Cabletron Systems FRM Bedienungsanleitung

Frame Relay Module

for the SmartSwitch 9000

Installation

Setup

Guide

The Complete Networking Solution TM

Cabletron Systems reserves the right to make changes inspecifications and otherinformation con-

tained in this document without prior notice. The reader should in all cases consult Cabletron

Systems to determine whether any such changes have been made.

The hardware, firmware, and/or software described in this manual is subject to change without

notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,

INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING

BUT NOT LIMITED TO LOST PROFITS)ARISING OUT OF OR RELATED TO THIS

MANUAL OR THE INFORMATIONCONTAINEDIN IT, EVEN IF CABLETRONSYSTEMS

HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THEPOSSIBILITYOF

SUCH DAMAGES.

ofAmerica.

See third-party software copyrights in the Frame Relay Module

User Guide.

Statements of Compliance

FCC

The equipment provided byCabletronSystems,Inc. anddocumentedinthismanual hasbeen tested

and found to comply with the limits for a Class Adigital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the installation manual, may cause harmful interference to radio commu-

nications. Operationof this equipment in a residential area is likely to cause harmful interference,

in which casethe user will berequired to, at his/her own expense, take thenecessary measures to

eliminate the interference.

To ensure compliance with the Class A FCC limits, use only shielded cables with this equipment.

Any cableinstalled above aceiling or below a floormust beof a material and construction

approved by UL for that application.

DOC (Canada)

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital

apparatus set out in theRadio InterferenceRegulations of the Canadian Department ofCommuni-

cations.

Le presentappareilnumerique n'emet pas de bruitsradioelectriques depassantles limits applicables

aux appareils numeriques de la class A prescrites dans le Reglement sur le brouillage radioelec-

triqueedictepar leministere des Communications du Canada.

Installation & Setup Guide i

About This Manual

Terminology and Conventions

Thistypefacerepresentsgeneral text. This typeface represents keyboardinput and video

output.

This symbol points toan informational note relating to the text, table, or figure that

immediately precedes or follows it.

Thissymbol and text identifiesa cautionary note, the content of which

is more critical to heed than an informational note.

References to keyboard keys appear as "[N]", where “N” is a specific key:

Screen displays are provided to show the general appearance of actual screens. They are only

examples—they do not necessarily represent an operational system.

Related Documents

Copiesofthe Frame RelayModule User Guide

and otherCabletrondocumentscanbe ordered from

Cabletron Systems oryour local distributor of Cabletron products.

ii Frame Relay Module

Installing the Frame Relay Module

The Frame Relay Module (FRM)is shipped with acable that connects the

module’s RJ45 LAN (Ethernet or Token Ring, depending on the model) con-

nector to a LANinterface, located either on an interface module in the Smart-

Switch 9000 or external to the rack. Ifthe FRM will connect to an interface

module in the SmartSwitch 9000, install the FRM into the nearest available

slot. Otherwise, the FRM can be installed into any available slot.

Toinstall the FRM, follow these steps:

1. Remove the blank panel covering theslot.

All slots without modules must be covered when the

SmartSwitch 9000 is operational, to ensure proper

airflow and cooling.

2. Carefully remove the FRM from the shipping box. (Save thebox and

packingmaterials in the eventthe FRM must be reshipped.)

3. Attach one end of theESD wrist strap (packaged withthe SmartSwitch

9000 chassis) to your wrist. Plug the other end into the ESD Wrist Strap

Grounding receptacle in the lower right corner of the SmartSwitch 9000

Chassis shown in Figure 1.

4. Remove the FRM fromits anti-static bag. Observe all precautions to

prevent damage from Electrostatic Discharge (ESD).

5. Carefully examine the FRM, checking for damage. If any damage exists,

DO NOT install the module. Instead, contact Cabletron Systems Tech-

nical Support:

Phone: 603-332-9400

FAX: 603-337-3075

E-mail: support@ctron.com

6. Beforeinstalling the FRM intothechassis,ensurethat the bottomandtop

plastic tabs are unlocked. Slidethe card into an availableslot and ensure

that the circuit card is between the card guides, as shown in Figure 1.

Check both the upper and lowertracks. Take care that the module slides

in straight and engages the backplane connectors properly.Lock down the

top and bottom plastic tabs at the same time, applying even pressure.

Installation & Setup Guide 1

Figure 1 Installing the Frame Relay Module

Ensurethat thecircuit card is between thecard guides.

Lock down the top and bottom plastic tabs at the same

time, applying even pressure.

2 Frame Relay Module

Circuit Card

CardGuides

Plastic Tabs

Metal

Back Panel

Recptacle

for ESD

Wrist Strap

Installing the I/O Box Assemblies

Each of the three RLPs (RISC-based line processors) in the FRM has two

attached LICs (Line Interface Cards), shown in Figure 2. LIC 1 on each RLP

supports ports 0–3, and LIC 2 supports ports 4–7. Each LIC requires a 4-port

I/O box, as well asa cable fromthe RLP to the box. (Both are included with the

Frame Relay Module.)

Figure 2 Cards

The RLPs and LAN card are mounted into a bus located between

the two lower cards and the two upper cards.For this reason, RLPs

1 and 2 are upside-down from RLP 1.

The FRM is shipped with apairof mounting rails that will hold the I/O boxes.

Mountthe rails to the cabinet frame, and mount the I/O boxes to the rails,using

thehardwareincluded with theassemblies. SeeFigure3.Note thattherails will

hold eight I/O boxes, but no more than six are needed with an FRM.

Installation & Setup Guide 3

Figure 3 I/O Boxes and Cabling

Theexample in Figure 3shows howthe cabling would appear if the I/O boxes

wereassociated with, left to right, RLP0/LIC1 through RLP 2/LIC 2. Cabling

between the FRM and the I/O boxes might appear neater with a different

arrangement; however, the one shown in the figure provides the clearest iden-

tification of the I/O boxes after all cabling is installed.

4 Frame Relay Module

RLP 0

LIC 1

LIC 2

RLP 2

LIC 2

LIC 1

RLP 1

LIC 2

LIC 1

LAN Card

I/O Boxes

Interface Cables

RLP Cables

Cabling

LAN Adapter Cable

Connect oneend of the LAN cable to the RJ45 connector on the FRM LAN

card(seeFigure 2), and the other end to the LAN interface module. Be sure to

route thecable soas not to obstruct the ability of an installer to remove other

modules at some future date.

RLP Cables

1. Plug one end of each RLP cable (91-460-201) into an RLP connector on

the FRM. Connect the other end of the RLP cable into a 60 Pin I/O box

connector, as shown in Figure 3. (The ports arelabeled on the I/O boxes.)

Tighten the retaining screws.

2. Each RLP connector is labeled to identify its physical interface: RS-232,

V.35 and/or RS-422. Interface cables, listed in Table 1 connected to the I/

O box must be appropriate to the labeled interface of the RLP connector

towhich the I/O box is connected. (RS-422interfaces includeRS-449 and

X.21.)

Plug the interface cables into the I/O boxes, and tighten the retaining

screws. Secure the cables to the cabinet frame in such a way as to provide

a strain relief for the connectors at the I/O box end.

3. Plug theotherends of the cables into the appropriate devices: modems,

user devices, extender cables, etc.

Installation & Setup Guide 5

Checking for Proper Operation

This procedure requires an asynchronous terminal and keyboard

connected (locally or remotely) to the COM1 port on the FRM.

1. Switch on the async terminal (if necessary).

2. Observe the SMB and CPU LEDs (shown in the following figure) on the

Frame Relay Module. Both should be green.

Figure 4 LEDs

3. As the FRM boots (starts), aseries of messages track the loading of the

software. Thesemessages are writtento afile named BOOTRPT.TXT. If

there appears to be aproblem during boot-up,the contents ofthis file can

be displayed (as described later), to help determine the problem.

Whenthe bootprocess is complete, ascreen similarto Figure5 willbe dis-

played. (Nostatus will be shownuntilthe software is configured.)

6 Frame Relay Module

Table 1 I/O box Interface Cables

Part Number Description

91-291-021 V.35 DTE

91-290-020 V.35 DCE

91-290-001 RS-232 DTE

91-290-000 RS-232 DCE

91-290-011 RS-449 DTE

91-290-010 RS-449 DCE

SMB

COM1

CPU

Figure5 Port Status Display

4. Now someone must configure the software from the async terminal.

Records must be configured to identify thelocations and operating param-

eters of the FRM and its ports. Configuration of these records is docu-

mented inthe Frame Relay Module User Guide.

If you want to proceed to the configuration screens, press [F1] at the Port

Status Display. When prompted, type (uppercase) NETLINK, then press

[Enter]. (NETLINK is specified as the password when the softwareis

installed. This can be changed in a menu operation.) This will display the

Main Menu.

Figure 6 MainMenu

Installation & Setup Guide 7

To select a menuitem, press the letter displayed at theleft ofthe item.To

display a list of valid options at any point, press the [?] key.

If you want to display the BOOTRPT.TXT file, press [F], then [C]from the

Main Menu.

This completes the installation. If this FRM is the first one ina network that

contains otherFRMs running anolderrelease ofthe software, thenew software

can be downloaded to the other FRMs.

Updating Other Frame Relay Modules

To remotely update anotherFRM with softwarefromthe new FRM,follow this

procedure:

1. Make sureFileTransferIDs arespecified in the Node Defaults records of

both FRMs.

2. Press [C] at the On-Line Node Operations menu (or [B],[A], [C] from the

Main Menu).

3. When prompted, enter the FileTransfer ID and password of the node you

are updating.

4. Press [Y] or [N] when asked: Will the remote node be using any of IP, LLC2,

or IPX?

5. Press [Y] when asked: Areyousureyou want to doa remote software update?

The transfer process, repeated for each file, is as follows:

1. The originating nodewill send a message that includes the name and size

of the largest file to be sent. A request for theremote node's release

numberwill also be sent with the first filename. If the release numbers of

the sending and receiving nodes are incompatible, the transfer will not

occur, and an error message will be displayed. Ifthishappens, contact

your service representative.

2. The remote node will check to make sure there is enough disk space to

accept the file; ifnot, the connection will be clearedanda corresponding

message displayed. If there is enough disk space, the file will be trans-

ferred,and stored in the remote node undera temporary file nameuntil the

node verifies that the file is the expected size. (If it is not, the temporary

file will be deleted.)

3. If the temporary file is the expected size, the"old" file will be deleted and

the new file renamed.As the update progresses, you can press [F4] at any

timeto abortthe transfer andclear the connection.Oncetheupdate is com-

plete, the sending node will clearthe connection.

8 Frame Relay Module

Node Name=

Port Status Display

P Type PPS Conn# State P Type PPS Conn# State

F1: Login

Node Name=

M A I N M E N U

A Configuration

B Operations

C Status Displays

D Events

E Ststistics

F Reports

Option:

Questions?

Ifyou havequestions orproblems,pleasecontact CabletronSystems Technical

Support at:

Phone: 603-332-9400

Fax: 603-337-3075

E-mail: support@ctron.com

Installation & Setup Guide 9

Document number 09-48-06-001-01

The Complete Networking Solution TM

Andere Handbücher für FRM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cabletron Systems Schalten Handbücher

Cabletron Systems

Cabletron Systems SmartSTACK ELS10-27TX Betriebsanleitung

Cabletron Systems

Cabletron Systems FPIM 02 FPIM-02 Bedienungsanleitung

Cabletron Systems

Cabletron Systems Cabletron CyberSWITCH CSX5500 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch 9A100 Montageanleitung

Cabletron Systems

Cabletron Systems FN10 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SEH100TX-22 Bedienungsanleitung

Cabletron Systems

Cabletron Systems TRXI-22 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch 1800 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MiniMMAC Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartCell 6A000 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9H531-24 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9T125-24 Handbuch

Cabletron Systems

Cabletron Systems SmartCell 6A000 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9A000 Bedienungsanleitung

Cabletron Systems

Cabletron Systems MMAC-Plus 9F310-02 Bedienungsanleitung

Cabletron Systems

Cabletron Systems IA1100 Bedienungsanleitung

Cabletron Systems

Cabletron Systems ESX-1320 Bedienungsanleitung

Cabletron Systems

Cabletron Systems 924TX Bedienungs- und Wartungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch 2500 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch 6500 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartCell 6A000 Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSTACK 100 ELS100-24TX Montage- und Bedienungsanleitung

Cabletron Systems

Cabletron Systems CSX200 CyberSWITCH Bedienungsanleitung

Cabletron Systems

Cabletron Systems SmartSwitch 9W006 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung