Braun Exact Power EP 100 Bedienerhandbuch

Service Documentation Market Release 10/99

Braun exact power EP 100, 80, 60 5601

5601

5601 - 2

BINC Rev: 9/99 Service Documentation

Exploded Drawing

BAG Rev: 9/99 5601

5601 - 3

BINC Rev: 9/99 Service Documentation

Spare Parts List

BAG Rev: 9/99 5601

Pos. No. Part Description Part Number

1Comb attachment 5601621

2Cutter set 5601622

3Small parts set 5601623

4Swivel frame 5601632

5Housing front part (silver) 5601633

6Motor 5601624

7PCB (1 hr) 5601625

8Housing back part 5601634

Coiled cord 5002704

Cleaning brush 5503120

Case 7000062

5601 - 4

BINC Rev: 9/99 Service Documentation

Service Information

BAG Rev: 9/99 5601

Technical Data Principle Rechargeable / cord shaver

Nominal voltage 120 VAC

Nominal frequency 50 - 60 Hz

Housing Plastic material

Cutting system Switchable double cutting system

(21 resp. 33 mm width)

Switch function Central sliding switch with integrated "speed"-shifting

and button for lock function

Separate memory slide for 7 beard-length positions

(1 - 2 - 3 - 6 - 9 - 12 and 16 mm)

Drive 1.2 V DC motor

Revolutions switchable to two positions

Position 1: approx. 4.760 r.p.m. (min.)

approx. 6.120 r.p.m. (max.)

Position 2: approx. 5.600 r.p.m. (min.)

approx. 6.800 r.p.m (max.)

(after a recharging time of least 3 minutes and with

greased cutting system)

Power transmision Via eccenter directly onto the shaving system

Power supply Via a built in, rechargeable NH-battery, resp. a built-in

battery recharger

Charging time EP 100 approx. 1 hour

EP 80 approx. 8 hours

EP 60 approx. 16 hours

Power consumption EP 100 approx. 4 watts

EP 80 approx. 5 watts

EP 60 approx. 1,35 watts

Charging of the shaver Is indicated by a green lamp

Operating capacity after full recharge

approx. 30 cutting minutes

5601 - 5

BINC Rev: 9/99 Service Documentation

Service Information

BAG Rev: 9/99 5601

Dismantling Comb attachment (1) Set sliding switch in "0" position.

Pull off comb attachment by snap action.

Cutter set (2) To be snapped out by pressing buttons "A".

Swivel frame (4) Insert a small Torx screwdriver into the hole of the

springs (3a) and snap them out by pushing towards the

inside of the frame. Remove the pin (3b).

Unhinge and remove swivel frame (4) (see diagram

below).

Housing Unscrew screw "B" (3c) of the housing back part (8).

Press together the housing front part (5) in the area of

the bearing pin; then, insert a wide-bladed screwdriver

into the guide slot on the left side of the sliding switch

and unhinge the housing snaps. Now, pull apart the

housing halves.

Motor (6) Remove the screw (3c) in the housing font part (5).

Unsolder the connecting wires to the PCB (7).

PCB (7) Remove and snap out plug connector.

5601 - 6

BINC: 9/99 Service Documentation

Service Information

BAG: 9/99 5601

Reassembly The reassembly is done in reversed order.

Please pay attention to the following points:

Motor (6) Insert the motor (6) into the housing front part (5) in

such a way that the indentations for the swivel head

snaps on the left side of the cover point towards the

memory slider. Then, fix with screw (3c).

PCB (7) Before inserting the PCB, please make sure that the

contact slider is placed correctly into the connecting-

link, gripping into the carrier of the memory slider.

Press the connecting plug into the supporting clamps of

the socket housing. Insert the PCB.

Solder the connecting wires to the motor; pay attention

to the correct poles!

(Solder the plus wire (red) to the motor connection

marked with a red dot).

Housing When pressing together the housing halves (5 + 8), the

guides of the central and memory switches must grip

into the housing lower part.

Screw the screw (3d) into the housing back part.

Swivel frame (4) Insert the swivel frame (4) into the pick-ups, the spring

notch "C" being on the side of the memory slider.

Insert the pin (3b).

Push the springs (3a) onto the pins (3b) from the

frame's inside.

5601 - 7

BINC: 9/99 Service Documentation

Service Information

BAG: 9/99 5601

Hint To facilitate the reassembly of the springs (3a), and

nail (head dia. 4 mm) can be clamped in a vice, the

device being supported with the pin head (see diagram).

Cutter set (2) Press buttons "A" and insert them; pay attention to the

correct sides.

Check functions.

Checking the PCB

•Let the shaver run empty from normal operation.

•Connect to power supply. (Depending on the shaver version, the power

consumption is approx. 1 - 5 watts).

•Recharge shaver approx. 5 minutes. (The green lamp must burn permanently).

•Disconnect shaver from the mains and measure voltage via battery.

The voltage of the cell must exceed 1.2 V. If this value is indicated, the PCB is

in order.

Maintenance note To maintain the optimum cutting performance of the beard trimmer and the

optimum life of the battery it is absolutely necessary to clean and to grease the

cutter set (2) regularly.

Please proceed as follows:

•Unlock and remove cutter set by pressing buttons "A".

•Clean with the brush.

•Apply a drop of resin-free oil (e.g. sewing machine oil) between the cutters

and the sliding spring bearings in the back.

•Reassemble the cutter set and check the electrical function.

Attention Used batteries must not be disposed of in the household waste, but at

appropriate disposal sites.

Andere Handbücher für Exact Power EP 100

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Braun Elektrorasierer Handbücher

Braun

Braun 8970 Bedienungsanleitung

Braun

Braun BG5030 Bedienungsanleitung

Braun

Braun Tricontrol 4775 Bedienungsanleitung

Braun

Braun Silk epil X'elle 5580 Bedienungsanleitung

Braun

Braun Series 1 Bedienungsanleitung

Braun

Braun 190cb-1 Bedienungsanleitung

Braun

Braun Silk & Soft LS 5100 Bedienungsanleitung

Braun

Braun 390CC-3 Bedienungsanleitung

Braun

Braun 170s Bedienungsanleitung

Braun

Braun 5696 Bedienungsanleitung

Braun

Braun SIK EPIL 7 Bedienungsanleitung

Braun

Braun 790cc-7 Bedienungsanleitung

Braun

Braun BT 5030 Bedienungsanleitung

Braun

Braun cruzer 6 Bedienungsanleitung

Braun

Braun DigiFrame 1008 Bedienungsanleitung

Braun

Braun 5708 Bedienungsanleitung

Braun

Braun 9 Pro 9470CC Bedienungsanleitung

Braun

Braun Cruzer 2675 Bedienungsanleitung

Braun

Braun 750CC-5 Bedienungsanleitung

Braun

Braun Syncro 7546 Bedienungsanleitung

Braun

Braun Flex Integral + 5446 Bedienungsanleitung

Braun

Braun Silk.epil 3470 Bedienungsanleitung

Braun

Braun 5474 Bedienungsanleitung

Braun

Braun 6 Series Bedienungsanleitung

Beliebte Elektrorasierer Handbücher anderer Marken

Philips

Philips MicroAction 4402LC Bedienungsanleitung

Philips

Philips HQ7740 Bedienungsanleitung

Philips

Philips Norelco BG2022 Bodygroom Bedienungsanleitung

Norelco

Norelco Quadra 7610X Bedienungsanleitung

Philips

Philips 7616X Bedienungsanleitung

Philips

Philips HQ802 Bedienungsanleitung

Philips

Philips HQ7363/17 Bedienungsanleitung

Philips

Philips NORELCO S7371 Bedienungsanleitung

Daga

Daga MT-400 Handbuch

Remington

Remington BHT100 Bedienungsanleitung

Philips

Philips Bodygroom BG2000 Bedienungsanleitung

Kompernass

Kompernass KH 5537 Bedienungsanleitung

Remington

Remington BHT6100 Bedienungsanleitung

Philips

Philips qc5365 Bedienungsanleitung

MIA

MIA Aqua Body Bedienungsanleitung

Philips

Philips NORELCO AT880 Bedienungsanleitung

Matheo

Matheo MLR 15 Bedienungsanleitung

Remington

Remington XR7000 Bedienungsanleitung