CAME BX-246 Bedienungsanleitung

BX SERIES

INSTALLATION MANUAL

BX-246

AUTOMATION SYSTEMS FOR SLIDING GATES

4.1 Operator

4 Description

2.1 Intended use

1 Legend of symbols

This symbol tells you to read the section with particular care.

This symbol tells you that the sections concern safety issues.

This symbol tells you what to say to the end-users.

2 Conditions of use

The BX246 operator is designed to power sliding gates in residential and condominium settings.

Do not install or use unless as otherwise shown in this manual.

3 Reference standards

“IMPORTANT INSTALLATION, SAFETY INSTRUCTIONS”

“CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY”

“THIS MANUAL IS ONLY FOR PROFESSIONAL OR QUALIFIED INSTALLERS”

2.2 Limitations to use

This product is engineered and manufactured by CAME CANCELLI AUTOMATICI S.p.A. in compliance with current safety standards.

Guaranteed 24 months if not tampered with.

The operator is made of a cast aluminium part inside of which operates the irreversible, electromechanical gearmotor and an ABS

plastic lining which holds the electronic card, transformer and the clamp to house 2 emergency batteries.

4.2 Technical features

The company CAME cancelli automatici is ISO 9001:2000 quality certified; it has also obtained the ISO 14001 environmental safe-

guarding certification. CAME engineers and manufactures all of its products in Italy.

This product complies with the following legislation: see declaration of compliance.

For intensive or condominium use: max gate weight 600kg with max gate length 18 m.

BX246 OPERATOR

Control panel power supply: 230V A.C. 50/60Hz

Operator power supply: 24V D.C.

Draw: 10 A

Power: 400 W

Reduction ratio: 1/33

Thrust: 700 N

Max speed.: 10 m/min max.

Duty cycle: intensive use

Protection rating: IP54

Insulation class: I

Weight: 15 kg

#

#

Pag.

2- Manual code:

119BU50

119 B U 5 0 ver.

1.0

1.0 10/2007 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

4.4 Dimensions

4.3 Description of parts

(mm)

5 Installation

Installation must be carried out by expert qualified personnel and in full compliance with current regulations.

5.1 Preliminary checks

Before installing, do the following:

• Make sure that the gate is stable, and that the castors are in good working order and properly greased.

• The ground rack must be well secured to the ground, entirely above the surface and free of any irregularities that may obstruct the

gate’s movement.

• The upper guide rails must not create any friction.

• Make sure that there is a closing and an opening endstops.

• Make sure that the operator is attached to a solid surface and protected from any impacts;

• Make sure you have a suitable omnipolar cut-off device with contacts more than 3 mm apart, and independent (sectioned off) power

supply;

• Check that any connections inside the container (that provide continuity to the safety circuit) are fitted with additional insulation

compared to other internal live parts;

• Make sure you have suitable tubing and conduits for the electrical cables to pass through and be protected against mechanical

damage.

1 - Top cover

2 - Settings casing

3 - Control board support

4 - Endstop fins

5 - ZD2 electronic card

6 - Front cover to control panel

7 - Gearmotor release door

8 - Securing plate

9- Securing bolt

10- Securing screw plate

11- Nut

Pag.

3- Manual code:

119BU50

119 B U 5 0 ver.

1.0

ENGLISH

Make sure you have all the tools and materials you will need for the installation at hand to work in total safety and compliance

with the current standards and regulations. The following figure illustrates the minimum equipment needed by the installer.

N.B.: If the cable length differs from that specified in the table, then you must determine the proper cable diameter in the basis of

the actual power draw by the connected devices and depending on the standards specified in CEI EN 60204-1.

For connections that require several, sequential loads, the sizes given on the table must be re-evaluated based on actual power

draw and distances. When connecting products that are not specified in this manual, please follow the documentation provided

with said products.

5.3 Cable list and minimum thickness

Connection Type of cable Length of cable 1 < 10 m Leng. cable 10 < 20 m Leng. cable 20 < 30 m

Control panel power supply 230V

FROR CEI

20-22

CEI EN

50267-2-1

3G x 1,5 mm23G x 2,5 mm23G x 4 mm2

Flashing light 2 x 0,5 mm22 x 1 mm22 x 1,5 mm2

Photocell transmitter 2 x 0,5 mm22 x 0.5 mm22 x 0,5 mm2

Photocell receiver 4 x 0,5 mm24 x 0,5 mm24 x 0,5 mm2

Accessories power supply 2 x 0,5 mm22 x 0,5 mm22 x 1 mm2

Safety and control devices 2 x 0,5 mm22 x 0,5 mm22 x 0,5 mm2

Antenna connection RG58 max. 10 m

5.2 Tools and materials

1) BX246 Assembly

2) Rack

3) Reception Antenna

4) Flashing light

5) Keyswitch selector

6) Safety photocells

7) Electric cable junction box

8) Mechanical endstops

9) Guide rails

10) Endstop ﬁns

5.4 Standard installation





Pag.

4- Manual code:

119BU50

119 B U 5 0 ver.

1.0

ENGLISH

- Dig a pit to the side of the gate (see measurements from diagram).

Prepare the corrugated tubes you will need when making connections coming from the shunt pit.

N.B. the number of tubes depends on the type of system and the accessories you will hook up.

The following applications are only examples, as the space for installing the ratiomotor and accessories varies according to

obstructions. It is thus up to the system installer to select the most suitable solution.

Shunt pit

5.5 Securing the plate and installing the assembly

Conduits for electric

cables

-Prepare the securing plate, insert the bolts into the holes and lock them using the supplied nuts and washers. Extract the preformed

brackets using a screw driver or a set of pliers.

- Position the plate on top of the grid. Careful! The tubes need to pass through the apposite holes.

- Prepare a form box that is larger in size than the securing plate and insert it into the pit. The form box should jut 50mm above

ground level.

Insert an iron grid inside the from box to reinforce the concrete.

Pag.

5- Manual code:

119BU50

119 B U 5 0 ver.

1.0

ENGLISH

H

- To position the plate in relation to the rack please see the measurements on the diagram.

Fill the form box with cement and wait for at least 24 hours for it to solidify.

- Remove the form box, ﬁll the pit around the cement block with soil.

- Unbolt the nuts and washers from the bolts. The securing plate must be clean, perfectly aligned and with the bolt threads completely

on the surface.

Insert the electric cables into the tubes until they exit about 400mm.

Pag.

6- Manual code:

119BU50

119 B U 5 0 ver.

1.0

ENGLISH

- Remove the cover from the gearmotor by loosening the side bolts, perforate the cable shafts using a screwdriver or a pair of

scissors and position the gearmotor atop the plate. Careful! The electric cables must pass through the cable shafts.













- Lift the gearmotor from the securing plate by about 5 to 10mm by using the threaded steel-levelling feet to allow any later

adjustments between the pinion and the rack.









- The following illustrations for the securing the rack, are just examples of applications. It is up to the installer to choose the best

solution.

Releasing the gearmotor (see paragraph on manual release). Rest the rack on the gearmotor pinion.

Weld or secure the rack to the gate along its entire length.

To assemble the rack modules, use an excess piece of rack and place it under the joining point, then block it using two C-clamps.

Note: if a rack is already in place, then just adjust the pinion-to-rack distance.

Pag.

7- Manual code:

119BU50

119 B U 5 0 ver.

1.0

ENGLISH

- Open and close the gate manually and register the pinion-to-rack distance using the threaded steel-levelling feet (for vertical

adjusting) and the slotted holes (horizontal adjusting). This prevents the weight of the gate from bearing on the operator.

Once adjustments are ﬁnished, secure the assembly using the nuts and washers.

Insert the cover after performing the adjustments and settings on the electronic card.

















Levelling feet





Slotted holes

Rack

Pinion

vertical adjusting horizontal adjusting

Rack

Pinion

Pag.

8- Manual code:

119BU50

119 B U 5 0 ver.

1.0

ENGLISH









5.7 Manually releasing the gearmotor

- Insert the trilobed key into the lock, push it in and turn it clockwise ....

5.6 Mounting the endstop fins

Place the endstop ﬁns onto the rack and secure them using a 3 mm Allen wrench. Their positioning limits the gate run.

Note: the gate schould not slam against the mechanical stop, when opening or closing.

Mechanical stop

WARNING: opening the door will

disengage the motor (i.e. it will not

function).

To operate the motor the release mecha-

nism must be ﬁrmly fastened.

Trilobed key

Knob









..... open the small door and turn the release handle clockwise.

Pag.

9- Manual code:

119BU50

119 B U 5 0 ver.

1.0

ENGLISH

6 Control board

6.1 General description

FUSE TABLE ZD2

To protect: fuse:

Motor 10A-F

Control board (line) 1,6A-F

Accessories 1.6A-F

Command devices 1A-F

6.2 Main components

1) Power supply terminals

2) Endstop terminals

3) Motor terminals

4) Encoder terminals

5) Accessory fuse

6) Card fuse

7) Button for memorising the radio code

8) Radio-code signalling LED indicator

9) 230V-power signalling LED

10) Control and signalling LED group

11) Function selector DIP switch

12) Socket for connecting the remote control’s

radiofrequency card

13) Antenna terminal

14) Accessories’ and command device’s terminals

15) Motor fuse

16) Line fuse

17) Setting trimmer

18) Battery charger (LBD2) connecting terminal boards

19) Transformer-connecting terminal board

Use 230V A.C. to power the electronic card using the L-N

terminals, at a max 50/60Hz frequency.

Use 24V to power the command devices and accessories.

Careful! The accessories cannot exceed 37W of overall power.

The card is ﬁtted with an amperometric device which constantly

monitors the motor’s drive. When the gate runs into an obstacle,

the amperometric sensor immediately detects the overload on

the drive and so inverts the gate’s movement:

- opens it if it is closing

- closes it if it is opening

Warning: after 3 obstacle detections, the gate stops when

in opening-mode and excludes automatic-closing mode; to

regain movement press the command button or use the remote

control.

All connections are protected by quick-fuses – see table.

The card handles the following functions:

- Automatic closing after an opening command;

- Warning light pre-ﬂashing;

- Obstacle detection when gate is still at any point;

- Constant monitoring of photocell operations.

- Opening/closing;

- Opening/closing in maintained action mode;

- partial opening;

- total stop.

Apposite trimmers regulate:

- The automatic closing’s running time;

- The partial opening;

- The amperometric device’s detection sensitivity, in both normal

and brake modes;

- the speed of both the normal gate run and the brake mode run.

Warning! Before acting on the machinery, cut off the main power

supply and disconnect any emergency batteries.

TECHNICAL INFORMATION

Power supply 230V - 50/60 Hz

Maximum power allowed 400 W

Absorption at rest 100 mA

Maximum power for 24V accessories 35 W

Insulation rating II

Pag.

10 - Manual code:

119BU50

119 B U 5 0 ver.

1.0

ENGLISH

Andere Handbücher für BX-246

Inhaltsverzeichnis

Andere CAME Toröffner Handbücher

CAME

CAME FROG series Bedienungsanleitung

CAME

CAME BKV1500P Bedienungsanleitung

CAME

CAME GARD series Bedienungsanleitung

CAME

CAME 8K01MP-0408 Bedienungsanleitung

CAME

CAME FAST 70 Bedienungsanleitung

CAME

CAME BX-P Bedienungsanleitung

CAME

CAME RLB Bedienungsanleitung

CAME

CAME FA70230CB Bedienungsanleitung

CAME

CAME 801XC-0180 Bedienungsanleitung

CAME

CAME BXV Series Bedienungsanleitung

CAME

CAME BKX12AGF Bedienungsanleitung

CAME

CAME RSDN002 Bedienungsanleitung

CAME

CAME STYLO ME Bedienungsanleitung

CAME

CAME BXV04AGS Bedienungsanleitung

CAME

CAME FA70230CB Bedienungsanleitung

CAME

CAME ATS-P3 KIT Bedienungsanleitung

CAME

CAME BXV Rapid Series Bedienungsanleitung

CAME

CAME FROG series Bedienungsanleitung

CAME

CAME FTL Series Bedienungsanleitung

CAME

CAME v6000 Bedienungsanleitung

CAME

CAME v6000 Bedienungsanleitung

CAME

CAME FA40230CB Bedienungsanleitung

CAME

CAME TOP-434EE Bedienungsanleitung

CAME

CAME FROGPLUS-S7 Bedienungsanleitung

Beliebte Toröffner Handbücher anderer Marken

Elite

Elite CSW200UL Bedienungsanleitung

SOMFY

SOMFY FX230 Bedienungsanleitung

Aprimatic

Aprimatic ONDA 500 Bedienungsanleitung

Turnstiles

Turnstiles FSW 900 Bedienungsanleitung

Erreka

Erreka BUL BL33 Betriebsanleitung

Erreka

Erreka VULCAN S Bedienungsanleitung

Beninca

Beninca R1-2 WBV Bedienungsanleitung

Erreka

Erreka VULCAN D Bedienungsanleitung

Motorline professional

Motorline professional FORT Bedienungsanleitung

Beninca

Beninca BOB5024 Bedienungsanleitung

AGA

AGA GATEMASTER 900 HD Bedienungsanleitung

Chamberlain

Chamberlain MotorLift HC280ML Bedienungsanleitung

SOMFY

SOMFY Dexxo RTS Pro Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Westfalia

Westfalia 85 27 06 Bedienungsanleitung

Extel

Extel VERA Bedienungsanleitung

Comunello Automation

Comunello Automation ABACUS 220 Bedienungsanleitung

Mighty Mule

Mighty Mule 200 E-Z GATE OPENER UL325 SERIES Bedienungsanleitung