Campbell RainVUE Series Bedienungsanleitung

Revision: 11/2022

Campbell Scientific, Inc.

Table of contents

1. Introduction 1

2. Precautions 1

3. Initial inspection 1

4. QuickStart 2

5. Overview 4

6. Specifications 5

7. Installation 7

7.1 Wiring 8

7.2 Data logger programming 8

7.2.1 CRBasic programming 9

7.3 Siting 9

7.4 Mounting 9

8. Operation 15

8.1 SDI-12 measurements 15

8.2 SDI-12 extended commands 18

8.3 SDI-12 version 1.4 identify measurement commands and responses 20

8.4 Calculations 21

8.5 Device Configuration Utility 23

9. Maintenance and troubleshooting 27

9.1 Maintenance 28

9.1.1 Cleaning and replacing filters 28

9.1.2 Internal lithium battery 30

9.1.3 Updating the operating system 31

9.2 Troubleshooting 32

Table of Contents - i

Appendix A. Importing Short Cut code into CRBasic Editor 34

Appendix B. Calibration validation 35

Appendix C. SDI-12 sensor support 37

C.1 SDI-12 command basics 37

C.1.1 Acknowledge active command (a!) 38

C.1.2 Send identification command (al!) 38

C.1.3 Start verification command (aV!) 39

C.1.4 Address query command (?!) 39

C.1.5 Change address command (aAb!) 39

C.1.6 Start measurement commands (aM!) 40

C.1.7 Start concurrent measurement commands (aC!) 40

C.1.8 Start measurement commands with cyclic redundancy check (aMC! and aCC!) 42

C.1.9 Stopping a measurement command 42

C.1.10 Send data command (aD0! … aD9!) 42

C.1.11 Continuous measurement command (aR0! … aR9!) 43

C.1.12 Extended commands 43

C.2 SDI-12 transparent mode 44

C.2.1 Changing an SDI-12 address 44

C.3 References 46

Table of Contents - ii

1. Introduction

The RainVUE-series rain sensors are an ideal solution for many hydrological or meteorological

applications such as weather stations and flood warning systems. The models differ in their body

material; the RainVUE™10 has a molded UV-stabilized plastic body, and the RainVUE™20 has a

rugged aluminum body. In both models, a microprocessor corrects for rainfall intensity and

outputs an SDI-12 signal to communicate with any SDI-12 recorder, including Campbell Scientific

data loggers.

NOTE:

The RainVUE-series rain sensors are compatible with all data loggers that support SDI-12

communications. This manual focuses on Campbell Scientific CRBasic data loggers.

2. Precautions

lREAD AND UNDERSTAND the Safety section at the back of this manual.

lRainVUE-series is a precision instrument that must be handled with care.

lDuring installation, remove the piece of foam from under the tipping mechanism. This

foam should be saved and used whenever the sensor is transported.

lPull and remove the insulator tab used to prevent draining of the backup coin cell battery

during shipping and storage. The tab extends from the bottom of the RainVUE-series

interface to inside the RainVUE-series.

3. Initial inspection

lCheck the packaging and contents of the shipment. If damage occurred during transport,

immediately file a claim with the carrier. Contact Campbell Scientific to facilitate repair or

replacement.

lCheck model information against the shipping documents to ensure the expected products

and the correct lengths of cable are received. Model numbers are found on each product.

RainVUE-Series SDI-12 Precipitation Sensors 1

On cables and cabled items, the model number is usually found at the connection end of

the cable. Report any discrepancies immediately to Campbell Scientific.

4. QuickStart

A video that describes data logger programming using Short Cut is available at:

www.campbellsci.com/videos/cr1000x-data logger-getting-started-program-part-3 .Short

Cut is an easy way to program your data logger to measure the sensor and assign data logger

wiring terminals. Short Cut is available as a download on www.campbellsci.com . It is included

in installations of LoggerNet,RTDAQ, and PC400.

The following procedure shows how to use Short Cut to program the RainVUE-series:

1. Open Short Cut and click Create New Program.

2. Double-click the data logger model.

3. In the Available Sensors and Devices box, type RainVUE or find it in the Sensors >

Meteorological >Precipitation folder, and double-click RainVUE10/RainVUE20 Rain Gauge.

Enter the correct SDI-12 address for the sensor if it has been changed from the factory-set

default value. Type the numeric month and day for resetting the total accumulation, if you

want to do this. Otherwise, uncheck the Reset total intensity corrected accumulation once a

year box.

RainVUE-Series SDI-12 Precipitation Sensors 2

4. Click the Wiring tab, wire the sensor, then click OK.

5. Repeat steps three and four for other sensors you want to measure. Click Next.

6. In Output Setup, type the scan rate, a Table Name, and Data Output Storage Interval. Click

Next.

RainVUE-Series SDI-12 Precipitation Sensors 3

7. Select the output options.

8. Click Finish and save the program. Send the program to the data logger if the data logger

is connected to the computer.

9. If the sensor is connected to the data logger, check the output of the sensor in the data

display in LoggerNet,RTDAQ, or PC400 to make sure it is making reasonable

measurements.

5. Overview

The RainVUE-series funnels rainfall through a stainless-steel screen that traps debris, preventing

it from impeding the flow of precipitation. Rainfall flows through a nozzle into one of two bucket

halves. The internal tipping mechanism assembly rotates around a pivot point. The tipping

mechanism tips when the first bucket fills to a fixed calibrated level, then the tipping mechanism

moves the second bucket under the funnel. A magnet attached to the tipping mechanism

actuates a reed switch as the bucket tips. The outgoing water drains through outlets.

The aerodynamic design of the RainVUE-series reduces the amount of rain that wind carries away

from the collecting vessel. With traditional cylindrical tipping bucket rain sensors, wind can

reduce the rainfall catch by up to 20 percent. The RainVUE-series also includes a microprocessor

that corrects for rainfall intensity and outputs an SDI-12 signal.

During intense rainfall, extra water can accumulate in the bucket before the tipping mechanism

tips. The following graph shows the relationship between bucket volume and rainfall rate. The

RainVUE-series microprocessor corrects for the intensity sensitivity of the bucket mechanism.

RainVUE-Series SDI-12 Precipitation Sensors 4

This correction adjusts the rainfall rate based on the time between bucket tips. An electronic

timer precisely measures the time between tips.

Features:

lSuitable for nonfreezing precipitation and high intensity rain events

lDigital processing to correct for high intensity precipitation errors (see Specifications [p. 5])

lUnique aerodynamic shape increases measurement accuracy in windy conditions

lCompliance with WMO recommendations for accuracy and funnel area

lAdjustable mounting feet to simplify leveling

lTilt, internal temperature, and voltage measurements for remote diagnostics on the sensor

lCompatible with CRBasic data loggers: GRANITE-series, CR6, CR1000X, CR800-series,

CR350-series, CR300-series, CR3000, CR1000

6. Specifications

Sensor type: Tipping bucket with magnetic reed switch

Output: SDI-12 version 1.4

Response time: 0 s for M0! command and 1 s for M1! command

Tilt uncertainty: ±1 °

RainVUE-Series SDI-12 Precipitation Sensors 5

Temperature uncertainty: ±0.25 °C (±0.45 °F)

Supplyvoltageuncertainty: ±0.5 V

Operating temperature: 1 to 70 °C (34 to 158 °F); –40 to 70°C (–40 to 158°F) including

melting snow

Funnel diameter: 20.0 cm (7.87 in)

Height: 43.5 to 46.5 cm (17.1 to 18.3 in) with feet adjustment

Power: 6 to 18 VDC

Compliance: WMO compliant: 0.1 mm option only

View compliance documents at:

www.campbellsci.com/rainvue10

www.campbellsci.com/rainvue20

Table 6-1: RainVUE-series comparison

Specification RainVUE 10 RainVUE 20

Measurement range

0.01 inch option: 0 to

1200mm/hr (0 to 48in/hr)

0.1 mm option: 0 to 500mm/hr

(0 to 19.7in/hr)

0.2 mm option: 0 to

1000mm/hr (0 to 39.4in/hr)

0.01 inch option: 0 to

1200mm/hr (0 to 48in/hr)

0.1 mm option: 0 to 600mm/hr

(0 to 23.6in/hr

Precipitation amount

resolution

0.01 inch option: 0.254mm

(0.01in)

0.1 mm option: 0.1mm

(0.004in)

0.2 mm option: 0.2mm

(0.008in)

0.01 inch option: 0.254mm

(0.01in)

0.1 mm option: 0.1mm

(0.004in)

RainVUE-Series SDI-12 Precipitation Sensors 6

Table 6-1: RainVUE-series comparison

Specification RainVUE 10 RainVUE 20

Precipitation amount

measurement uncertainty

(mm/tip or in/tip)

0.01 inch option: ±1% at 0 to

1200mm/hr (0 to 48in/hr)

intensity

0.1 mm option: The larger of

0.1mm or 4% error at 0 to

500mm/h intensity (0 to

19.7in/h intensity)

0.2 mm option: < 4% at 0 to

1000mm/h intensity (0 to

39.4in/h intensity)

0.01 inch option: ±1% at 0 to

500mm/hr (0 to 20in/hr)

intensity

0.1 mm option: ±3.08% at 0 to

20mm/hr (0 to 0.8in/hr);

±3.6% at 20 to 600mm/hr (0.8

to 24in/hr) intensity

Precipitation intensity

measurement uncertainty

(mm/hr or in/hr)1

0.1 mm option: ≤3.5% at 0 to

300mm/h (7.9 to 11.8in/hr);

≤5% at 0 to 500mm/h (11.8 to

19.7in/hr)

0.2 mm option: ±4% at 200 to

1,000mm/hr (7.9 to 39.4in/hr)

intensity

0.01 inch option: ±1% at 0 to

500mm/hr (0 to 19.7in/hr)

intensity

0.1 mm option: ±3.58% at 20 to

600mm/hr (0.8 to 23.6in/hr)

intensity

Material White, ASA LI-911 plastic

Main collector body: 2mm

thick, powder-coated

aluminum

Base: LM6 marine-grade

aluminum

Weight 2 kg (4.5 lb) 6 kg (13 lb)

1Accuracy over the rain intensity range requires a mechanical calibration that is within 1 percent at a 1 in/hr

intensity. RainVUE-series sensors are calibrated at the factory to meet this specification but should be verified prior

to deployment; see Calibration validation.

7. Installation

If you are programming your data logger with Short Cut, skip Wiring (p. 8) and Data logger

programming (p. 8), as Short Cut does this work for you. See QuickStart (p. 2) for a Short Cut

tutorial.

RainVUE-Series SDI-12 Precipitation Sensors 7

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Campbell Messgerät Handbücher

Campbell

Campbell CM3 Bedienungsanleitung

Campbell

Campbell SR20-D2 Bedienungsanleitung

Campbell

Campbell CSAT3B Bedienungsanleitung

Campbell

Campbell 107 Bedienungsanleitung

Campbell

Campbell TE525 Bedienungsanleitung

Campbell

Campbell CSAT3 Bedienungsanleitung

Campbell

Campbell SMP10 Bedienungsanleitung

Campbell

Campbell Wind Monitor Series Bedienungsanleitung

Campbell

Campbell CS800-L Bedienungsanleitung

Campbell

Campbell CS616 Bedienungsanleitung

Campbell

Campbell VWANALYZER Bedienungsanleitung

Campbell

Campbell CR850 Bedienungsanleitung

Campbell

Campbell NR-Lite Bedienungsanleitung

Campbell

Campbell Nor150 Bedienungsanleitung

Campbell

Campbell CMP3 Bedienungsanleitung

Campbell

Campbell CS106 Bedienungsanleitung

Campbell

Campbell SoilVUE 10 Bedienungsanleitung

Campbell

Campbell TDR100 Bedienungsanleitung

Campbell

Campbell MMW-005 Bedienungsanleitung

Campbell

Campbell CS616 Betriebsanleitung

Campbell

Campbell DOT600 Bedienungsanleitung

Campbell

Campbell CS106 Bedienungsanleitung

Campbell

Campbell CS320 Bedienungsanleitung

Campbell

Campbell CS300 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung