CAME RIOED8WS Bedienungsanleitung
CAME S.p.A.
Via Martiri Della Libertà, 15
31030 - Dosson di Casier
Treviso - Italy
RIOED8WS
-20°C 55°C
IP54
145
57
34
CH 1
T 1
T 2
IN 1 IN 2
CH 2
A
②
③
④
①
CR123A
FA01259M4A - 10/2018
FA01259M4A
IT
Italiano
EN
English
FR
Français
RU
Pусский
FA01259M4A - 10/2018
120
35
⑤
⑦
⑩⑥
⑧
B
FA01259M4A - 10/2018
IN 1 IN 2
IN 2
IN 1 IN 2
IN 1
IN 2
IN 1
CH 1
CH 2
T1
T2
CH 1
CH 2
T1
T2
C
NCNOC
IN 1 IN 2
IN 2
IN 1 IN 2
IN 1
IN 2
IN 1
CH 1
CH 2
T1
T2
CH 1
CH 2
T1
T2
C NO NC
8,2 kΩ
DF DFWN
⑪⑫
FA01259M4A - 10/2018
FA01259M4A - 10/2018
ENGLISH
To access the installation video, use the QR code.
General Precautions
Before installing, carefully read the instruc-
tions and follow the process explained by
the manufacturer.
Installing, programming, commissioning
and maintenance of this device must be
only done by qualified, specifically trained
technicians, and in full compliance with
any applicable regulatory provisions, in-
cluding workplace safety and waste dis-
posal standards and regulations. Modifying
the project or set up of the device without
first checking with the manufacturer or au-
thorized dealer may be hazardous.
Came S.p.A. is not liable for any damage
caused if the product is used improperly,
wrongfully or unreasonably.
Before carrying out any cleaning or main-
tenance operation, disconnect the device
from the power supply.
The equipment must be destined solely
for the use for which it was expressly de-
signed.
The manufacturer can not be held liable for
any damage resulting from improper, un-
reasonable, and/or erroneous use.
Install in state-of-the-art fashion, so that
the casing remains clean and watertight.
FA01259M4A - 10/2018
⚠INCOMPATIBLE WITH RIO SYSTEM VERSION 1.0
Description
Wireless module for controlling one or two sensitive safety-
edges that communicate with the RIOCT8WS or the RIOC-
N8WS control card, complete with buzzer for warning that
the batteries are flat or that there are radio communications
issues.
Main control-card components A
① Buzzer
② CH1 and CH2 warning LED
③ Programming buttons T1 and T2.
④ Terminals for connecting the sensitive safety-edges
Main casing components B
⑤ Casing base
⑥ Casing cover
⑦ Card-fastening screw
⑧ Cover fastening screw
⑩Board
Technical data
Type RIOED8WS
Power supply (V DC) 3
Stand-by absorption (µA) 80
Current draw in transmission (mA) 15
One CR123A (mAh) lithium battery 1700
*Battery life (months) 24
Radio frequency (MHz)
868.95
Radio range over clear areas (m) 30 max.
Infrared range (m) 10
** Radio range over clear areas (m) 30 max.
Transmission power (dBm) 10 max.
Materials PC-ABS
*The battery duration is calculated on a yearly average of
20 daily-maneuvers.
** Do not place the RIOCN8WS or the RIOCT8WS card
behind walls, metal fences or any other obstructions that
could interfere with radio communications.
Installation and connections B/ C
FA01259M4A - 10/2018
⚠ Fit the RIOED8WS photocells near the RIOCN8WS or
the RIOCT8WS card, so as not to have any metal or cement
obstructions.
- Fit the base ⑤onto the chosen surface with suitable nuts
and bolts.
- Fit the control card ⑩ into the casing ⑨.
- Fasten with the supplied screw ⑦.
- Resistive, sensitive-safety edges: connect the
DFWN-series edges to the IN1 or IN2 terminals, and cut
out the resistor as shown ⑪.
- NON-resistive, sensitive-safety edges: connect the
DF-series edges to the IN2 or IN1 terminals, and add the
supplied 8.2 kΩ resistor as shown ⑫.
- Save the RIOED8WS wireless module to the RIOCT8WS or
the RIOCN8WS card (see the chapter on SAVING).
- Make the necessary functional checks (see the RIOCT8WS
or the RIOCN8WS manual).
- Shut the casing by latching the top of the cover and fasten-
ing it with the supplied screw ⑥.
Saving
Fit the batteries into all accessories that will be saved.
⚠After three minutes, the devices shift into stand-by mode;
to reactivate them, press T1 or T2 for one second.
Check that the CH1 and CH2 LEDs are flashing red simulta-
neously, otherwise do a RESET (see THE RESETTING PRO-
CEDURE).
First T1 or T2 storage
Press, for one second, the T1 or T2 button on the RIOED8WS
card: the CH1 and CH2 LEDs will flash red in alternation.
Press, for one second, the PROG button on the RIOCN8WS
card or the RIOCT8WS card: the WIRELESS LEDs, on the
RIOCN8WS or the RIOCT8WS card, will switch from flashing
to o, and the CH1 LED on the RIOED8WS card will make a
quick blue flash to confirm the programming.
To add an additional IN1 or IN2 input to an already associa-
ted device, press exclusively the button related to the new
input added (IN1 = T1 IN2 = T2).
⚠To stop the STORAGE procedure, press the RESET key
for one second at any time.
Resetting procedure
- Keep pressed the T2 button on for about 10 seconds on
the RIOED8WS card, until the CH1 and CH2 LEDs flash red.
☞If you replace any device on the system, you will have
FA01259M4A - 10/2018
to RESET and then again save all of the system devices.
Batteries
⚠Only replace with the same or equivalent battery type.
⚠Keep the batteries away from children’s reach. If swal-
lowed, seek immediate medical attention.
⚠The supplied battery’s life also depends on its storage
time. Fit the batteries when saving.
⚠When the batteries are almost flat on the RIOED8WS
device, it makes a buzzing sound every 10 seconds.
If a battery is replaced in the system, it is NOT necessary to
perform the device STORAGE procedure again.
Troubleshooting
See the chapter on: troubleshooting issues on the RIOCT-
8WS or the RIOCN8WS control card.
CAME S.p.A. declares that the RIOED8WS photocells
conform to the provisions of directive 2014/53/EU.
The complete wording of the EU declaration of con-
formity is available at the following Internet address:
www. came.com.
RIOED8WS paired with RIOCT8WS and together with an
operator, or a control panel, with safety test enabled, is a
Category 2 safety device according to EN 954-1.
RIOED8WS paired with a RIOCN8WS, is a Category 2
safety device according to EN 954-1.
Decommissioning and disposal. Dispose of the pack-
aging and the device at the end of its life cycle respon-
sibly, in compliance with the laws in force in the country
where the product is used. The recyclable components
are marked with a symbol and the material's ID marker.
The data presented in this manual may be changed, at
any time, and without notice.
Measurements, unless otherwise stated, are in millim-
eters.
Andere Handbücher für RIOED8WS
3
Inhaltsverzeichnis
Andere CAME Steuereinheit Handbücher
CAME
CAME Z Series Bedienungsanleitung
CAME
CAME ZLJ24 Bedienungsanleitung
CAME
CAME Z Series Bedienungsanleitung
CAME
CAME ZL170N Bedienungsanleitung
CAME
CAME CHOPIN KLT Bedienungsanleitung
CAME
CAME RLB Bedienungsanleitung
CAME
CAME ZL56A Bedienungsanleitung
CAME
CAME Z Series Bedienungsanleitung
CAME
CAME Z Series Bedienungsanleitung
CAME
CAME Z Series Bedienungsanleitung
CAME
CAME Z Series Bedienungsanleitung
CAME
CAME BPT DMVC/08 Bedienungsanleitung
CAME
CAME ZLJ14 Bedienungsanleitung
CAME
CAME ZBX74-78 Leitfaden
CAME
CAME RGSM001 Bedienungsanleitung
CAME
CAME 806XG-0080 Bedienungsanleitung
CAME
CAME PXONV Bedienungsanleitung
CAME
CAME Z Series Bedienungsanleitung
CAME
CAME CONNECT UR042 Bedienungsanleitung
CAME
CAME Z Series Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
