direct sunlight.

•The cu contains a sensitive air-tight inatable bladder. Handle this

carefully and avoid all types of straining through twisting or buckling.

•Clean the device with a soft dry cloth. Stains on the cu can be

carefully removed with a damp cloth. Do not use gasoline, thinners or

similar solvents. Do not wash or dry clean the cu. Do not store the

product in a place exposed to direct sunlight or high humidity.

•Do not drop the device or treat it roughly in any way. Avoid strong

vibrations.

•NEVER open the device!This will make the manufacturer’s warranty

invalid and could adversely aect the device’s accuracy!

Calibration

This product has been calibrated at the time of manufacture. If used

according to the instructions for use, periodic recalibration is not

required. If at any time you question the measuring accuracy, please

contact our service representative (see last page for contact information).

What to do if ...

Error Description Potential cause and remedy

Batteries are low Get ready to replace batteries soon with

new ones.

Batteries are fully

discharged Insert new batteries or check that

batteries are correctly inserted.

«Err 1» Signal too weak The pulse signals on the cu are too

weak. Re-position the cu and repeat

the measurement.

«Err 2» Error signal During the measurement, error signals

were detected by the cu, caused for

instance by movement or muscle

tension. Repeat the measurement,

keeping the arm still.

«Err 3» No pressure in the

cu An adequate pressure cannot be

generated in the cu. A leak may have

occurred. Check that the cu is correctly

connected and is not too loose. Replace

the batteries if necessary. Repeat the

measurement.

«Err 5» Abnormal result The measuring signals are inaccurate

and no result can therefore be

displayed. Read through the checklist

for performing reliable measurements

and then repeat the measurement.

«HI» Pulse or cu

pressure

too high

The pressure in the cu is too high (over

300 mmHg) OR the pulse is too high

(over 200 beats per minute). Relax for

5 minutes and repeat the measurement.

«Lo» Pulse too low The pulse is too low (less than 40 beats

per minute). Repeat the measurement.

English

Error Description Potential cause and remedy

Readings from

repeated

measurements dier

considerably.

Blood pressure is a

uctuating value.

For healthy adults,

deviations of 10 to

20 mmHg are possible.

Reminder: always use the same arm

for measurements!

Cu is not properly

tted. Ensure that the cu is tted

according to the“Applying the arm

cu”section.

Readings were not

consistently taken at

heart level.

For each measurement, make sure

that the cu is at heart level.

Talking, coughing,

laughing, moving etc.

when measuring will

inuence the reading.

While measuring, relax, keep still,

do not move or speak.

Blood pressure values

measured at your

doctor’s oce dier

from your

measurements.

Doctor visits can

frequently cause

anxiety.

Record the daily development of

the measured values and consult

your doctor.

Display remains

blank, or is unusual,

when instrument is

switched on.

Batteries are not

installed properly. Check batteries for correct polarity.

Device frequently

fails to measure

blood pressure

values, or values

measured are too low

(or too high).

Cu may not be

properly positioned. Ensure that the cu is tted

according to the“Applying the arm

cu”section.

Andere Handbücher für EXACTFIT 1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Braun Blutdruckmessgerät Handbücher

Braun

Braun ExactFit 5 Bedienungsanleitung

Braun

Braun PrecisionSensor Pro BP 2590 Instructions Bedienungsanleitung

Braun

Braun VitalScan 5 Bedienungsanleitung

Braun

Braun BP6000 Bedienungsanleitung

Braun

Braun ActivScan 9 Bedienungsanleitung

Braun

Braun PrecisionSensor BP 2550 Bedienungsanleitung

Braun

Braun ExxactFit 5 Bedienungsanleitung

Braun

Braun VitalScan 1 Bedienungsanleitung

Braun

Braun EXACTFIT 1 Bedienungsanleitung

Braun

Braun EXACTFIT 1 Bedienungsanleitung

Braun

Braun BP4900 Bedienungsanleitung

Braun

Braun ExactFit 3 Bedienungsanleitung

Braun

Braun ExactFit 5 Bedienungsanleitung

Braun

Braun ExactFit 3 Bedienungsanleitung

Braun

Braun EXACTFIT 1 Bedienungsanleitung

Braun

Braun ActivScan 9 Bedienungsanleitung

Braun

Braun SensorControl Easy Click Bedienungsanleitung

Braun

Braun EXACTFIT 1 Bedienungsanleitung

Braun

Braun BP 3510 Bedienungsanleitung

Braun

Braun BP4000 Bedienungsanleitung

Braun

Braun ExactFit 5 Bedienungsanleitung

Braun

Braun VITALSCAN BP1000 Bedienungsanleitung

Braun

Braun BP4900 Montageanleitung

Braun

Braun SensorControl BP 2550 Bedienungsanleitung

Beliebte Blutdruckmessgerät Handbücher anderer Marken

Little Doctor

Little Doctor LD7 Bedienungsanleitung

Microlife

Microlife WatchBP Office Targe Bedienungsanleitung

Omron

Omron M6W Handbuch

Mx Onda

Mx Onda MX-CP2395 Bedienungsanleitung

Little Doctor

Little Doctor LD-91 Bedienungsanleitung

Sanitas

Sanitas SBM 09 Bedienungsanleitung

A&D

A&D LifeSource UB-328 Bedienungsanleitung

König Electronic

König Electronic HC-BLDPRESS200 Bedienerhandbuch

Leicke

Leicke Sharon Bedienungsanleitung

Omron

Omron M6 Comfort Bedienungsanleitung

3B SCIENTIFIC

3B SCIENTIFIC U11395 Bedienungsanleitung

Soehnle

Soehnle SYSTO MONITOR 100 Bedienungsanleitung

Nasco Healthcare

Nasco Healthcare Simulaids Life/form LF01095U Referenzhandbuch

Microlife

Microlife WatchBP office Bedienungsanleitung

HoMedics

HoMedics MiBody 360 Bedienungsanleitung

ForaCare

ForaCare FORA P30 Plus Bedienungsanleitung

JOYTECH

JOYTECH DBP-6296B Bedienungsanleitung

Omron

Omron Silver BP5250 Bedienungsanleitung