Burster 2311 Bedienungsanleitung
OPERATION MANUAL
Resistomat 2311
PROFINET Integration into TIA Portal
Manufacturer:
© 2023
burster
praezisionsmesstechnik gmbh & co kg
burster
präzisionsmesstechnik gmbh & co kg
All rights reserved
Talstr. 1 - 5
P.O. Box 1432
76593 Gernsbach
76587 Gernsbach
Germany
Germany
Valid from:
01.02.2023
Tel.: +49-7224-645-0
Applies to:
Resistomat 2311-VXX03
Fax.: +49-7224-645-88
Email: inf[email protected]om
www.burster.com
4426-2311PROFINETIAEN-5999-081530
2of 17
Contents
1Introduction................................................................................................................................................3
2Creating new project .................................................................................................................................4
3Installation of GSDML files.......................................................................................................................5
4Creation of network connections ............................................................................................................6
5Perform a measurement and read the measurement result .................................................................9
6Further Examples ....................................................................................................................................16
6.1 Writing of string data types...............................................................................................................16
3of 17
1 Introduction
This quick start guide describes an approach how you can configure the RESISTOMAT®2311 via TIA Portal
using the example of S7-1511 CPU. Please note that the samples here cannot be directly used in your
production line because they have beed extremely simplified to reach a better understanding. Therefore, you
may have to complete them by checking of status, error, length values etc.
Note: Please also note that you will have to use the RESISTOMAT®2311 PROFINET manual to get
futher information about input and output parameters (cyclic as well acyclic data transfer).
4of 17
2 Creating new project
1. Start the Totally Integrated Automation Protal, select Create New Project (a), assign the project a
name (b) and click Create (c):
2. Go to Devices & networks (a) on the left side select Add new device (b) and look for yor CPU (c).
Afterwards click the Add button (d).
a
b
c
c
d
a
b
5of 17
3 Installation of GSDML files
Note: Please make sure that your GSDML file is compatible to the field bus firmware in the Resistomat
2311. Also for compatibility reasons, uninstall all previous GSDML files of particular device if you
have any!
1. Go to Options→Manage general station description files (GSD) (a)
2. Navigate to your Resistomat 2311 GSDML directory (a) (you will find the GSD on
www.burster.com/en/download-area), select the GSDML file (b) and click Install (c)
a
b
c
a
6of 17
4 Creation of network connections
1. Double click Device Configuration (a) in the project tree und switch to Network view (b) :
2. Now select the Resistomat 2311 device in the catalog and drag & drop it into the working area (a):
a
b
a
7of 17
3. Please select an ethernet port on the S7 and hold the left mouse button down to connect the S7 with
Resistomat 2311 (a):
4. Change now to Network view (a) to assign a controller to the Resistomat 2311. Click on the link “Not
assigned” (b) of Resistomat 2311 and select your controller (c):
a
c
b
a
8of 17
IMPORTANT: Check if devices are also connected physically to the right ports. You find the port number
assignment in the section Port-Identification of Resistomat 2311 PROFINET manual
5. Change the device name in Device view →Properties →General →Ethernet addresses:
9of 17
5 Perform a measurement and read the measurement result
In this section, you will learn how to create a simple program to start and stop a measurement periodically
and display the measured resistance value with corresponding unit in a watch table. You will need to refer to
sections PLC inputs and PLC outputs of the RESISTOMAT®2311.
PROFINET manual to understand the meaning of inputs and outputs bytes.
1. Add the variables out_start, in_ready and in_error as shown below
Note: Please note: the addresses may be different. You have to check them in the Device view
Device overview of the Resistomat®2311:
2. Expand the tree node Program blocks in the Project tree and double click Add new block:
10 of 17
3. Select in the new window Organization block (a) →Cyclic interrupt (b). Set the cyclic time to
3.000.000 µs (c). As language set SCL (d) and click OK:
4. Type in the following source code in the code field of the new block:
IF "out_start" =TRUE THEN
"out_start" := FALSE;
IF "in_error" = FALSE THEN
"read_meas_value"();
END_IF;
ELSE
IF "in_ready" = TRUE THEN
"out_start" := TRUE;
END_IF;
END_IF;
// Is measurement start set?
// Then reset it
// No error?
// Read the measurement value
// Is 2311 ready for a new measurement?
// Start a new measurement
a
b
c
d
Inhaltsverzeichnis
Andere Burster Messgerät Handbücher
Burster
Burster DIGIFORCE 9307 Bedienungsanleitung
Burster
Burster Resistomat 2316 Bedienungsanleitung
Burster
Burster 9186-V Series Bedienungsanleitung
Burster
Burster Resistomat 2316 Bedienungsanleitung
Burster
Burster RESISTOMAT 2329 Bedienungsanleitung
Burster
Burster DIGIFORCE 9311 Bedienungsanleitung
Burster
Burster REISTOMAT 2x11 EtherNet/IP Bedienungsanleitung
Burster
Burster DIGIFORCE 9307 Bedienungsanleitung
Burster
Burster DIGIFORCE 9310 Bedienungsanleitung
Burster
Burster RESISTOMAT 2329 Bedienungsanleitung
Burster
Burster 8524 Bedienungsanleitung
Burster
Burster DIGIFORCE 9307 Bedienungsanleitung
Burster
Burster 9180 Bedienungsanleitung
Burster
Burster 8627 Bedienungsanleitung
Burster
Burster RESISTOMAT 2302-V001 Bedienungsanleitung
Burster
Burster 9163 Bedienungsanleitung
Burster
Burster 9181 Bedienungsanleitung
Burster
Burster Resistomat 2316 Bedienungsanleitung
Burster
Burster TRANS CAL 7280 Bedienungsanleitung
Burster
Burster TRANS CAL 7270 Bedienungsanleitung
