Bristan EXD BAS C Bedienungsanleitung

Please keep this booklet for future

reference.

Installer, when you have read these

instructions please ensure you leave them

with the user.

Installation Instructions

Exodus Tap Range

Models covered:

EXD BAS C, EXD 1HBF C, EXD 2HBSM C,

EXD TBAS C

Contents

Thank you for choosing Bristan, the UK’s leading taps and showers expert.

We have designed this product with your enjoyment in mind. To ensure that it works

to its full potential, it needs to be ﬁtted correctly. These ﬁtting instructions have been

created to give you all of the information you need and, if you need any further help,

please do not hesitate to contact us.

Important Safety Information................................................... 3

General Information ................................................................. 4

Speciﬁcations ........................................................................... 5

Dimensions............................................................................... 6-7

Installation Requirements ....................................................... 8

Installation................................................................................ 9-10

Basin Mixer / 1 Hole Bath Filler / Tall Basin Mixer................. 9

Bath Shower Mixer................................................................... 10

Maintenance ............................................................................. 11

Troubleshooting........................................................................ 12

Notes......................................................................................... 13

Guarantee ................................................................................. 14-15

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Important Safety Information

•Please read these instructions thoroughly and retain for future use.

•All products manufactured and supplied by Bristan are safe provided they are

installed, used correctly and receive regular maintenance in accordance with these

instructions.

•If you are in any doubt about your ability to install this product safely you must

employ the services of an experienced qualiﬁed plumber.

•This ﬁtting needs to be installed in accordance with, and meet the requirements of the

Water Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.

•Remove all packaging and check the ﬁtting for damage before starting installation.

•Warning: Before starting any installation please consider the following: before

drilling into walls, check that there are no hidden electrical wires, cables or water

supply pipes. This can be checked with the aid of an electronic detector.

•If power tools are used do not forget to: - Wear eye protection

- Unplug equipment after use

•Important: Remember to turn off the mains water supply before connecting to any

existing pipe work. Fitting isolating valves to the inlet feeds is recommended for ease

of maintenance.

•Warning: Before installing the new ﬁtting it is essential that you thoroughly ﬂush

through the pipework in order to remove any remaining swarf, solder, etc.

Failure to carry out this procedure could cause problems or damage to the workings of

the ﬁtting.

•Take care when handling the ‘ﬂexible connecting pipes’, do not bend, twist or crush

them. Only tighten the pipes by hand.

•Do not crush or kink the shower hose, this could damage the hose and cause leaks.

• This product must not be modiﬁed in any way as this will invalidate the guarantee.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

General Information

This product has been tested to the Water Regulations Advisory Scheme (WRAS) and

satisﬁes the requirements of the Water Supply (Water Fittings) Regulations 1999 and

current bylaws. For full Installation Requirements & Notes (IRN) please visit

www.wras.co.uk/directory.

Designed to comply with BS EN 200 for combination taps to be used within systems

designed to BS 6700.

BS 6700 recommends the temperature of stored water should never exceed 65°C.

A stored water temperature of 60°C is considered sufﬁcient to meet all normal

requirements and will minimise the build up of lime scale in hard water areas.

If the ﬁtting is installed at low pressure (tank fed), then the minimum distance from the

highest installed position of the outlet to the underside of the cold tank should be at

least 10 metres to ensure adequate performance.

These taps and mixers should be installed in compliance with the Water Regulations.

Where the supplies are unbalanced, i.e. Hot water from cylinder tank / cold from the

mains, approved check valves must be ﬁtted in the supply pipes.

For further details contact your Local Water Authority.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Speciﬁcations

Product Code Working pressure Inlet

Min Max

EXD BAS C 1.0 5.0 M10 15mm Compression Flexible Tails

EXD 1HBF C 1.0 5.0 M12 15mm Compression Flexible Tails

EXD 2HBSM C 1.0 5.0 M12 15mm Compression Flexible Tails

EXD TBAS C 1.0 5.0 M10 15mm Compression Flexible Tails

Maximum static pressure- 10.0 bar

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Dimensions

Dimensions are nominal and in millimetres.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Basin Mixer

Tall Basin Mixer

Basin Mixer

115

125

110

112

214

120

Dimensions Cont.

Bath Shower Mixer

Dimensions are nominal and in millimetres.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

1 Hole Bath Filler

130

233

150

170

105

150

145

130

Installation Requirements

Flexible Connecting Pipes

Care must be taken when connecting the

ﬂexible connection pipes to the household

pipework to ensure they do not bend sharply

and kink or twist.

See below for recommended ways to ﬁt the

ﬂexible connecting pipes.

Slight

bend

90°

Angle

Kink Curved

round

Twists

Important: Failure to follow these guidelines may result in poor performance and damage

to the ﬂexible connecting pipes.

Important: Full access must be made available on installation for future maintenance/

servicing purposes.

System Requirements:

Gravity fed hot & cold (Equal pressures)

Gravity fed hot & cold (Differential pressure, maximum ratio 5:1)

Unvented systems

Instantaneous water heater (Combination boiler)

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Installation

1. Screw the ﬂexi tails into the bottom of

the tap body and tighten by hand only

(DO NOT OVERTIGHTEN).

2. Feed the ﬂexi tails through the hole,

in the basin / bath, ensuring the washer

is ﬁtted between the body and the basin/

bath.

3. Screw the ﬁxing rods into the bottom

of the tap body. Slide 'C' shaped rubber

washer and 'C' shaped metal washer onto

the ﬁxing rods up to the underside of the

basin.

4. To secure the tap in place tighten the

ﬁxing nuts onto the ﬁxing rods until they

are fully tightened against the 'C' shaped

metal washer, the ﬁxing nuts can be

tightened with a suitable spanner.

5. Connect the ﬂexi tails to the hot and

cold water supplies.

6. Fit the clicker waste ensuring the

rubber washer is ﬁtted between the basin

and the waste. Place the other rubber

washer under the basin and secure in

place by tightening the backnut. In order

to ﬁll the basin, the button in the middle of

the waste needs to be pressed down. To

release the water, press the button again.

7. Turn on both water supplies, operate

the handle in both directions, letting the

water ﬂow for a few mninutes to ﬂush

through the system.

8.Check all joins and connections for any

leaks.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Basin Mixer / 1 Hole Bath Filler/

Tall Basin Mixer

Installation Cont.

Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Bath Shower Mixer

1. Remove the metal and rubber washers

from body/ handset holder threaded tails.

2. Fit the body to the bath ensuring that

the washer is ﬁtted between the body and

the bath.

3. Secure the body to the bath using the

washer and metal backnut below the bath.

Tighten the backnut onto the threaded

tail. A suitable spanner may be required to

fully tighten the backnut.

4. Screw the ﬂexi tails into the bottom of

mixer body and tighten by hand only

(DO NOT OVERTIGHTEN)

5. Connect the ﬂexi tails to the hot and

cold water supplies.

6. Fit the handset holder base ensuring

the washer is ﬁtted between the base and

the bath.

7. Secure the handset holder base to the

bath using the washer and metal backnut

below the bath. Tighten the backnut onto

the threaded tail.

A suitable spanner may be required to

fully tighten the backnut.

8. Feed the hose through the handset

holder base and connect the hose to the

shower outlet pipe using the small sealing

washer.

9. Fit the handset to the hose using the

small washer.

10. Turn on both water supplies, operate

handle in both directions, letting the water

ﬂow for a few minutes to ﬂush through

the system.

11. Check all joints and connections for

leaks.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan PM2 SHCDIV C Verdrahtungsschema

Bristan

Bristan Artisan Verdrahtungsschema

Bristan

Bristan Star FH STRD01 C Bedienungsanleitung

Bristan

Bristan VAC BAS C MT (D4) Verdrahtungsschema

Bristan

Bristan SK1850- SK1850-2 Original Betriebsanleitung

Bristan

Bristan Jute JU BSM C Bedienungsanleitung

Bristan

Bristan OR2 SHXSM C Montageanleitung

Bristan

Bristan Java J BASNW C Bedienungsanleitung

Bristan

Bristan KN2 SHXAR C Montageanleitung

Bristan

Bristan W BATH05 C Verdrahtungsschema

Bristan

Bristan W SNK6 C Bedienungsanleitung

Bristan

Bristan Quest Easyfit Verdrahtungsschema

Bristan

Bristan GLE385 W Montageanleitung

Bristan

Bristan N2 SHC3STP G Verdrahtungsschema

Bristan

Bristan DUL3 THBSM C Bedienungsanleitung

Bristan

Bristan ALP Series Verdrahtungsschema

Bristan

Bristan Z TC 1/2 C Bedienungsanleitung

Bristan

Bristan Jute JU BASNW C Bedienungsanleitung

Bristan

Bristan IRBS4-CP Montageanleitung

Bristan

Bristan Joy care Montageanleitung

Bristan

Bristan SMILE SM 1/2 C D6 Verdrahtungsschema

Bristan

Bristan AR2 SHXVOFF Montageanleitung

Bristan

Bristan IRN R001 Bedienungsanleitung

Bristan

Bristan Vantage VTX 1/2 C Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung