Brightek C03 Gebrauchsanweisung
QUICK INSTALL
快速安装
北京炜煌科技发展有限公司
Beijing Bright Technology Development Co.,Ltd
C03
快速安装手册
http://www.whkj.com.cn 010-51655555
●打印机各部件一览 Printer Parts Names
1.LF 键/电源指示灯 LF Button/ Power Light
2.打印头 Printer head
3.纸仓 Paper Case
4.紧固件 Fastener
5.纸仓盖 Paper Case Cover
6.滚轴/切刀 Platen
Roller/Cutter
7.纸仓开关 Lock
8.接地 Ground
9.电源接口 Power Connector
10.SET 键 SET Button
11.USB 接口 USB Connector
12.数据接口 Interface Connector
13.固定架 Holder
快速安装手册
http://www.whkj.com.cn 010-51655555
●尺寸 Size
按钮开关的操作及指示灯
电源指示灯常亮为正常状态，状态指示灯闪烁为缺纸。
正常上电后，按 LF 键走纸。按任意键上电，根据不同提示进行打印机设置。
自检测方式
打印机上电之后，按住 LF 键不放，同时给打印机上电，即打出自检条。
Operation Specification
After turning on the printer, the indicator light will keep on. When
the light flash, it shows that the paper is lacking, and the printer
can not receive data.
After turning on the printer, press the LF button, the printer will
feed paper, and the SET button is no used.
The Self Test
Press the LF button, do not release and repower the printer at the
same time，and then the printer will print out the self-check scrip.
快速安装手册
http://www.whkj.com.cn 010-51655555
●连接 Connection
安装方法：
请把打印机嵌入部分插入仪器或设备面板的安装孔内,并把塑料卡子从设备面板后面夹紧
打印机，螺钉从前面穿入并与塑料卡子中的螺母连接拧紧，左右对称各一套，安装方法相
同。
所安装的面板厚度为 0.5～6mm 厚的金属板或塑料板;厚薄不会影响打印机安装的牢固性。
开口尺寸：117mm+0.5×103mm+0.5
Installation Method
Insert the built-in part of printer into the installing orifice of instrument or
equipment. As the picture show, fix the fastener onto the printer and tighten the
screws in front of panel.
The faceplate that will be fixed could be metal plate or plastic plate with
thickness from 0.5mm to 6mm. Neither too thick nor too thin would affect the
fastness of the printers.
Installation dimension:117mm+0.5×103mm+0.5.
快速安装手册
http://www.whkj.com.cn 010-51655555
●装纸 Paper Roll
通讯连接：
请严格参照公司网站提供产品说明书进行连接。
电源连接：
WH 微打随机提供的一根带有插头的两线电源电缆,插头具有极性保护机构,电源电缆的红
色线接电源正极(+),另一线接电源负极(-)。
注意:不要将交流 220V 与打印机电源插座直接相连，工作电压应在额定电压
±5%以内,电源极性一定要接正确,否则会给打印机造成永久性损坏,炜煌公
司对此不承担保修义务。
Communication Connection
Please refer to the printer manual on company website.
Power Connection
Notice the power cable, connect the red cord to positive pole, connect the white
cord to the negative pole.
Attention： Do not connect AC to the printer directly, operating voltage should
be within ±5% rated voltage. Power polarity must be correct, otherwise it will
cause permanent damage to printer, brightek company do not assume maintenance
compulsory upon this.
快速安装手册
http://www.whkj.com.cn 010-51655555
●清洁 Cleaning
安装步骤：
1.如图 1 箭头位置按下开关按钮，这时打印头走纸轴、切刀与打印头分离，轻轻拉开纸仓
盖，使纸仓盖彻底打开。
2.装入打印纸，并拉出一截(超出一点撕纸牙齿)，把纸放整齐，同时注意纸的方向，有药
液一面(光滑面)向上(如图 3)。
3.合上纸仓盖，打印头走纸轴压齐打印纸后稍用力把打印头走纸轴压回打印头(如图 4)
4.接通打印机的电源，按键使机头转动，这时看一下纸是否走歪，待机，或关上电源。
Replacing the Paper Roll
1. Press the button which arrow point to as shown in Fig 1, and undrawn the paper
cover.
2. Insert the paper into the printer, Pull out a small amount of paper. Notice
the direction of the paper according to Fig.3.
3. Close the paper cover. Press the platen roller back to the printer head.
4. Power the printer on, then press LF button, make the print head to run, and
the paper will come out. Turn off the power.
快速安装手册
http://www.whkj.com.cn 010-51655555
清洁保养：
热敏打印机使用久了以后，热敏条与滚轴上会留下一些污垢，如果不及时清理会影响到打
印机的使用与寿命。我们建议您不定期做好清理。
纸舱盖打开后，用棉棒沾少许酒精，轻轻擦拭打印机热敏头，及纸仓上的滚轴。
Printer Cleaning
If the interior of the printer is dusty, print quality can decline. So please clean
the printer regularly. Open the cover of printer, then Wipe the print head with
a cleaning pen and Use a cloth moistened with an alcohol solution to clean the
paper sensor and the platen roller.
●产品规格一览表 Product Specification
项目 ITEMS
规格 SPECIFICATION
打印方式 Printing method
Thermal printing method
纸宽 Paper width
80mm
打印宽度 Print width
72mm
分辨率 resolution ration
576dots/line
打印头寿命 life of printing head
6,000,000 character lines
打印速度 Printing speed
65mm/sec(when the utilization rate is 25%)
字符大小 Character size
6x8dots, 8x16dots, or 12x24dots
汉字库 Chinese character library
GB2312, 16x16dots, or 24x24dots
纸的规格 Paper supplied
80mm wide,50mmø
接口 Interface
Serial(RS232C,TTL)/USB interface
输入电源 Input power
DC 9-24V
操作温度 Operating temperature
5℃～50℃
存储温度 Storage temperature
-20℃～60℃
操作湿度 Operating humidity
10%～80%
存储湿度 Storage humidity
10%～90%
Inhaltsverzeichnis
Andere Brightek Drucker Handbücher
Brightek
Brightek C2 Gebrauchsanweisung
Brightek
Brightek M06 Gebrauchsanweisung
Brightek
Brightek A6 Gebrauchsanweisung
Brightek
Brightek E21 Gebrauchsanweisung
Brightek
Brightek E39 Gebrauchsanweisung
Brightek
Brightek E17 Gebrauchsanweisung
Brightek
Brightek E22 Gebrauchsanweisung
Brightek
Brightek E27 Gebrauchsanweisung
Brightek
Brightek E26 Gebrauchsanweisung
Brightek
Brightek A9 Gebrauchsanweisung
Brightek
Brightek E44 Gebrauchsanweisung
Brightek
Brightek E19 Gebrauchsanweisung
Brightek
Brightek E32 Gebrauchsanweisung
Brightek
Brightek E16 Gebrauchsanweisung
Brightek
Brightek E55 Gebrauchsanweisung
Brightek
Brightek U02 Gebrauchsanweisung
Brightek
Brightek C05 Gebrauchsanweisung
Brightek
Brightek A3 Gebrauchsanweisung
Brightek
Brightek A7 Gebrauchsanweisung
Brightek
Brightek U04 Gebrauchsanweisung
