C.A. Technologies Panther 100G 1590 Bedienungsanleitung

CONVENTIONAL AIR CAP AND FLUID NOZZLE CHART

MODEL

NO.

PRESS /

SIPHON AIR CAP FLUID TIP

RANGE

FAN

CONTROL SCFM AIR CAP

RING

AVAI LABL E FL UI D

NOZZLES

NEEDLES /

marking on needle

31-1593-08 0.8mm (.022") 40-1508

31-1593-18 1.8mm (.070") 40-1515

Actual fluid nozzle and air cap combinations are determined by application

*Gun inlet pressures may vary as required by application

60-1500 12.5 21-1592

P100G

1590 Pressure 21-1590 0.8, 1.8

TEFLON COATED SPRAY GUN

PRODUCT INFORMATION

Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708

www.spraycat.com

Pantant

antant

anther 1her 1

her 1her 1

her 100G 100G 1

00G 100G 1

00G 1

590590

590

Operation and Maintenance Instructions for

P100G 1590100G 1590

100G 1590100G 1590

100G 1590

Spray Guns

Operation

1. Connect air supply hose at handle of gun.

2. Connect a pressurized fluid supply or paint siphon cup to the gun fluid inlet.

3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control

fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.

4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.

Maintenance

IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation.

Several states prohibit spraying solvent into the atmosphere and require the use of covered gun cleaner.

1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures

instructions.

2. If a gun cleaner is not being used:

Remove air cap and clean separately using clean solvent.

For pressure setups, connect a pressurized solvent supply to the fluid inlet, trigger the gun allowing solvent to flow

thru the gun until clean.

For siphon setups, first clean the siphon cup thoroughly then spray clean solvent thru the gun until clean.

NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance.

Gun head disassembly and reassembly instructions:

Have repair kit # 10-110 available before gun disassembly.

Gun head disassembly

To remove the nozzle carrier (4) and air cap adapter (6):

1. Remove the air cap (1), swirl insert (2), fluid nozzle body (3), and needle (13).

2. Remove the needle seal cartridge (27).

3. Loosen the locknut (25) and remove fluid inlet (24) using a 5/8” open-end wrench.

4. The nozzle carrier (4) and air cap adapter (6) will now slide forward from the gun body (8).

Gun head reassembly

1. Install a new o-ring (7) on the air cap adapter (6).

2. Install the thread locknut (25) onto the fluid inlet (24) as far as possible.

3. Install a new fluid inlet seal (26) into the recess area on the nozzle carrier (4) inlet port.

4. Slide the nozzle carrier (4) into air cap adapter (6) and insert into the gun body (8) as far as possible. Be sure the

nozzle carrier (4) extends into the hole at the back of the gun head. Install the needle seal (27) but do not tighten.

5. Rotate the nozzle carrier (4) until the fluid inlet port in the nozzle carrier (4) is aligned with the threaded hole in the

body. While in this position, insert the fluid inlet (24) and tighten firmly.

6. Tighten the needle seal (27) to approx. 12 ft.-lb. torque.

7. Tighten the fluid inlet (24) to approx. 25 ft.-lb. torque.

8. Tighten the locknut (25) to approx. 33 ft.-lb. torque.

ITEM NO. PART NO. DESCRIPT ION ITEM NO. PART NO. DESCRIPT ION

1 21-1592 Air Cap** 16 60-202 Fluid Control Knob

2 21-1591 Sw irl Insert 17 60-104 Air Inlet Fitting

3 See Air Cap Chart Fluid Nozzle Body** 18 60-1510 Inlet Air Control

4 60-L11C Nozzle Body Carrier 19 60-1520 Air Valve Assembly

6 60-12C Air Cap Adapter 21 60-302 Air Valve Poppet

7 60-131 O-Ring* 22 60-125 Seal*

8 60-1125 Panther Gun Body Conventional 23 61-1003 Air Valve Spring*

9 98-0109 Allen Plug 24 60-126 Fluid Inlet

10 See Air Cap Chart Fan Control Assembly** 25 60-128 Locknut

11 60-119 Seal* 26 60-124 Seal*

12 60-201 Rear Bushing 27 60-1400 Needle Seal*

13 See Air Cap Chart Fluid Needle** 28 60-2101 Trigger

14 60-206 Needle Return Spring (HD)* 29 60-1033 Trigger Pivot Set

15 60-209 Spring Seat*

**See air cap selection chart on page 1 Nozzle assy kits include item numbers 1,2 and 3 (21-1590-08 & 21-1590-18)

*Indicates part included in repair kit # 10-110

Revised 3/18/14

Dieses Handbuch passt für folgende Modelle

Andere C.A. Technologies Spritzpistole Handbücher

C.A. Technologies

C.A. Technologies CAT SLP Series Bedienungsanleitung

C.A. Technologies

C.A. Technologies Panther 100G Bedienungsanleitung

C.A. Technologies

C.A. Technologies CPR Bedienungsanleitung

C.A. Technologies

C.A. Technologies H2O-CPR-G Bedienungsanleitung

C.A. Technologies

C.A. Technologies Lynx 100CVT Bedienungsanleitung

C.A. Technologies

C.A. Technologies Lynx 100C Bedienungsanleitung

C.A. Technologies

C.A. Technologies Panther 200C Bedienungsanleitung

C.A. Technologies

C.A. Technologies AutoCAT 100C Bedienungsanleitung

C.A. Technologies

C.A. Technologies Panther 200Z Bedienungsanleitung

C.A. Technologies

C.A. Technologies Lynx 100 Series Bedienungsanleitung

C.A. Technologies

C.A. Technologies Lynx L200C Bedienungsanleitung

C.A. Technologies

C.A. Technologies Jaguar 100 Series Bedienungsanleitung

C.A. Technologies

C.A. Technologies FE-Line LCFM Fehlerbehebungshandbuch

C.A. Technologies

C.A. Technologies H2O-CPR Bedienungsanleitung

C.A. Technologies

C.A. Technologies LYNX L100CM Handbuch

C.A. Technologies

C.A. Technologies Lynx L100C Bedienungsanleitung

C.A. Technologies

C.A. Technologies Lynx 100C 1590 Bedienungsanleitung

C.A. Technologies

C.A. Technologies CPR Bedienungsanleitung

C.A. Technologies

C.A. Technologies Lynx 200C Bedienungsanleitung

C.A. Technologies

C.A. Technologies Lynx 300H Bedienungsanleitung

C.A. Technologies

C.A. Technologies Tomcat Series Bedienungsanleitung

C.A. Technologies

C.A. Technologies Lynx 100CM Bedienungsanleitung

C.A. Technologies

C.A. Technologies CPR-FE Bedienungsanleitung

C.A. Technologies

C.A. Technologies AutoCAT 300C Bedienungsanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Graco

Graco 246737 Gebrauchs- und Pflegehandbuch

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

Conrad

Conrad Hobby Airbrush K3 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

Graco

Graco EM 390 Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung