Bristan Claret CLR BASNW C/WHT Montageanleitung

Installation Instructions

and User Guide

Claret Tap Range

Models Covered:

CLR BASNW C/WHT

CLR 1HBF C/WHT

CLR WMBAS C

CLR WMBF C/WHT

CLR WMBSM C

Please keep this booklet for future

reference.

Installer, when you have read these

instructions please ensure you leave

them with the user.

2Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Thank you for choosing Bristan, the UK’s leading taps and showers expert.

We have designed this product with your enjoyment in mind. To ensure that it works

to its full potential, it needs to be ﬁtted correctly. These ﬁtting instructions have been

created to give you all of the information you need and, if you need any further help,

please do not hesitate to contact us.

Contents

• Important Safety Information 3

• Speciﬁcations 4

• Dimensions (mm) 5-6

• Installation 7-12

• Maintenance 13-14

• Troubleshooting 15

Contents

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Important Safety Information

• Please read these instructions thoroughly

and retain for future use.

• All products manufactured and supplied

by Bristan are safe provided they are installed,

used correctly and receive regular maintenance

in accordance with these instructions.

• If you are in any doubt about your ability

to install this product safely you must employ

the services of an experienced qualiﬁed

plumber/electrically qualiﬁed person.

• This product has been tested to the Water

Regulations Advisory Scheme (WRAS) and

satisﬁes the requirements of the Water Supply

(Water Fittings) Regulations 1999 and current

bylaws. For full Installation Requirements &

Notes (IRN) please visit wras.co.uk/directory.

• Warning: Before starting

any installation please consider the

following: before drilling into walls, check that

there are no hidden electrical wires, cables or

water supply pipes. This can be checked with

the aid of an electronic detector.

• If power tools are used do not forget to:

- Wear eye protection

- Unplug equipment after use

• Important: Remember to turn o the mains

water supply before connecting to any existing

pipe work.

• Warning: Before installing

the new ﬁtting it is essential that

you thoroughly ﬂush through the pipework in

order to remove any remaining swarf, solder,

etc. Failure to carry out this procedure could

cause problems or damage to the workings of

the ﬁtting.

• We recommend isolation valves to be ﬁtted to

the inlet water supplies to ensure ease of future

maintenance.

• Full access must be made available for future

maintenance/servicing purposes.

• Take care when handling the ‘ﬂexible

connecting pipes’, do not bend, twist or crush

them. Only tighten the pipes by hand.

• Do not crush or kink the shower hose, this

could damage the hose and cause leaks.

This product must not be modiﬁed in any way as

this will invalidate the guarantee.

If in doubt, contact a registered plumber or your

Local Water Authority or the Secretary of the

Institute of Plumbing, address as follows:-

The Institute of Plumbing,

64 Station Lane,

Hornchurch,

Essex,

RM12 6NB, Tel: 01708 472791

4Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Speciﬁcations

Product Code Working Pressure

Min Max

1 Hole Bath Filler 1.5 5.0

Basin Mixer (No waster) 0.2 5.0

Wall Mounted Basin Mixer 1.0 5.0

Wall Mounted Basin Filler 0.3 5.0

Wall Mounted Bath Shower

Mixer

1.0 5.0

Maximum static pressure- 10.0 bar

NOTE:- Nominally equal (balanced) inlet supply pressures are recommended for

optimum Performance of mixer taps.

Designed to comply with BS EN 200 for single taps/ combination taps for water

systems of type 1 and 2 general technical speciﬁcations; and to be used within

systems designed to BS 6700.

BS 6700 recommends the temperature of stored water should never exceed

65° C. A stored water temperature of 60° C is considered sucient to meet all

nominal requirements and will minimise the build up of lime scale in hard water

areas.

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Dimensions (mm)

170

105

175

125

60 55

Basin Mixer

1 Hole Bath Filler

6Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Dimensions (mm)

50 60

190

127

122

180

330

120

197

145

100 100

220

147

185

50 62

182

100

128

122

120

100

210

110

100

5040

20150

140

118

115 40

Wall Mounted Basin Mixer

Wall Mounted Bath Filler

Wall Mounted Bath Shower Mixer

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation

1. Identify all components are present

prior to starting installation.

2. Ensure that the washer (9) is ﬁtted

to the underside of the tap body

(7) before ﬁtting to the basin/bath.

Secure the ‘C’ shaped rubber washer

(10) and metal plate (11) into position

on the underside of the basin/bath,

using the threaded rods and nuts

(12).

3. Fit the inlet connection pipes (13) by

hand only (DO NOT OVERTIGHTEN)

to the ﬁtting and connect the hot

and cold supplies.

4. Connect the hot and cold water

supplies to the connecting pipes.

5. Turn on the water and fully open

the mixer, allowing it to run for a

few minutes and check all joints and

connections for any leaks.

Basin Mixer (No Waste) & 1 Hole

Bath Filler

1. Grub Screw x1

2. Lever Handle x1

3. Lever Handle Spacer x1

4. Shroud x1

5. Cartridge Retaining Nut x1

6. Cartridge x1

7. Tap Body x1

8. Anti-Splash Assembly x1

9. Washer x1

10. ‘C’ Shaped Rubber Washer x1

11. ‘C’ Shaped Metal Plate x1

12. Fixing Rods x2

13. Connecting Pipes x2

8Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation Cont.

Wall Mounted Basin Mixer/ Bath

Filler

1. Handle x1

2. Cartridge Retaining Nut x1

3. Shroud x1

4. Cartridge x1

5. Mixer Body Sleeve x1

6. O-Ring x1

7. Mixer Body x1

8. Concealing Plate x1

9. Concealing Plate x1

10. O-Ring x1

11. O-Ring x1

12. Screw & Wall Plug Pack x1

13. Nut & Olive x1

14. Spout Connection Kit x1

15. Locking Grub Screws x2

16. Spout Grub Screw x1

17. Spout x1

18. Anti-Splash x1

19. Handle Grub Screw x1

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation Cont.

1. Identify all components are present

prior to starting installation using

the diagram overleaf, and be sure to

refer to the dimensions on pages 4

& 5 for minimum and maximum wall

cavity depths.

2. Oer the mixer body (7) up to the

wall and once in the desired position,

mark and drill holes for the ﬁxings

(12)

IMPORTANT: Before drilling into walls,

check that there are no hidden electrical

wires, cables or water supply pipes.

This can be checked with the aid of

an electronic detector. If power tools

are used do not forget to wear eye

protection & unplug equipment after

use.

3. Fit the mixer body (7) to the wall

and connect water supplies using the

nut and olive (13). Any further tiling

required, should be completed at this

stage.

NOTE: The tiles should not restrict

access to the valve in order to allow for

servicing of the product if necessary.

4. Push concealing plate (8). complete

with seal (9), over the valve body and

push towards the tiled surface.

TIP: Use a thin line of silicone based

sealant around the back edge of the

concealing plate to create a tight water

seal.

5. Push the spout (17) on to the pre-

ﬁtted spout connection kit (14);

ensuring that both O-rings locate

within the spout, and both of the

locking grub screws (15) ﬁt into

place, via the 2 small holes in the

concealing plate (8). Tighten grub

screw on the underside of spout to

secure into place.

6. Turn on the water and fully open

the mixer, allowing it to run for a

few minutes and check all joints and

connections for any leaks

Wall Mounted Basin Mixer/ Bath Filler

10 Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation Cont.

Wall Mounted Bath Shower Mixer

1. Handle x1

2. Shroud x1

3. Retaining Nut x1

4. Cartridge x1

5. Sleeve x1

6. 0-Ring x1

7. Mixer Body x1

8. Concealing Plate x1

9. Plate Seal x1

10. 0-Ring x1

11. O-Ring x1

12. Handset Holder x1

13. Hose x1

14. Handset x1

15. Spout Connections x1

16. Spout Locking Pins x1

17. Spout x1

18. Grub Screw x1

19. Anti-Splash x1

20. Diverter Assembly x1

21. Diverter Knob x1

22.Grub Screw x1

23.Screw & Wall Plug Pack x1

24.Nut & Olive x3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bristan Küchen- und Badezimmerausstattung Handbücher

Bristan

Bristan Prism PM 3HWMBAS C Bedienungsanleitung

Bristan

Bristan CAS BAS C Bedienungsanleitung

Bristan

Bristan MINI2 TS1203 CL C Montageanleitung

Bristan

Bristan Oval Series Bedienungsanleitung

Bristan

Bristan TO DSM C Bedienungsanleitung

Bristan

Bristan QD 1/2 C Verdrahtungsschema

Bristan

Bristan GWF BF C Verdrahtungsschema

Bristan

Bristan AR SNKPURE C Bedienungsanleitung

Bristan

Bristan Java Series Verdrahtungsschema

Bristan

Bristan Acute AE 1/2 C Bedienungsanleitung

Bristan

Bristan Java Bedienungsanleitung

Bristan

Bristan Regency R2 SHXAR C Montageanleitung

Bristan

Bristan W SNK5C Verdrahtungsschema

Bristan

Bristan Nero Series Bedienungsanleitung

Bristan

Bristan Club DUC HNK C Bedienungsanleitung

Bristan

Bristan Pear PEA PULLSNK C Verdrahtungsschema

Bristan

Bristan GLL RAPSNK3 C Montageanleitung

Bristan

Bristan Liquorice LQR PROSNK C Verdrahtungsschema

Bristan

Bristan Capri Bedienungsanleitung

Bristan

Bristan Kingsbury Verdrahtungsschema

Bristan

Bristan 1901 Bedienungsanleitung

Bristan

Bristan Quest QST 1/2 C Verdrahtungsschema

Bristan

Bristan FH TDRD01 C Bedienungsanleitung

Bristan

Bristan AR THBSM C Bedienungsanleitung

Beliebte Küchen- und Badezimmerausstattung Handbücher anderer Marken

Grohe

Grohe BRIDGEFORD 33 870 Bedienungsanleitung

Hans Grohe

Hans Grohe Zenio Metro 31811000 Bedienungsanleitung

Gröne

Gröne Zedra 32 555 Bedienungsanleitung

Transform

Transform QL045 Bedienungsanleitung

Sanela

Sanela SLU 09PTB Bedienungsanleitung

Glacier bay

Glacier bay FP4A0052BNV Montageanleitung

Lefroy Brooks

Lefroy Brooks C1-1400 Montageanleitung

Grohe

Grohe Rapido E Bedienungsanleitung

Danze

Danze D302455 Bedienungsanleitung

Waterworks

Waterworks CEKM30 Merkblatt

Helvex

Helvex Omega TV-298 Bedienungsanleitung

Tribata.

Tribata. GEORGIAN G5393 Bedienungsanleitung

Alpha Bidet

Alpha Bidet Alpha One Bedienungsanleitung

InSinkErator

InSinkErator H/HC3300 Installationshandbuch

Clou

Clou Xo type 1 Bedienungsanleitung

Kohler

Kohler Contra 26448T-4 Bedienungsanleitung

Grohe

Grohe Bridgeford 20 158 Bedienungsanleitung

Hans Grohe

Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Bedienungsanleitung