BRONKHORST D-6300/FS Bedienungsanleitung

MASS-STREAMTM

Instruction Manual

D-6300/FS

Digital Mass Flow Meter as Flow Switch

Doc. No.: 9.17.114A Date: 27-07-2017

ATTENTION

Before installing and operating the instrument it is strongly recommended

that this instruction manual should be read carefully. Not following the

guidelines could result in personal injury and/or damage to the equipment.

MASS-STREAMTM Manual Flow Switch D-6300/FS

9.17.114A – edition: 2017-07

Page 2 of 36

SCOPE OF THIS INSTRUCTION MANUAL

This instruction manual of M+W Instruments GmbH covers the installation of the digital

Bronkhorst®Flow Switch instruments, a special product of the D-6300 Mass-StreamTM

series. Benefitting from the multi-functional display the D-6300/FS flow switches allow the

adjustment of an individual switch-point according to the mass flow of a gas or gas-mix.

Further information can be found in the Bronkhorst®manuals, which are also valid for the

Mass-StreamTM model series D-6300. The Bronkhorst®manuals for multi-bus instruments

have a modular set-up and include:

−Mass-StreamTM Instruction Manual D-6300 Digital Mass flow meters / -controllers

(document no. 9.17.104)

−Mass-StreamTM Instruction Manual D-6300 Multi-functional Display

(document no. 9.17.105)

−General instructions digital Mass Flow / Pressure instruments laboratory style /

IN-FLOW (document no. 9.17.022)

−Operation instructions digital instruments (document no. 9.17.023)

−Instruction Manual FlowPlot (Document Nr. 9.17.030)

The information in this manual has been reviewed and is believed to be wholly reliable.

No responsibility, however, is assumed for inaccuracies. The material in this manual is for

information purposes only, and is subject to change without notice.

MASS-STREAMTM Manual Flow Switch D-6300/FS

9.17.114A – edition: 2017-07

Page 3 of 36

Warranty

M+W Instruments GmbH grants a warranty on its products according to the General

Terms and Conditions. The warranty is limited to the flow switch product special of the

digital mass flow meters and its components. The correct use of the device under the

observation of all specified operation conditions is the precondition for the warranty.

ATTENTION!

The warranty is solely limited to the flow switch instruments and its components. No

warranty claims are accepted in case of a faulty operation of the instrument, like a wrong

electrical hook-up for example.

Any liability is explicitly excluded for any secondary damage, caused by the instrument’s

failure or the malfunction of any component. All wear parts, like seals for example, are

also excluded from the warranty.

The products of M+W Instruments GmbH are warranted against defects in material and

workmanship for a period of three years from the date of shipment, provided they are

used in accordance with the ordering specifications and they are not subjected to abuse

or physical damage by fall, heat or other external influences.

Products that do not operate properly during this period may be repaired or replaced at no

charge. Repairs are normally warranted for one year or the balance of the original

warranty, whichever is the longer.

See also paragraph A-V and B-II of the Terms and Conditions of sales of the

M+W Instruments GmbH.

MASS-STREAMTM Manual Flow Switch D-6300/FS

9.17.114A – edition: 2017-07

Page 4 of 36

The warranty includes all initial and latent defects, random failures, and indeterminable

internal causes. It excludes failures and damage caused by the customer, such as

contamination, improper electrical hook-up, physical shock etc.

Re-conditioning of products primarily returned for warranty service that is partly or wholly

judged non-warranty may be charged for.

M+W Instruments GmbH prepays outgoing freight charges when any party of the service

is performed under warranty, unless otherwise agreed upon beforehand. However, if the

product has been returned collect to M+W Instruments GmbH, these costs are added to

the repair invoice. Import and/or export charges, foreign shipping methods/carriers are

paid for by the customer.

MASS-STREAMTM Manual Flow Switch D-6300/FS

9.17.114A – edition: 2017-07

Page 5 of 36

Table of Contents

1 SHORT FORM START-UP………………................................................................ 6

2 FLOW SWITCH INSTRUMENTS D-6300/FS.......................................................... 7

2.1 General……............................................................................................................. 7

2.2 Installation...............................................................................................................9

2.3 Operation and Maintenance.................................................................................10

2.4 Output Variants of the Switch-Point……….…….………………………..……….. 11

2.4.1 Variant 1 „OFF – ON – OFF“……..……………………………………….… 12

2.4.2 Variant 2 „ON – OFF – ON“…..…..……………………………………….… 13

2.5 Setting of the Switch-Point using the Multi-functional Display.…...……...….. 15

2.5.1 Password Protection..………………………………………………………… 15

2.5.2 Basis Settings in the ʹAlarmʹMenu………………………………………… 17

2.5.3 Example for Switch-Point settings „Minimum-Maximum-Alarm“..…… 18

2.5.4 Adjustment of the Alarm-Reset Function „automatic ↔ manual”……. 22

2.6 Specifications of MASS-STREAMTM Flow Switch D-6300/FS………………….. 23

2.6.1 Hook-up Diagram RS232 and Analog I/O, 8-pole round (male)..…….... 24

2.6.2 8DIN Connector, 8-pole round (female)…............................................... 25

3 MEASUREMENT PRINCIPLE AND CALIBRATION.............................................26

3.1 CTA Through-Flow Measurement....................................................................... 26

3.2 Functional Block Diagram………........................................................................ 27

3.3 Calibration and Look-up Table............................................................................ 28

4 OPERATION VIA RS232....................................................................................... 29

4.1 Input Signal via FlowView....................................................................................31

5 MANUAL INTERFACE: Micro Switches and LED’s……………………………… 34

The dimensional drawings and hook-up diagrams of the MASS-STREAMTM Digital

Instruments D-6300 are available for download on our website

www.bronkhorst.com.

MASS-STREAMTM Manual Flow Switch D-6300/FS

9.17.114A – edition: 2017-07

Page 6 of 36

1 SHORT FORM START-UP

All necessary settings for this instrument are already performed at M+W Instruments

GmbH. Following the next steps carefully is the quickest way to get the instruments

operational in your own system:

Connection

Make sure your PC or PLC is connected to the RS232 interface by means of the correct

cable.

The maximum cable length for communication via RS232 must not exceed 10 m!

Power Supply

Make sure that the instrument or interface is connected to the power supply:

+15 Vdc up to +24 Vdc (please check on instrument label)

COM-Port Settings

Use settings [38400,n,8,1] for your COM-Port:

Baud rate = 38400 Baud, no parity, 8 data bits, 1 stop bit.

In case of any trouble during installation or to set up the communication Bronkhorst®

programs like FlowDDE or HyperTerminal (available in MS-Windows) could be very

useful. Please refer to chapter 4 how to use FlowDDE.

MASS-STREAMTM Manual Flow Switch D-6300/FS

9.17.114A – edition: 2017-07

Page 7 of 36

2 FLOW SWITCH INSTRUMENTS D-6300/FS

2.1 General

The digital D-6300/FS Flow Switch instruments of M+W Instruments GmbH are thermal

measurement devices for mass flow, where the alarm function of the multi-functional

display is used for the adjustment of an individual switch-point depending on the mass

flow of a gas or gas-mix.

ATTENTION!

Flow Switches can be operated in 2 different switching variants and each variant has 3

different setting options. Upon the Flow Switch dispatch the variant for the output of the

switch-point is defined! The evaluation of the switching signal must have a minimum input

resistance of 10 kΩ.

The Flow Switches are equipped with a digital electronic multi-bus pc-board and consist

of a micro-controller with peripheral circuitry for measuring and communication. The flow

signal is measured directly in the gas flow, digitized and processed by means of the

internal software (firmware). The measured and processed values can be output through

the analog interface or through the digital RS232 communication line.

The Flow Switch instruments can be operated by means of the following options:

1. Analog interface (0…5 Vdc / 0...10 Vdc / 4…20 mA / 0...20 mA)

2. RS232 interface (connected to COM-Port by means of special cable at 38400 Baud)

The micro switches and LED’s on top of the individual instrument can also be used for

manual operations of some options (see chapter 5):

−The green LED indicates in which mode the instrument is active.

−The red LED indicates address, baud rate etc. and error/warning in relevant situations.

MASS-STREAMTM Manual Flow Switch D-6300/FS

9.17.114A – edition: 2017-07

Page 8 of 36

Scope of Delivery

Immediately upon receipt of the incoming goods the package needs to be checked for any

possible damages and the goods have to comply with the scope of delivery listed on the

packing note. In case of any damages the supplier and the freight forwarder have to be

contacted without delay.

In the event of any discrepancies please get in touch with your local distributor (see

www.bronkhorst.com) or contact us directly:

M+W Instruments GmbH

Dorfstrasse 1

D-85391 Leonhardsbuch / Germany

Tel.: +49 8166 9921 0

Fax: +49 8166 9921 22

Email: sales@mw-instruments.com

When the instrument needs to be returned please include a description of the damage in

a closed envelope.

ATTENTION!

All instruments for return must have a fully filled-in ʹDeclaration of Decontaminationʹ.

This declaration has to be attached to the shipping documents, allowing free access on

the outside of the package.

The declaration of decontamination is available on our accompanying CD with each

instrument shipment or it can be downloaded from our website www.bronkhorst.com.

Please mention the instrument’s model code and the serial number on your order, as well

as your VAT number when needed.

MASS-STREAMTM Manual Flow Switch D-6300/FS

9.17.114A – edition: 2017-07

Page 9 of 36

2.2 Installation

To avoid personal injury and/or damage to the equipment only trained and qualified

personnel shall perform the installation of the instruments:

−Read the instrument’s name plate before installation and check the electrical

connection, flow range, media to be measured, operating pressure as well as the

output signal.

−The instruments contain electronic components which are sensitive to electrostatic

discharges (ESD). Contact with electronically charged persons or objects could

possibly endanger these components or even result in their failure.

−While installing the instrument take care of the arrow marking on the instrument’s flow

body, determining the flow direction.

−Ensure that all piping is absolutely clean and without any damage. It is recommended

to install an inlet filter in front of the instrument.

−Avoid piping with small diameter at high flow rates. When possible no abrupt angles or

other disturbances shall be mounted directly in front of the instrument.

−All devices have Withworth pipe threads – type RP – according to ISO228-1

(cylindrical G-threads in inches according to BSPP). The mounting of NPT-fittings will

destroy the inlet threads in the instrument’s body.

−Using an inlet pipe with sufficient piping diameter is recommended. The length of the

inlet pipe should be at least 10 times the piping diameter.

−Before the first start-up the system has to be checked that there is absolutely no

leakage. If toxic, explosive and/or corrosive gases are to be used, ensure to purge the

system long enough with a dry, inert gas. This is also required to remove these kinds

of gases from the system.

−The instruments’ preferred mounting position is horizontally. Especially when installing

bigger mass flow meters for high flow rates (D-6380/FS and bigger) in another

mounting position you should get in contact with your distributor or with M+W

Instruments GmbH beforehand.

MASS-STREAMTM Manual Flow Switch D-6300/FS

9.17.114A – edition: 2017-07

Page 10 of 36

ATTENTION!

In the event of power loss or when unplugging the main connector the instrument will be

reset into factory settings (= delivery condition).

All instruments described in this manual carry the CE-mark. Therefore they have to

comply with the EMC requirements valid for these instruments. However compliance with

the EMC requirements is not possible without the use of proper cables and

connector/gland assemblies.

In case the instrument is connected to other devices (e.g. power supply) it has to be

ensured that the operating voltage complies with the supply voltage given on the name

plate and that the function of the shielding is not affected. M+W Instruments GmbH

recommends using standard cables following the CE-requirements and could supply them

when needed.

2.3 Operation and Maintenance

When the power is switched on a warm-up period of at least 30 sec is required allowing

the instrument’s thermal stabilisation. Afterwards the instrument will work with an

accuracy of approximately 4% FS. It takes around 30 minutes until the optimal stability is

reached and the instrument will work with an accuracy of < 2% FS. This is supposed to be

performed with or without gas flow. To avoid creating gradients it is recommended that

gas and ambient temperature are kept at the same level (max ΔT approx. ± 2…3 °C).

Otherwise the accuracy of this thermal measurement could be affected in an

unpredictable manner.

Be sure that the specified pressure ratings have been applied. Pressure surges, as may

occur during the system pressurisation, must be avoided. When starting up, always bring

the instrument gradually up to the level of operating conditions.

Inhaltsverzeichnis

Andere BRONKHORST Messgerät Handbücher

BRONKHORST

BRONKHORST mini CORI-FLOW ML120 Bedienungsanleitung

BRONKHORST

BRONKHORST Mini CORI-FLOW MI Series Bedienungsanleitung

BRONKHORST

BRONKHORST mini CORI-FLOW M12 Bedienungsanleitung

BRONKHORST

BRONKHORST FLOW-CONTROL Series Bedienungsanleitung

BRONKHORST

BRONKHORST ES-FLOW ES Series Bedienungsanleitung

BRONKHORST

BRONKHORST ES-FLOW Bedienungsanleitung

BRONKHORST

BRONKHORST BRIGHT Bedienungsanleitung

BRONKHORST

BRONKHORST EL-FLOW Prestige Bedienungsanleitung

BRONKHORST

BRONKHORST FLOW-BUS Bedienungsanleitung

BRONKHORST

BRONKHORST Mini CORI-FLOW MI Series Bedienungsanleitung

BRONKHORST

BRONKHORST mini CORI-FLOW Bedienungsanleitung

BRONKHORST

BRONKHORST mini CORI-FLOW ML120 Bedienungsanleitung

BRONKHORST

BRONKHORST CEM Bedienungsanleitung

BRONKHORST

BRONKHORST MASS-VIEW series Bedienungsanleitung

BRONKHORST

BRONKHORST MASS-STREAM D-6400 Bedienungsanleitung

BRONKHORST

BRONKHORST MASS-STREAM D-6400 Bedienungsanleitung

BRONKHORST

BRONKHORST mini CORI-FLOW M1 Series Bedienungsanleitung

BRONKHORST

BRONKHORST MASS-STREAM D-6400 Bedienungsanleitung

BRONKHORST

BRONKHORST EL-FLOW Select Series Bedienungsanleitung

BRONKHORST

BRONKHORST EL-FLOW Select Series Bedienungsanleitung

BRONKHORST

BRONKHORST LIQUI-FLOW L30 Bedienungsanleitung

BRONKHORST

BRONKHORST IQ+Flow series Bedienungsanleitung

BRONKHORST

BRONKHORST MASS-STREAMT D-6300 Bedienungsanleitung

BRONKHORST

BRONKHORST ES-FLOW 1 C Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung