Cane Creek Helm Bedienungsanleitung
SUSPENSION FORK INSTRUCTION MANUAL
2
3
Safety Warning Information
Tools Needed
Fork Features Overview
Crown Race Installation
Steerer Tube Cutting and Star Nut Installation
Stem Installation and Headset Preload
Front Brake and Cable Guide Screw/Cover Installation
D-Loc Axle Installation
Air Spring
Air Volume Adjustment
Damper Adjustments
Internal Travel Adjustment
Service and Maintenance Schedule
Warranty Information
04 ....
05 ....
06 ....
07 ....
08 ....
09 ....
10 ....
11 ....
13 ....
16 ....
18 ....
20 ....
25 ....
26 ....
Table of Contents
4
The fork is an important part of your
bicycle. Before installing and using
your new front fork, carefully read this
owner’s manual to learn the correct
installation and adjustment procedures
of this fork.
Warning
Improperly installed and/or adjusted
forks can cause serious harm or death
and may severely damage your bicycle.
Warning
A broken or malfunctioning fork may
cause loss of vehicle control and result
in SERIOUS INJURY OR DEATH. If the
fork ever loses oil, air or makes
unusual noises, stop riding and have
the fork inspected by a Cane Creek
Authorized Suspension Service Center
or call the Cane Creek Customer
Service Team.
Warning
Modification, improper service or use
of aftermarket replacement parts voids
the warranty and may cause the fork to
malfunction, resulting in loss of vehicle
Safety Warnings
control and SERIOUS INJURY OR
DEATH. Do not modify your bike frame
or fork. Use only genuine Cane Creek
Helm parts.
Follow service maintenance
recommendations. Fork service
should be performed by Cane Creek
Cycling Components or a Cane Creek
Authorized Suspension Service Center.
Visit www.canecreek.com or contact
us at 800-234-2725 to locate a Cane
Creek Authorized Suspension
Service Center.
5
Tools Needed
Tools Needed For Installation:
• Saw for cutting steerer
• Crownrace setter (Recommended
Cane Creek part code HST005)
• Star Nut Setter (Recommended:
Cane Creek part code .TL1100 and
.TL1102)
• 2.5mm hex wrench
Tools Needed For Maintenance:
• 2.5mm hex wrench
• 13mm wrench
• 18mm wrench
• 22mm wrench
• 30mm wrench
Specialized tools and materials are
needed for the installation of your Cane
Creek parts. Installation of Cane Creek
parts by a qualified bicycle mechanic is
highly recommended.
6
Fork Features Overview
Wheel Spacing Boost 110mm
Brake Connection Post Mount 180mm Rotor Size Adaptor Needed
For 200mm Rotor
Tire Clearance Maximum Tire
Size
Air Pressure Minimum = 30psi Maximum = 150psi Recommended
Sag 15-25%
Compression Low Speed 20 Clicks
Compression High Speed 10 Clicks
Rebound Low Speed 15 Clicks
Volume Reduction Indexed 8 Positions
Travel Reduction Indexed System 10mm Reducer Maximum 7
Reducers (100mm
Travel)
Max 65mm wide by 714mm tall. WARNING: Due
to wide variations in rim and tire widths, always
check tire clearance before riding. Remove air
and compress the fork completely to verify at
least 10mm of clearance across the complete
arc of the tire and the crown.
7
Crown Race Installation:
After installing a headset into the bicycle
frame, install the crown race included
with the headset onto the fork according to
the headset manufacturers instructions.
Crown Race Installation
8
Steerer Tube Cutting:
Measure the steerer tube twice and
cut to length according to the stem
manufacturers instructions.
WARNING: Do not install more than
30mm of spacers below the stem.
Star Nut Installation:
Use a star nut setter tool to install
a star nut into the steerer tube at a
depth of 15mm.
Steerer Tube Cutting and Star Nut Installation
9
Stem Installation and Headset Preload:
Install fork into frame and stem on
steerer tube. Tighten headset and
stem according to the manufacturer’s
instructions.
Stem Installation and Headset Preload
10
Front Brake and Cable Guide Installation
Front Brake and Cable Guide Screw/
Cover Installation:
Install brake caliper according to the
brake manufacturer’s instructions.
Route the front disc brake hose or
cable housing on the inside of the
lower fork leg through the disc brake
housing guide.
WARNING: Ensure that all bolts are
tightened to the correct torque and
that fork movement is not restricted by
improper assembly when the suspension
is fully compressed or extended.
Torque to 1Nm Max
Inhaltsverzeichnis
Andere Cane Creek Fahrradzubehör Handbücher
Cane Creek
Cane Creek Double Barrel Bedienungsanleitung
Cane Creek
Cane Creek THUDBUSTER ST Bedienungsanleitung
Cane Creek
Cane Creek Thudbuster LT Bedienungsanleitung
Cane Creek
Cane Creek CANE CREEK THUDBUSTER Bedienungsanleitung
Cane Creek
Cane Creek AngleSet EC44 Bedienungsanleitung
Cane Creek
Cane Creek eeSilk Systemhandbuch
Cane Creek
Cane Creek DROPT Service-Handbuch
Cane Creek
Cane Creek AD-12 Shock Bedienungsanleitung
Cane Creek
Cane Creek Helm MKII Bedienungsanleitung
Cane Creek
Cane Creek eeSilk Systemhandbuch
Beliebte Fahrradzubehör Handbücher anderer Marken
Sigma
Sigma BC 16.16 Bedienungsanleitung
Playcore
Playcore Dero Setbacks Bedienungsanleitung
VDO Cyclecomputing
VDO Cyclecomputing x3dw Bedienungsanleitung
Cateye
Cateye RAPID X2 Bedienungsanleitung
buratti meccanica
buratti meccanica Clorofilla Trail Bedienungsanleitung
Shimano
Shimano SG-8R20 Betriebsanleitung
