BraunAbility ULB Bedienungsanleitung
Seat Lockers
User Manual
EN Instructions for tting and use
2ULB, ULS
Thank you for choosing
Seat Lockers
from BraunAbility!
The following manual is an important part of the product, providing
you with information on how to achieve maximum performance
and safe operation. Keep the manual in a safe place so that you can
refer to it when necessary.
If you have any questions about your equipment, please contact us.
Once again, thank you for placing your condence in our products!
Safe vehicle adaptation solutions
For your safety BraunAbility products are
designed and tested according to current
directives and standards.
Safety information
Fit and use
After care
Limitations of use
Fitting the Seat Locker to the seat leg
Operating the Seat Locker
Equipment storage and maintenance
Warranty
4
6
8
10
10
3
ULB, ULS
EN
Index
“Declaration of conformity” at the end of the manual.
Limitation of use
Safety information
4ULB, ULS
Black Seat Locker (ULB) Grey Seat Locker (ULS)
5
ULB, ULS
EN
Safety information
Fitting Seat Locker to seat legs
Fit and use
Note: Two removable seat xtures are normally required for each seat. It is important that the seat
legs are set to the identical rail width where the seat is to be tted. Both Seat Locker need to be
aligned parallel to each other in the rail.
1. First remove M10 nyloc nuts and washers from the front sliding stud assembly with a 17mm wrench.
Then remove the bolts and washers from the rear of the unit using an 8mm allen key (Fig 1).
2. Place the seat on the Seat Locker, ensuring that the seat is placed facing towards the front of the
vehicle. Fit sliding studs through the front seat leg bracket holes (Fig 2). Then t the rear seat leg
bracket position to the appropriate xture’s hole (Fig 3). Note: Depending on the seat design, the
third bolt may not be required.
3. Replace all washers, nuts and bolts and loosely fasten with an 8mm allen key at the rear of the
lockable (Fig 4) and 17mm wrench at the front (Fig 5). We recommend tightening the rear bolts
rst to ensure correct positioning of the seat. Finally tighten M10 nyloc nuts and bolts with a torque
wrench to a recommended torque of: 35-40Nm (18-22lb/ft)
WARNING
If it is intended that the seat should face the rear, please contact BraunAbility.
6ULB, ULS
123
45
7
ULB, ULS
EN
Fit and use
Operating the Seat Locker
Fit and use
Fitting the seat into the rail
1. Before locating the seat into the rail, ensure the Seat Locker handles are in the
fully raised positions.
2. To locate the seat in the rail, align both Seat Locker wheels into the rail, tilt the
seat backwards slightly and wheel it along the rail to the right location
(Fig 6 & 7) . Once this is found, lower the seat into the rail gently push it
forwards or backwards until it is located into the rail, ensuring the front of the
Seat Locker is at with the rail surface (Fig 8).
3. Press the Seat Locker handle gently with your foot until a click is heard (Fig 9).
Removing the seat from the rail
1. To release the seat from the rail, push
the Seat Locker silver release buttons
forward and lift the handles upwards
(Fig 10).
2. Pull the seat rearwards at the lowest
point of the seat leg until the handles
are in a fully raised position (Fig 11).
3. Tilt the seat backwards slightly and
remove it from the rail (Fig 12).
8ULB, ULS
678
9
10 11 12
9
ULB, ULS
EN
Fit and use
Equipment storage and maintenance
After care
Regularly inspect the Seat Locker for damage, wear or malfunction.
If any problems are identied replace immediately.
Warranty
BraunAbility products are extensively tested using BraunAbility anchorage systems, and our full warranty
normally only applies to BraunAbility equipment when used with BraunAbility branded anchorages or as
instructed.
BraunAbility have also participated in test programs with other manufacturers anchorage products and will
support warranty on the BraunAbility products when used in conjunction with such jointly tested systems.
For further details on specic applications please contact the Sales Ofce. In other situations, using
BraunAbility products, for which BraunAbility has not participated in a joint test program, a limited
BraunAbility warranty will apply.
10 ULB, ULS
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere BraunAbility Autozubehör Handbücher
BraunAbility
BraunAbility EntervanII Anwendungshandbuch
BraunAbility
BraunAbility Pedal Extension Mini Bedienungsanleitung
BraunAbility
BraunAbility Entervan XT Handbuch
BraunAbility
BraunAbility Carolock Bedienungsanleitung
BraunAbility
BraunAbility Simple Stow Bedienungsanleitung
BraunAbility
BraunAbility Foldout Ramp Handbuch
BraunAbility
BraunAbility Rampvan Handbuch
BraunAbility
BraunAbility Simple Stow Bedienungsanleitung
BraunAbility
BraunAbility Kit 6 Bedienungsanleitung
BraunAbility
BraunAbility Simple Stow Infloor Bedienungsanleitung
