BSRF AFB-250 Bedienungsanleitung

Table des matières

Read first:.......................................................................................................................................................2

Firmware revision:.........................................................................................................................................3

Description:....................................................................................................................................................4

Basics about radio over fiber:.........................................................................................................................5

Question answer about RoF.................................................................................................................................6

AFB-250:.......................................................................................................................................................8

AFR-200:.....................................................................................................................................................10

ACH-642:....................................................................................................................................................12

ACH-862:....................................................................................................................................................14

How to:........................................................................................................................................................16

Usefull datas:...............................................................................................................................................18

Insertion loss of usual coaxial cables:......................................................................................................18

Insertion loss of connectors:....................................................................................................................18

Insertion loss of 1:N port passive splitters (min theoric):.........................................................................18

Accessories:.................................................................................................................................................19

Specifications:..............................................................................................................................................20

Warranty:.....................................................................................................................................................21

Read first:

–First of all read this manual.

–RF power can be dangerous please always use or wear proper Personnal Protective

Equipment (PPI).

–Be sure to understand radiofrequency behavior when measuring power otherwise it

can destroy amplifiers or hurts.

–To use those equipments be sure to understand RF concepts such spectrum, power,

noise, intermodulation, filtering...

–Clean the device with a slightly damp cloth.

–This device must'nt be exposed to rain, moisture.

–Do not install the device near any heat sources.

–This device must be serviced by a qualified service personnel.

–Specifications are subject to change without notice.

–BSRF is not responsible of any injuries, destruction resulting of improper usage of

equipments.

0220-01-EN 2/25 www.bs-rf.com

Firmware revision:

-no firmware revision for current equipments.

If you need to make an update of firmware please contact us at:

[email protected]m

0220-01-EN 3/25 www.bs-rf.com

Description:

First of all thanks for buying this product from BSRF, we hope it will serve you well!

The BSRF radio over fiber products are used to take advantages of propagation on optical

fiber. Those devices are used to convert RF electrical signal to optical signal and convert them

back to electrical. This full analog transformation is not compatible with IP network.

0220-01-EN 4/25 www.bs-rf.com

Question answer about RoF.

1. Does it work like network devices ? NO, it's an analog modulation, you've to pay

attention on optical loss. As a rule of thumb every time you loose 1dB on the optical path

you'll loose 2dB on RF path.

2. How far can I remote antenna ? If you use just one fiber between equipments, you can

put the remote 10km from the base (5dB of optical loss leads to 10dB of RF loss). If you

add more connections between equipments or if connectors are dirty this distance will be

reduced.

3. How can I get the best from RoF for wireless microphones applications ? Well as usually

the way you place antenna is still important, the idea is to avoid too strong signals and

too weak signals !! As converter is active device it can be overloaded this lead to

intermodulation and rising noise. With a well defined antenna position, clean fiber,

sometimes filter on big rig, you will get the best RF coverage.

4. How can I get the best from RoF for IEM application ? Well as usually the way you

place antenna is still important. It's never a good idea to put the TX antenna near or in

front of a RX antenna. As AFB-350 and AFB-450 have a broadband amplifier onboard,

you should consider using an external filter to reduce noise generated by amplifier. If you

feel not comfortable with that we are here to help (really!).

5. How to handle wireless microphone multi-zone coverage with RoF ? The best idea is to

alternate A and B diversity antenna. Because diversity receivers switch from A to B

selecting the best signal. You should avoid the case where two A (or B) antennas are near

of each others because you can have drops depending on frequency and position of

emitter... If you have to put A antennas (or B) near each others consider using directive

0220-01-EN 6/25 www.bs-rf.com

antenna to « select » area of coverage.

6. Can I consider not inspecting fiber before an installation ? It's the same when you wear

glasses, generally it's quite hard to clean them when you drive... Seriously it must be

done before an installation with proper tools.

7. How can I inspect fiber ? The best way is to use a video inspection tool (ie:

VIAVI/JDSU P5000i, USB with free software, is widely used, safe for eyes). But ones

can use affordable microscope with a X200/X400 magnification (WARNING ! Don't

use it while equipment is powered as it could lead to permanent damage of your

eyes). You also need the proper microscope tip to adapt to the kind of connector

(LC/PC,LC/APC,SC/PC,SC/APC...). Of course we can help you on that topic.

AFB-250:

WARNING!: DON'T TRY TO INSPECT FIBER WITH YOUR EYES WHEN THE UNIT IS

SWITCHED ON, USE PROPER PERSONNAL PROTECTION EQUIPEMENTS.

The AFB-250 allows to remote two RX antennas over two momode fibers. Specially

made electro-optical components are used in this equipment.

This device must be used with a AFR-200 or ACH642 or ACH-862 base. Its rugged

aluminium made enclosure and its connectors are designed for on field operation. A DC-feed

12V supply, protected from short circuits, can be activated on each inputs individualy. An « RF

peak » indicator shows if the RF input level is too strong. At last a 10dB RF attenuator on each

input can be activated in order to reduce sensitivity and intermodulation. This attenuator must

be enabled on startup.

LEDS:

–Power: Green color lights up when the device is on.

–DC feed: Orange color indicates that supply is enabled for active antennas. This

orange LED will blink in case of short circuit in cable or connector.

–Optical: Green color indicates that optical converter is active.

–RF peak: This red LED lights up when RF level is too high. This may come from a

wrong antenna booster setting or a transmitter too close from the antenna.

SWITCHES:

–DC-feed : Activate 12V/200mA power supply for active antennas. Press on antenna

symbol o toggle DC feed state.

POWER:

–9-36Vdc-15W linear power supply or battery Consumption 500mA - 600mA with 1

active antenna - 750mA with 2 active antennas XLR4 Wiring : 1 - / 4 +

FIBER OPTICS:

–Neutrik OpticalCon Duo APC or LC/APC fiber optics cables linked to fiber receiver

AFR / ACF / ACH

–Each channel use a single fiber, when using a connection with LC connector, the

corresponding pin out is indicated on the Front panel close view.

RF in:

–Connect Rx Antennas A & B Passive up to 5m with RG58 and 10m with RG213 cable

Active up to 35 m with RG58 and 70m with RG213 cable.

Activate/desactivate internal attenuator:

–While switching device ON, press SWITCH RF in A. Optical A and B leds will blink

alternatively. From this moment you'll have about 10sec to set attenuation: Pressing

DC feed switch (A or B) for having RF peak led ON & DC feed OFF(10dB

attenuator activated on corresponding channel) or RF peak OFF & DC feed OFF (no

attenuation, default).

–When 10s pass, configuration will be stored in EEPROM.

0220-01-EN 9/25 www.bs-rf.com

AFB-250 specifications:

0220-01-EN 10/25 www.bs-rf.com

Specifications:

RX section

Bande

passante 470-800MHz

Entrée RF 2xBNC 50R

Télé-alim 12V/200mA

Atténuateur

RF 0/10dB

Seuil RF peak -12dBm

Sortie optique Neutrik Opticalcon,

1310nm, monomode/APC

Consommation 500mA typ.

+1 antenne 600mA typ.

+2antennes 750mA typ.

Alimentation XLR4, 12W

Dimensions 155x180x70mm

Poids 1,3kg

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere BSRF Empfänger Handbücher

BSRF

BSRF ACH-642 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung