CAME KRONO KR300 Bedienungsanleitung

CAME UNITED KINGDOM LTD

UNIT 3,

ORCHARD PARK INDUSTRIAL ESTATE,

TOWN STREET, SANDIACRE,

NOTTINGHAM NG10 5BP

TEL: 0115 921 0430

FAX: 0115 921 0431

INTERNET - www.cameuk.com

E-MAIL - [email protected]

TECHNICAL

HELPLINE

0115 921 0430

KRONO KIT

Installation Instructions

1) Left-hand motor unit

2) Right-hand motor unit

3) Control panel

4) Radio reveicer

5) Safety photocell

6) Key-operated selector switch

7) Flashing light

8) Receiving antenna

9) Photocell column

10) Radio transmitter

UNITED KINGDOM LTD.

INTRODUCTION

These instructions will show you how to install a KRONO gearmotor external

automatic opening system for wing gates.

Please read these instructions and diagrams carefully before starting any work.

Standard Installation

1) Left-hand motor unit

2) Right-hand motor unit

3) Control panel

4) Radio receiver

5) Safety photocell

6) Key-operated selector switch

7) Flashing light

8) Receiving antenna

9) Radio transmitter

UNDER NO CIRCUMSTANCES SHOULD THIS EQUIPMENT BE OPERATED UNLESS FITTED TO A GATE.

FAILURE TO COMPLY WILL INVALIDATE THE GUARANTEE.

INSTALLATION INSTRUCTIONS

CONTENTS

1) Stage 1:- Civil & Mechanical Section Page

1.1 BASIC HINGE GEOMETRY 3

1.2 BASIC CABLE LAYOUT 4

1.3 LOW VOLTAGE CABLE LAYOUT 5

1.4 ATTACHING THE REAR BRACKET 6

1.5 ATTACHING THE BRACKETS 8

2) Stage 2:- Wiring & Electrical

2.1 INSTALLING THE MOTORS 10

2.2 INSTALLING CENTRE STOPS 11

2.3 MANUAL RELEASE OF GATES 12

2.4 FITTING THE CONTROL PANEL IN THE CASING 13

2.5 WIRING THE MOTORS 14

2.6 WIRING THE SAFETY PHOTOCELLS 15

2.7 INSERTING THE FREQUENCY CARD 15

2.8 WIRING IN THE TUNED ANTENNA 16

2.9 CODING THE REMOTE CONTROLS 16

2.10 POWERING UP THE CONTROL PANEL 17

3) Stage 3:- Commissioning the Control Panel

3.1 INITIAL WIRING & CONTROL PANEL SETUP 18

3.2 OPENING & CLOSING THE GATES 19

3.3 CONTROL PANEL ADJUSTMENTS 20

3.4 AUTOMATIC CLOSE & SAFETY PHOTOCELLS 21

3.5 PROGRAMMING THE REMOTE CONTROLS TO THE CONTROL PANEL 22

4) Troubleshooting Guide 24

5) Technical Information

5.1 MOTOR TORQUE SETTINGS 26

5.2 ZA4 CONTROL PANEL DESCRIPTION 27

5.3 ZA4 WIRING DIAGRAM 28

5.4 CONTROL PANEL ADJUSTMENTS 29

5.5 ELECTRICAL CONNECTIONS 30

7) Contact Information

“Time marches on but Came automation equipment stands the test of time...”

STAGE 1

CIVIL & MECHANICAL SECTION

1.1 - Basic Hinge Geometry

Before beginning your installation of your KRONO system, check the following:

• Your gate piers or posts are sufficiently strong enough to support the gates and operators and the

gates swing freely and there is no friction between the moving parts.

• Measurement Cmust not be greater than the value shown below. If this is the case, it is necessary

to modify the pillar so that this measurement corresponds.

Dimension Cmust be no greater than 60mm for 90° opening and no greater than 50mm for a 120°

opening.

• Ensure that a centre stop is securely cemented into the ground. As a guide ensure that the centre

stop protrudes no more than 65mm. Any higher and it might catch the underside of a car.

Figure 1

Centre Stop

Pillar Pillar

Hinge Hinge

C C

1.2 - Basic Cable Layout

This diagram details the basic cable layout for a pair of motors.

The power supply to the control panel should be live and protected in accordance with the 16th edition

electrical regulations. The supply should be rated at a minimum of 6 amps. When installing wires

outdoors the cable approach to all devices must be from below to create a ‘drip-loop’ and thereby

avoid unneccessary water ingress.

Fig 2

When installing low voltage cable around the gateway it is advised to put all low voltage cable in either

ducting ot alkathene piping. All cable jointing should be carried out above ground.

Control panel

housing

240V AC 4 core

1.5mm SWA 4 core

1.5mm flex Joint box

1.3 - Low Voltage Cable Layout

All CAME accessories can be wired 0.2m stranded cable (burglar alarm type). The tuned antenna

should be wired with coaxial cable (RG59).

Fig 3

Tuned

Antenna

Flashing

light

Keyswitch

Doc-E safety

beams

2 core

1mm

8 core 0.2mm stranded

cable to all safety beams

Coaxial

cable

1.4 - Attaching the Rear Bracket

The rear bracket can be lengthened or shortened to suit individual installations, site and the position

of the gate (with respect to the bracket).

When attaching the rear bracket to the post or pillar use suitable expansion bolt or chemical fixings. If

fitting to a wooden post it is advised to use threaded bar bolted through the post for added strength.

Fig4

Wooden post and gate

Brick pillars

Type Opening A B C

Angle mm mm mm

90° 130 60

KRONO 130

120° 110 50

Attach the rear bracket while respecting distancesAand B between the hinge on the gate and the hole

in the centre of the bracket (which is used to hold the gear motor). To make the operation easier, the

KRONO installation kit contains two cardboard templates (for 90° and 120° openings). the rear bracket

is equipped with additional hole to make the fitting of the motor easier, or to change the opening angle

of the gate.

Fig 5

1.5 - Attaching the Brackets

With the gate closed, install the front bracket on the gate wing. The front bracket, when installed, must

be aligned along the horizontal axis of the rear bracket (see figure) and the distance between the

centre axes of the brackets must be 910mm.

Rear bracket

Levelling the brackets

Front bracket

E = 910

Fig 6

END OF INSTALLATION STAGE 1

BEFORE STARTING STAGE 2 - Wiring and Electrical

PLEASE CHECK THAT YOU HAVE CORRECTLY:

Ref Page

1. Prepared the cabling correctly 1.2 4

2. Correctly attached the brackets 1.4 6

NOW STAGE 1 IS FULLY COMPLETED YOU ARE READY TO BEGIN

STAGE 2 OF YOUR KRONO AUTOMATION KIT INSTALLATION.

Andere Handbücher für KRONO KR300

Inhaltsverzeichnis

Andere CAME Toröffner Handbücher

CAME

CAME BY-3500T Bedienungsanleitung

CAME

CAME Ferni Series Bedienungsanleitung

CAME

CAME Ati-S3 Bedienungsanleitung

CAME

CAME FROG series Bedienungsanleitung

CAME

CAME BXV1000GF Bedienungsanleitung

CAME

CAME F7024N Bedienungsanleitung

CAME

CAME KRONO KR300 Bedienungsanleitung

CAME

CAME FROG series Bedienungsanleitung

CAME

CAME 8K06SL-007 Bedienungsanleitung

CAME

CAME AMICO Series Bedienungsanleitung

CAME

CAME TOP Series Bedienungsanleitung

CAME

CAME DC00EGMA07 Bedienungsanleitung

CAME

CAME 806SL-0010 Bedienungsanleitung

CAME

CAME STYLO ME Bedienungsanleitung

CAME

CAME A 3000 Bedienungsanleitung

CAME

CAME GARD series Bedienungsanleitung

CAME

CAME FROG Bedienungsanleitung

CAME

CAME FA40230CB Bedienungsanleitung

CAME

CAME BK Series Bedienungsanleitung

CAME

CAME ATI series Bedienungsanleitung

CAME

CAME BY-3500T Bedienungsanleitung

CAME

CAME BK-1200P Bedienungsanleitung

CAME

CAME 803XA-0040 Bedienungsanleitung

CAME

CAME U 8700 Bedienungsanleitung

Beliebte Toröffner Handbücher anderer Marken

Elite

Elite CSW200UL Bedienungsanleitung

SOMFY

SOMFY FX230 Bedienungsanleitung

Aprimatic

Aprimatic ONDA 500 Bedienungsanleitung

Turnstiles

Turnstiles FSW 900 Bedienungsanleitung

Erreka

Erreka BUL BL33 Betriebsanleitung

Erreka

Erreka VULCAN S Bedienungsanleitung

Beninca

Beninca R1-2 WBV Bedienungsanleitung

Erreka

Erreka VULCAN D Bedienungsanleitung

Motorline professional

Motorline professional FORT Bedienungsanleitung

Beninca

Beninca BOB5024 Bedienungsanleitung

AGA

AGA GATEMASTER 900 HD Bedienungsanleitung

Chamberlain

Chamberlain MotorLift HC280ML Bedienungsanleitung

SOMFY

SOMFY Dexxo RTS Pro Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Westfalia

Westfalia 85 27 06 Bedienungsanleitung

Extel

Extel VERA Bedienungsanleitung

Comunello Automation

Comunello Automation ABACUS 220 Bedienungsanleitung

Mighty Mule

Mighty Mule 200 E-Z GATE OPENER UL325 SERIES Bedienungsanleitung