CAME FAST Series Bedienungsanleitung

F7024N

FAST SERIES

AUTOMATION FOR SWING GATES

INSTALLATION MANUAL

The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning.

ENGLISH

#

#

4.1 Operator

4 Description

2.1 Intended use

1 Legend of symbols

This symbol tells you to read the section with particular care.

This symbol tells you that the sections concern safety issues.

This symbol tells you what to say to the end-users.

2 Destination and conditions of use

The F7024N operator is designed to power residential and condominium swing gates with gate leaves weighing up

to 300 kg. Do not install or use unless as otherwise shown in this manual.

3 Reference Standards

“IMPORTANT INSTALLATION, SAFETY INSTRUCTIONS”

“CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY”

“THIS MANUAL IS ONLY FOR PROFESSIONAL OR QUALIFIED INSTALLERS”

2.2 Conditions of use

This product is engineered and manufactured by CAME CANCELLI AUTOMATICI S.p.A. and complies with current safety regu-

lations. Guaranteed 24 months if not tampered with.

External operator with articulated arm for swing gates.

Self-locking 24V D.C. gearmotor.

4.2 Technical features

Control board power supply: 230V a.c. 50/60Hz

Motor power supply: 24V d.c.

Max draw: 11A

Power: 140W

Max couple: 180Nm

Opening time (90°): fron 16 to 45s

Duty Cycle: Intensive use

Protection Rating: IP54

Weight: 28 kg

Insulation class:

The company: CAME cancelli automatici is ISO 9001:2000 quality certified; is has also obtained the ISO 14001 environmen-

tal safeguarding certification. CAME engineers and manufactures all of its products in Italy.

This product complies with the following standards: EN 12978, UNI EN 954-1, CEI EN 60335-1, UNI EN 12453.

Gate leaf width 1 m 1,5 m 2 m 2,3 m max

Gate leaf weight 300 kg max 250 kg 215 kg 200 kg

Opening 110° max

The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning.

ENGLISH

Hinge Gate stop

D= 240 mm. max

Opened to 90°

Opening

angle ABC

90°

140÷205 0÷50 430

140÷195 75÷100 430

140÷185 125÷150 400

140÷175 175÷200 400

110° 180÷210 0 430

200÷205 50 430

194 218

245

4.4 Dimensions and basic measurements

4.3 Description of parts

A1824

1) Operator

2) Pillar bracket

3) Articulated transmission arm

4) Gate bracket

The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning.

ENGLISH

N.B.: If the cable length differs from that specified in the table, then you must determine the proper cable diameter in the

basis of the actual power draw by the connected devices and depending on the standards specified in CEI EN 60204-1.

For connections that require several, sequential loads, the sizes given on the table must be re-evaluated based on actual

power draw and distances.

When connecting products that are not specified in this manual, please follow the documentation provided with said

products.

5.2 Cable list and minimum thickness

Connection Type of

cable

Length of cable

1 < 10 m

Length of cable

10 < 20 m

Length of cable

20 < 30 m

Control panel power supply 230V

FROR CEI

20-22

CEI EN

50267-2-1

3G x 1,5 mm23G x 2,5 mm23G x 4 mm2

Motor power supply 24V 3 x 1 mm23 x 1,5 mm23 x 2,5 mm2

Flashing lamp 2 x 0,5 mm22 x 1 mm22 x 1,5 mm2

Photocell transmitters 2 x 0,5 mm22 x 0.5 mm22 x 0,5 mm2

Photocell receivers 4 x 0,5 mm24 x 0,5 mm24 x 0,5 mm2

Accessories power supply 2 x 0,5 mm22 x 0,5 mm22 x 1 mm2

Control and safety devices 2 x 0,5 mm22 x 0,5 mm22 x 0,5 mm2

Antenna connection RG58 max. 10 m

5 Installation

Before installing, do the following:

• Make sure you have a suitable omnipolar cut-off device with contacts more than 3 mm apart, and independent (sectioned

off) power supply;

• Make sure you have suitable tubing and conduits for the electrical cables to pass through and be protected against mechanical

damage;

• Check that any connections inside the container (that provide continuity to the safety circuit) are fitted with additional

insulation compared to other internal live parts;

• Make sure the structure of the gate is sturdy, the hinges work and that the is no friction between moving and non-moving

parts;

• Make sure that there are mechanical endstops for both opening and closing runs.

Installation must be carried out by expert qualified personnel and in full compliance with current regulations.

5.1 Preliminary checks

The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning.

ENGLISH

Make sure you have all the tools and materials you will need for the installation at hand to work in total safety and com-

pliance with the current standards and regulations. The following figure illustrates the minimum equipment needed by the

installer.

5.4 Tools and materials

1) Automation

2) Control panel

3) Frequency card

4) Antenna

5) Flashing light

6) Selector switch

7) Photocells

8) Electric cable junction box

9) Mechanical stops

10)Transmitter

5.3 Standard installation

,/#+

5.,/#+

,/#+

5.,/#+

#!-%

The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning.

ENGLISH

5.5 Applying the base plate and A bracket

- Secure the base plate to the pillar using M8 screws and ø14 mould inserts making sure the minimum distance of 100 mm is

from the ground is met.

- Secure the A bracket (using M6 screws or by welding) to the gate leaf making sure the C 68mm distance measurements and

are met.

ø 14

Base plate

Bracket “A”

Open the lock cover (1).

Insert the key, push it down and turn it clockwise (2).

Lift the cover, loosen the Ø 3,9x13 screw and remove the cover from the gearmotor assembly (3).

(1) Ø3,9x13

(1) (2) (3)

5.6 Installing the gearmotor

* Vedi “Quote base”, pag. 3

The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning.

ENGLISH

Insert the gearmotor into the base plate’s 4 holes and secure it using the two supplied M8x90 screws and relative M8 nuts.

M8x90

(4)

- Insert and secure the straight arm into the gearmotor shaft including the pin with screw and relative spacer. Lubricate the

bushing and insert the straight arm, joining it to the curved arm using the screw, washers and nut. Release the gearmotor

and secure the curved arm to bracket ‘A’ using the screw and relative nut, making sure the arm runs freely. For the right hand

application see ﬁg. 2.

M12x40

M12

M10x14

Spacer

"Bracket A"

5.7 Applying the articulated arm

M12x55

ø 12

Bushing

ø 12

M12

The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning.

ENGLISH

Before making any adjustments to the microswitches, you must release the gearmotor by turning the apposite handle.

Handle

Opening-speed brake microswitch

Closing-speed brake microswitch

5.8 Gearmotor release

Upper cam

Lower cam

1) Release the gearmotor and manually lead the gate to its fullest opening position (max. 110°).

2) Turn the lower cam until the switch is activated.

3) Tighten the central screw.

Microswitch

Lower cam securing screw

Switch

Lower cam

5.9.1 Adjusting the opening stop

Microswitch assembly

5.9 Adjusting microswitches

The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning.

ENGLISH

IMPORTANT! The operator is ﬁtted with a standard speed brake microswitch suitable for gate leaf widths of 1.20m to 2.30 m.

CONTRARILY, IF THE GATE LEAF MEASURES LESS THAN 1.20 m, before proceeding as described above, you must…

A- Remove the 2 adjustment screws;

B- Remove, turn upside down and replace the shaped ring onto the cam (the contour sizes for activating the switch vary);

C- Retighten the securing screws.

Switch activating contour

Contoured ring

Securing screws for the upper cam

<1.20

Once the opening endstop is adjusted, then you can adjust the closing-speed brake microswitch.

Always with the gearmotor released ...

1) Manually lead the gate leaf to the fully closed position.

2) Turn the contoured cam until the micro switch is released as shown in the diagram.

3) Tighten the screws.

Microswitch

Switch

Lower cam

Securing screws for the upper cam

1.20<2.30 m

5.9.2 Adjusting the closing-speed brake

The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning.

ENGLISH

M2M1

Install the control panel and carry out the electrical connections as shown in the diagram.

Opening delayed gearmotor

Closing delayed gearmotor

5.10 Electrical connections to the control panel

ZL180

BLACK

RED

BLACK

RED

Andere Handbücher für FAST Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CAME Garagentoröffner Handbücher

CAME

CAME G4040IZ Bedienungsanleitung

CAME

CAME FAST-S24 KIT Bedienungsanleitung

CAME

CAME VER Series Bedienungsanleitung

CAME

CAME BX Series Bedienungsanleitung

CAME

CAME RIO SYSTEM Bedienungsanleitung

CAME

CAME BXV Series Bedienungsanleitung

CAME

CAME BX10 Bedienungsanleitung

CAME

CAME A 3024 N Bedienungsanleitung

CAME

CAME 8K01MB-0572 STYLO KIT Bedienungsanleitung

CAME

CAME BX Series Bedienungsanleitung

CAME

CAME v6000 Bedienungsanleitung

CAME

CAME G4140ZU Bedienungsanleitung

CAME

CAME BK-2200T Bedienungsanleitung

CAME

CAME KRONO Bedienungsanleitung

CAME

CAME 119BU50EN Bedienungsanleitung

CAME

CAME EMEGA Bedienungsanleitung

CAME

CAME 801XC-0120 Bedienungsanleitung

CAME

CAME VER-PLUS Series Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

CAME

CAME C-BX Bedienungsanleitung

CAME

CAME BX-74 Bedienungsanleitung

CAME

CAME v6000 Leitfaden

CAME

CAME RIOCT8WS Bedienungsanleitung

CAME

CAME AXI SWN20 Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Chamberlain

Chamberlain 8355 - 1/2 hp Bedienungsanleitung