Bristan QD 1/2 C Verdrahtungsschema

Installation Instructions &User Guide

Please keep these instructions for future reference and request of replacement parts

Quadrato Basin & Bath Tap Range

Installation Instructions & User Guide

Contents

Thank you for choosing Bristan, the UK’s leading taps and showers expert. We

have designed this product with your enjoyment in mind. To ensure that it

works to its full potential, it needs to be fitted correctly. These fitting

instructions have been created to give you all of the information you need and, if

you need any further help, please do not hesitate to give us a call on 0330 026

6273.

Important Safety Information 03

General Specifications 03

Installation Requirements 04-07

Installation 07-12

Basin &Bath Ta ps 07

Small Basin Mixer 08

Eco Basin Mixer 09

Eco Basin Mixer (Without Waste) 09

Tall Basin Mixer 10

Bidet Mixer 11

Bath Filler 12

Bath Shower Mixer 12

Maintenance 13

Troubleshooting 14

Guarantee 15

Important Safety Information

•Please read these instructions thoroughly and retain for future use.

•All products manufactured and supplied by Bristan are safe provided they are

installed, used correctly and receive regular maintenance in accordance with these

instructions

•If you are in any doubt about your ability to install this product safely

you must employ the services of an experienced qualified plumber.

•Remove all packaging and check the components for damage before

starting installation.

•Before starting any installation please consider the following: Prior to

drilling into walls, check that there are no hidden electrical wires, cables or

water supply pipes. This can be checked with the aid of an electronic detector.

•If power tools are used do not forget

to:

- Wear eye protection

-Unplug equipment after

use

•This product must not be modified in any way as this will invalidate the guarantee.

•These fittings need to be installed in accordance with and meet the requirements of the

Water Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.

General Specifications

Operating pressure range (bar) Min Max

Basin &Bath Taps 0.2 8.0

Small Basin Mixer 0.5 8.0

Eco Basin Mixer 0.5 8.0

Tall Basin Mixer 0.4 8.0

Bidet Mixer 0.5 8.0

Bath Filler 0.3 8.0

Bath Shower Mixer 0.5 8.0

Maximum static pressure –10.0 bar

NOTE:-Nominally equal (balanced) inlet supply pressures are recommended for

optimum performance.

Designed to comply with BS EN 200 for single taps/ combination taps for water

systems of type 1 and 2general technical specifications and to be used within systems

designed to BS 6700.

BS 6700 recommends the temperature of stored water should never exceed 65°C. A

stored water temperature of 60°Cis considered sufficient to meet all nominal

requirements and will minimise the build up of lime scale in hard water areas.

Installation Requirements

IMPORTANT - PLEASE READ

This/these fitting/fittings needs/need to

be installed in accordance with the

following Installation Requirements and

Notes (IRN) to ensure they meet the

requirements of the Water Supply (Water

Fittings) Regulations 1999 and the

Scottish Byelaws 2004.

IRN R001 -QD ½ C, QD ¾ C, QD SMBAS C,

QD EBAS C, QD EBASNW C, QD TBAS C, QD

BF C, QD BSM C

See text of entry for Installation

Requirements or Notes.

IRN R005 -QD BF C, QD BSM C

This tap or combination tap assembly has a

Type AUK2 air gap and is therefore only

suitable for installation in domestic premises

or in other premises to protect against a

backflow risk up to a Fluid Category 3, unless

additional backflow protection for the higher

risk is included in the installation.

IRN R030 -QD BSM C -Schedule 2-15 (1)

Multiple inlet fittings installed in domestic

premises or in other premises to protect

against a backflow risk up to a Fluid

Category 3, incorporating a self cancelling

diverter acceptable as a backflow

prevention device (HC) and having an

AUK2 or AUK3 air gap, shall be installed

in accordance with IRN R010.

Multiple inlet fittings installed in premises

other than domestic to protect against a

backflow risk up to a Fluid Category 5,

incorporating a self cancelling diverter

acceptable as a backflow prevention

device (HC only) and having an AUK2 or

AUK3 air gap, shall be installed in

accordance with IRN R010. Alternatively

the fitting shall be supplied in accordance

with IRN R040 unless the shower head is

constrained above the spill-over lever of

the bath, wash basin or shower tray.

IRN R006 -QD ½ C, QD ¾ C, QD SMBAS C,

QD EBAS C, QD EBASNW C, QD TBAS C

This tap or combination tap assembly has a

Type AUK3 air gap and is therefore for

installation in any premises to protect against

a backflow risk up to a Fluid Category 5.

IRN R010 – QD SMBAS C, QD EBAS C, QD

EBASNW C, QD TBAS C, QD BF C

Schedule 2-15 (1)

Water supplies shall be a reasonably

balanced pressures from a common source

(e.g. hot and cold supplies both from the

same storage or both from a supply pipe).

Where the fitting is supplied from

unbalanced supplies (e.g. hot and cold

supplies from separate sources) a ‘Listed’

single check valve or some other no less

effective backflow prevention device shall

be fitted immediately upstream of both hot

and cold water inlets.

IRN R070 –QD BID C

The water supply (Water Fittings)

Regulations 1999 and the Water Bylaws

2000, Scotland preclude the

connection of rim feed ascending spray

type bidets with hand –held spray

attachments directly to any supply

pipe.

Continued overleaf.

AUK2 or AUK3 air

gap as

appropriate

Washbasin,

sink or bath

Single check valves if

required

Cold water

supply

Hot water

supply

Combination tap: -

Cutaway section

showing cold and

hot water mixing in

the body of the tap

Diagram 1

BIDETS WITH OVER-RIM SUPPLY ARRANGEMENTS

(a) Bidets installed in domestic locations of

the over –rim type, that have no

ascending spray and/or flexible hose

may be supplied with cold and hot water

through single or combination tap

assemblies from either a supply pipe or

distributing pipe providing that a Type

AUK2 air gap is provided between the

outlet of the water fitting and the

spillover level of the bidet and shall also

comply with (c) below.

(a) Bidets installed in premises other than

domestic locations of the over –rim

type, that have no ascending spray and

/ or flexible hose where a higher fluid

category of risk may be present, may

be supplied

with cold and hot water through single or combination tap assemblies from either a

supply pipe or a distributing pipe providing that a Type AUK3 air gap is provided

between the outlet of the water fitting and the spillover level of the bidet as (a)

above and shall also comply with (c) below.

also be installed in accordance with IRN R010. See Diagram 1 below

Bidets, including WCs adapted as bidets,

incorporating and ascending spray inlet or

utilising a flexible hose or an arrangement with

a spray or jet, are a fluid category 5 risk in

that the ascending spray inlet could be

contaminated with urine or other matter and

the spray or jet handset could be deposited in

the bidet or WC. Bidets of this type must not

be supplied with water from a cold or hot

water supply pipe or a common distributing

pipe. The zone of backflow risk is shown and

the highest part of this zone must be not less

that 15mm below any cistern serving the

bidet. See Diagram 2 below. 05

Hose and spray

Bidet

Independent

distributing

pipes for cold

and hot water

Zone of

backflow risk

Not less than 15mm

air gap

BIDETS (INCLUDING WCS ADAPTED AS BIDETS) WITH SUBMERGED

WATER INLETS AND /OR FLEXIBLE HOSE WITH SP RAY OR JET

HANDSET FITTINGS

Diagram 2

Type AG

Bidets of this type may:

a. Be supplied with cold and / or hot water

through type AA, AB, AD or AUK1

backflow prevention arrangement or

type DC device serving the bidet only. See

Diagram 3: or

Type AA, AB, AD or AUK1 air gap with or

without blended water cistern or type DC

backflow Prevention device.

b. Be supplied with cold water from an

independent distributing pipe serving

the bidet only, or a common

distributing pipe serving the bidet and

which may also serve a WC or urinal

flushing cistern at a lower level. See

Diagram 4; or

Diagram 3

c. Be supplied with hot water from a water heater, which is supplied from an

independent distributing pipe, that serves the bidet only. See Diagram 4: or

Diverter or

separate control

valves to hose or

ascending spray

Type AA, AB, AD or AUK1 air gap with

or without blended water cistern or

Type DC backflow prevention device

Zone of backflow risk

300mm minimum

Hot and

cold water

supply or

distributing

pipes to

mixer

Blended cold

and hot water

distributing

pipe

d. Where the bidet is at a lower elevation

than any other outlets or appliances, be

supplied with water from a common

cold and / or hot water vented

distribution pipe providing that;

(i) the elevation of the spillover level of

the bidet, if there is no flexible hose;

(ii)the elevation of the spray outlet, with

the hose extended vertically above

the spill over level of the bidet

Whichever is the highest, is not less than

300mm below the point of connection with

the distributing pipe which serves over

appliances or outlets. See Diagram 5.

SgV WP

Storage cistern with

Type AGair gap

Hot water

heater serving

single bidet only

(see G15.10c)

DP to serve WC

or urinal flushing

cistern only (see

G15.10b)

Cold water DP to

other appliances

Bidet

Diagram 4

The method of supplying water to

an ascending spray and / or hose

and spray bidet is illustrated in

Diagram 3 and which is described

in the formal guidance, is difficult

to achieve in practice. The air gap

should be located above the fully

extended hose and spray, or zone

of backflow risk, and this height

may need to be increased to

provide sufficient water pressure,

to overcome friction loss in the

pipes and fittings, in order to

operate the ascending spray and

hose spray effectively. This method

of supplying blended water to a

bidet involves complicated control

methods as the control of water

to the bidet itself has to be linked

with the control

DDDDiiiiaaaaggggrrrraaaammmm 5555

SgV SgV SgV

The bidet must be located

below the spillover lever of the

lowest sanitary fitting and

below any hot water storage

vessel or ancillary pipework

Not less

than

300mm

Bidet with

ascending

spray only

Not less

than

300mm

Mixing

valve

Bath

Washbasin

Diagram 5

Cold water

storage

cistern

of water flow, and temperature, upstream of the air

gap, blended water cistern or DC device.

Installation -Basin / Bath taps

1. Identify all components are present prior to

starting installation.

2. Install the taps to the basin / bath, ensuring the plinth

is fitted between the tap body and the basin / bath.

Slide

the washer (6) onto the threaded tail of the tap and

screw the backnut (7) onto the tail until tight to

secure the taps in place.

Note: Supplied with plastic backnuts which

must be tightened fully using a suitable

spanner.

3. Connect the hot and cold water supplies to

the threaded tails.

4. Turn on the water supplies.Operate both taps,

letting the water flow for afew minutes to check all

joints and connections for any leaks.

Installation –Small Basin Mixer

1. Identify all components are present prior

to starting installation.

2. Install the mixer body (7) to the basin,

ensuring plinth (8) and washer (9) and

fitted between the mixer body (7) and

the basin.

3. Screw the threaded rods (12) and flexible

connecting pipes (14) into the bottom of

the mixer body (7).

4. Slide the ‘C’ shape rubber washer (10)

and ‘C’ shaped metal washer (11) onto the

threaded rods (12) up to the underside of

the basin.

5. Secure the mixer body (7) to the basin

by tightening the fixing nuts (15) onto

the threaded rods (12) until they are fully

tightened against the ‘C’ shaped metal

washer (11).

6. Turn on both water supplies and operate

the lever handle (3) up and side to side,

letting the water flow for a few minuets

to check all joints and connections for

any leaks.

Installation -Eco Basin Mixer & Eco Basin Mixer (No Waste)

1. Identify all components are present prior to starting installation.

2. Fit the mixer body to the basin/bidet using the 'C' plate fixing kit. The full

rubber washer (8) goes between the fitting and the basin and the 'C' shaped

rubber (9) and metal washers (10) on the underside of the basin to be secured

by the nuts (12) and threaded rods (11).

3. Fit the flexible tail pipes (13) by (HAND

ONLY) (DO NOT OVERTIGHTEN) inside

of the fitting and connect the hot and cold

supplies using washers (14) and suitable

fittings. (Not Supplied).

(See ADDITIONAL

SAFETY FEATURE)

4. Fit the pop up waste (if applicable) washer

(16) above and washer (18) below the

basin/bidet.

It is recommended that a silicone sealant be

applied to both sealing faces of washers 16

and 18. The plug height can be set by,

adjusting the waste rod (6) and operating

rod (19) connecting bracket(15), and the

screw in the base of the plug. Friction for

the waste mechanism can be adjusted using

the waste cap (20) (DO NOT OVER-

TIGHTEN).

5. Fully open the mixer in the mid position,

letting it run for a few minutes and check

all joints and connections for leaks.

Installation –Tall Basin Mixer

1. Identify all components are present prior to

starting installation.

2. Install the mixer body (7) to the basin, ensuring

the plinth (8) and washer (9) are fitted between

the mixer body (7) and the basin.

3. Screw the threaded rods (12) into the bottom of the

mixer body (7).

Note: The copper connecting pipes are pre-installed into the

mixer body (7). DO NOT attempt to remove them as this

could cause a leak from the connection.

4. Slide the ‘C’ shaped rubber washer (10) and ‘C’ shaped

metal washer (11) onto the threaded rods (12) up to the

underside of the basin.

5. Secure the mixer body (7) by tightening

the fixing nuts (13) onto the threaded

rods (12) until they are fully tightened

against the ‘C’ shaped metal washer (11).

6. Turn on both water sup[plies

and operate the lever handle

(3) up and side to side,

letting the water flow for a

few minutes to check all

joints and connections for

and leaks.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bristan Küchen- und Badezimmerausstattung Handbücher

Bristan

Bristan Bright BRG BAS C Bedienungsanleitung

Bristan

Bristan MINI2 TS1203 CL C Montageanleitung

Bristan

Bristan Liquorice LQR PROSNK C Verdrahtungsschema

Bristan

Bristan FH TDRD01 C Bedienungsanleitung

Bristan

Bristan Claret CLR BASNW C/WHT Montageanleitung

Bristan

Bristan 1901 Bedienungsanleitung

Bristan

Bristan Oval Tap Series Verdrahtungsschema

Bristan

Bristan Z2 1/2 C Verdrahtungsschema

Bristan

Bristan Z2 BIB C Verdrahtungsschema

Bristan

Bristan W SNK5C Verdrahtungsschema

Bristan

Bristan Prism Bedienungsanleitung

Bristan

Bristan GWF BF C Verdrahtungsschema

Bristan

Bristan Prism PM 3HWMBAS C Bedienungsanleitung

Bristan

Bristan Nero NR BASNW C Verdrahtungsschema

Bristan

Bristan Kingsbury Verdrahtungsschema

Bristan

Bristan VT 1/2 C Bedienungsanleitung

Bristan

Bristan Oval Series Bedienungsanleitung

Bristan

Bristan AR THBSM C Bedienungsanleitung

Bristan

Bristan CAS BAS C Bedienungsanleitung

Bristan

Bristan Nero Series Bedienungsanleitung

Bristan

Bristan Capri Bedienungsanleitung

Bristan

Bristan Artisan Evo Montageanleitung

Bristan

Bristan AR SNKPURE C Bedienungsanleitung

Bristan

Bristan Club DUC HNK C Bedienungsanleitung

Beliebte Küchen- und Badezimmerausstattung Handbücher anderer Marken

Grohe

Grohe BRIDGEFORD 33 870 Bedienungsanleitung

Hans Grohe

Hans Grohe Zenio Metro 31811000 Bedienungsanleitung

Gröne

Gröne Zedra 32 555 Bedienungsanleitung

Transform

Transform QL045 Bedienungsanleitung

Sanela

Sanela SLU 09PTB Bedienungsanleitung

Glacier bay

Glacier bay FP4A0052BNV Montageanleitung

Lefroy Brooks

Lefroy Brooks C1-1400 Montageanleitung

Grohe

Grohe Rapido E Bedienungsanleitung

Danze

Danze D302455 Bedienungsanleitung

Waterworks

Waterworks CEKM30 Merkblatt

Helvex

Helvex Omega TV-298 Bedienungsanleitung

Tribata.

Tribata. GEORGIAN G5393 Bedienungsanleitung

Alpha Bidet

Alpha Bidet Alpha One Bedienungsanleitung

InSinkErator

InSinkErator H/HC3300 Installationshandbuch

Clou

Clou Xo type 1 Bedienungsanleitung

Kohler

Kohler Contra 26448T-4 Bedienungsanleitung

Grohe

Grohe Bridgeford 20 158 Bedienungsanleitung

Hans Grohe

Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Bedienungsanleitung