Campbell HC2S3 Bedienungsanleitung

HC2S3 Temperature

and Relative Humidity Probe

Revision: 10/12

Campbell Scientific, Inc.

Warranty

“PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. are

warranted by Campbell Scientific, Inc. (“Campbell”) to be free from defects in

materials and workmanship under normal use and service for twelve (12)

months from date of shipment unless otherwise specified in the corresponding

Campbell pricelist or product manual. Products not manufactured, but that are

re-sold by Campbell, are warranted only to the limits extended by the original

manufacturer. Batteries, fine-wire thermocouples, desiccant, and other

consumables have no warranty. Campbell's obligation under this warranty is

limited to repairing or replacing (at Campbell's option) defective products,

which shall be the sole and exclusive remedy under this warranty. The

customer shall assume all costs of removing, reinstalling, and shipping

defective products to Campbell. Campbell will return such products by surface

carrier prepaid within the continental United States of America. To all other

locations, Campbell will return such products best way CIP (Port of Entry)

INCOTERM® 2010, prepaid. This warranty shall not apply to any products

which have been subjected to modification, misuse, neglect, improper service,

accidents of nature, or shipping damage. This warranty is in lieu of all other

warranties, expressed or implied. The warranty for installation services

performed by Campbell such as programming to customer specifications,

electrical connections to products manufactured by Campbell, and product

specific training, is part of Campbell’s product warranty. CAMPBELL

EXPRESSLY DISCLAIMS AND EXCLUDES ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. Campbell is not liable for any special, indirect,

incidental, and/or consequential damages.”

Assistance

Products may not be returned without prior authorization. The following

contact information is for US and international customers residing in countries

served by Campbell Scientific, Inc. directly. Affiliate companies handle

repairs for customers within their territories. Please visit

www.campbellsci.com to determine which Campbell Scientific company serves

your country.

To obtain a Returned Materials Authorization (RMA), contact CAMPBELL

SCIENTIFIC, INC., phone (435) 227-9000. After an applications engineer

determines the nature of the problem, an RMA number will be issued. Please

write this number clearly on the outside of the shipping container. Campbell

Scientific's shipping address is:

CAMPBELL SCIENTIFIC, INC.

RMA#_____

815 West 1800 North

Logan, Utah 84321-1784

For all returns, the customer must fill out a "Statement of Product Cleanliness

and Decontamination" form and comply with the requirements specified in it.

The form is available from our web site at www.campbellsci.com/repair. A

completed form must be either emailed to repair@campbellsci.com or faxed to

(435) 227-9106. Campbell Scientific is unable to process any returns until we

receive this form. If the form is not received within three days of product

receipt or is incomplete, the product will be returned to the customer at the

customer's expense. Campbell Scientific reserves the right to refuse service on

products that were exposed to contaminants that may cause health or safety

concerns for our employees.

Table of Contents

PDF viewers: These page numbers refer to the printed version of this document. Use the

PDF reader bookmarks tab for links to specific sections.

1. Introduction.................................................................1

2. Cautionary Statements...............................................1

3. Initial Inspection .........................................................1

3.1 Ships With............................................................................................2

4. Quickstart ....................................................................2

4.1 Step 1 — Mount the Probe...................................................................2

4.2 Step 2 — Use SCWin Short Cut to Program Datalogger and

Generate Wiring Diagram.................................................................4

5. Overview......................................................................7

6. Specifications .............................................................8

6.1 Temperature Sensor .............................................................................9

6.2 Relative Humidity Sensor ..................................................................10

6.3 Default Settings and Digital Interface ................................................10

7. Installation.................................................................11

7.1 Siting ..................................................................................................11

7.2 Assembly and Mounting ....................................................................11

7.3 Wiring ................................................................................................11

7.4 Programming......................................................................................13

7.4.1 Example Programs using Single-Ended Measurement

Instructions ..............................................................................14

7.4.2 Example Programs using Differential Measurement

Instructions ..............................................................................17

7.5 Measuring Probes with Long Cables..................................................19

8. Sensor Maintenance .................................................20

9. Troubleshooting........................................................21

10. References ................................................................21

Table of Contents

Appendices

A. Absolute Humidity ..................................................A-1

A.1 Measurement Below 0°C................................................................. A-2

B. Changing the HC2S3 Settings ...............................B-1

B.1 HC2S3 Default Settings .................................................................. B-1

B.2 Software and Hardware Requirements ............................................ B-2

B.3 Changing the Temperature Range ................................................... B-2

B.4 Multiplier and Offsets for Temperature Range................................ B-3

C. HC2S3 Digital Communications ............................C-1

C.1 HC2S3 Digital Interface Specifications........................................... C-1

C.2 HC2S3 Communications Protocol................................................... C-1

C.3 RS-485 Communications using an MD485 RS-485 Interface......... C-3

C.4 RS-485 Communications using an SDM-SIO1 Serial I/O Module . C-5

Figures

4-1. HC2S3 and 41003-5 Radiation Shield on a tripod mast ...................... 3

4-2. HC2S3 and 41003-5 Radiation Shield on a CM200 Series Crossarm. 3

Tables

5-1. Recommended Lead Lengths .............................................................. 7

7-1. Connections for Single-Ended Measurements................................... 12

7-2. Connections for Differential Measurements...................................... 13

7-3. Temperature....................................................................................... 14

7-4. Humidity............................................................................................ 14

7-5. Wiring for Single-ended Measurement Examples............................. 14

7-6. Wiring for Differential Measurement Examples ............................... 18

A-1. Wiring for Vapor Pressure Examples.............................................. A-1

Model HC2S3 Temperature and Relative

Humidity Probe

1. Introduction

The HC2S3 is a rugged, accurate temperature/RH probe that is ideal for long-

term, unattended applications. The probe uses a Rotronic’s IN1 capacitive

sensor to measure RH and a 100 ohm PRT to measure temperature. For

optimum results, the HC2S3 should be recalibrated annually.

Before using the HC2S3, please study

•Section 2, Cautionary Statements

•Section 3, Initial Inspection

•Section 4, Quickstart

More details are available in the remaining sections.

2. Cautionary Statements

•Care should be taken when opening the shipping package to not damage or

cut the cable jacket. If damage to the cable is suspected, consult with a

Campbell Scientific applications engineer.

•Although the HC2S3 is rugged, it should be handled as a precision

scientific instrument.

•Do not touch the sensor element.

•The black outer jacket of the cable is Santoprene® rubber. This

compound was chosen for its resistance to temperature extremes, moisture,

and UV degradation. However, this jacket will support combustion in air.

It is rated as slow burning when tested according to U.L. 94 H.B. and will

pass FMVSS302. Local fire codes may preclude its use inside buildings.

3. Initial Inspection

•Upon receipt of the HC2S3, inspect the packaging and contents for

damage. File damage claims with the shipping company.

•The model number and cable length are printed on a label at the

connection end of the cable. Check this information against the shipping

documents to ensure the correct product and cable length are received.

•Refer to the Ships With list to ensure that parts are included (see Section

3.1). The HC2S3 probe and its calibration card are shipped in a small box,

with the box and PN 27731 Hex Plug attached to the cable.

Model HC2S3 Temperature and Relative Humidity Probe

3.1 Ships With

The HC2S3 ships with:

(1) 27731 Gill Radiation Shield Hex Plug

(1) Calibration Card

(1) Resource DVD

4. Quickstart

4.1 Step 1 — Mount the Probe

Review Section 7, Installation for complete instructions. To install the HC2S3,

you will need:

•41003-5 Radiation Shield

•27731 Hex Plug (ships with HC2S3)

1. Insert the 27731 hex plug that ships with the HC2S3 probe into the

underside of the 41003-5 base.

2. Attach the radiation shield to the tripod mast, crossarm, or tower leg using

the supplied U-bolt. See FIGURE 4-1 and FIGURE 4-2 for examples of

shield mounting.

3. Insert the probe into the radiation shield leaving about 2.5 cm (1 in.)

exposed below the hex plug.

4. Tighten the hex plug such that it compresses against the body of the

HC2S3 to hold it inside the radiation shield.

5. Attach the probe to the cable by aligning the keyed connectors, pushing

the connectors together and tightening the knurled ring.

6. Route the cable to the datalogger, and secure the cable to the mounting

structure using cable ties.

Model HC2S3 Temperature and Relative Humidity Probe

FIGURE 4-1. HC2S3 and 41003-5 Radiation Shield on a tripod mast

FIGURE 4-2. HC2S3 and 41003-5 Radiation Shield on a CM200 Series

Crossarm

41003-5

PN 27731 Hex Plug

U-bolt

CM200 Series Crossarm

Model HC2S3 Temperature and Relative Humidity Probe

4.2 Step 2 — Use SCWin Short Cut to Program Datalogger

and Generate Wiring Diagram

The simplest method for programming the datalogger to measure the HC2S3 is

to use Campbell Scientific's SCWin Short Cut Program Generator.

1. Open Short Cut and click on New Program.

2. Select a datalogger and scan interval.

Andere Handbücher für HC2S3

Inhaltsverzeichnis

Andere Campbell Messgerät Handbücher

Campbell

Campbell Nor150 Bedienungsanleitung

Campbell

Campbell CS135 Bedienungsanleitung

Campbell

Campbell CMP6-L Bedienungsanleitung

Campbell

Campbell Weatherpak M Bedienungsanleitung

Campbell

Campbell TGA200 Bedienungsanleitung

Campbell

Campbell HC2-S3-L Bedienungsanleitung

Campbell

Campbell CS650 Bedienungsanleitung

Campbell

Campbell TE525 Bedienungsanleitung

Campbell

Campbell SMP10 Bedienungsanleitung

Campbell

Campbell CMP6-L Bedienungsanleitung

Campbell

Campbell 247 Bedienungsanleitung

Campbell

Campbell LI200S-LC Bedienungsanleitung

Campbell

Campbell CS205 Bedienungsanleitung

Campbell

Campbell CS800-L Bedienungsanleitung

Campbell

Campbell CS106 Bedienungsanleitung

Campbell

Campbell cs215 Bedienungsanleitung

Campbell

Campbell CS805 Bedienungsanleitung

Campbell

Campbell KH20 Bedienungsanleitung

Campbell

Campbell Bowen Ratio Instrumentation Bedienungsanleitung

Campbell

Campbell CNR4 Bedienungsanleitung

Campbell

Campbell CNR4 Bedienungsanleitung

Campbell

Campbell CR23X Bedienungsanleitung

Campbell

Campbell HC2S3 Bedienungsanleitung

Campbell

Campbell WindSonic Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung