Canon MultiPASS F20 Handbuch

Set-Up Sheet

Unpack the machine and its components.

Check that you have the following:

NOTE

• A printer cable is not included.You must purchase a USB cable (less than 16 #/8 ft./5 m) to

connect your machine to a computer.

Black

BCI-24

MadeinJapan

BCI-24

MadeinJapan

Color

Machine

Multi-purpose tray

Printhead

PCMCIA card adapter

Ink tanks

(Black, color)

Power cord

Documentation

(Set-Up Sheet, Basic Guide,

Registration Card,

Extended Service Plan)

MultiPASS Suite software CD-ROM

Thank you for purchasing the Canon MultiPASS F20.

To get your machine ready for use, please follow the instructions in this Set-Up Sheet

before referring to any other documentation.

READ THIS SHEET FIRSTREAD THIS SHEET FIRST

Remove the shipping material from the machine.

1Place the machine on a flat surface.

2Remove all shipping tapes from the exterior of the machine.

NOTE

• DO NOT remove the USB label Aat this stage.

Connect the power cord.

NOTE

• Before turning on the power, make sure the document cover Ais closed.

Attach the multi-purpose tray and load paper.

1Insert the tabs on the bottom edge of the multi-purpose tray into the holes on

the machine as shown.

PLEASE WAIT

PUT IN CARTRIDGE

1Plug the power cord

into a socket.

2When you connect the

machine, the Alarm light blinks,

and the messages below

should appear in the LCD.

3If nothing appears

in the LCD, press

[ON/OFF] to turn

on the machine.

Approx. 30 seconds

NOTE

•Please note that the cartridge

(printhead and ink tanks) is

installed in steps 5 and 6.

USB label A

2Lift up the tray extension.

3Place a stack of paper (print side up) in the multi-purpose tray qand adjust the

paper guide Ato the width of the stack w.Make sure the stack does not exceed

the paper limit mark B.

NOTE

• When you are not printing, remove the paper stack from the multi-purpose tray and

close the tray.

4Open the paper output tray q,then pull out the tray extension w.

Printouts will exit the machine here.

NOTE

• When you are not printing, you can close the paper output tray.

Install the printhead.

IMPORTANT

•To turn off the machine, be sure to always press [ON/OFF].This will ensure that the

printhead is capped and prevent it from drying up.

•If you are not using the machine for a long period of time, we recommend that you

print (in black and color) or clean the printhead approximately once a month to

maintain the printhead in good working condition.

1Remove the tape q,then open the inner cover w.

• The printhead holder automatically moves to the left of the machine.

IMPORTANT

•Do not try to manually move or

stop the printhead holder.

•Do not touch any metal parts

inside the machine.

•Do not turn off the machine when

opening the inner cover.

2Remove the printhead from its packaging, then remove the orange protective

cap A.

IMPORTANT

• Do not touch the electrical contacts B.

3Raise the lock lever C,then gently slide the printhead into the holder.

Lower the lock lever.

IMPORTANT

• Do not touch the lock lever once the printhead has been installed.

Turn over to

continue

Turn over to

continue

Install the ink tanks.

1Start with the black ink tank. Remove the ink tank from its packaging, hold it as

shown below, then remove the protective cap A.

NOTE

•Do not shake or drop the ink tank as the ink may leak and

stain your clothes or hands.

•Do not attempt to reattach the protective cap Aonce

you remove it.

•Once you remove the protective cap A,do not touch the

ink port B.

2Insert the black ink tank into the right hand slot. Press firmly on the ink tank‘s tab

until it clicks into place.

3Repeat steps 1 and 2 to install the color ink tank in the left hand slot.

4Close the inner cover.

Be sure to now align the printhead as explained in step 7.

BCI-24

Color

BCI-24

Black

BCI-24

Black

BCI-24

Black

BCI-24

Ink Tank

Madein Japan

Black

Align the printhead.

NOTE

• If you will be installing the MultiPASS Suite software, you can also align the printhead

from the software. For details, see p. 9-7 of the Basic Guide.

1When the LCD Adisplays the following, press [Set].

The machine will print a horizontal line pattern, and the LCD will display:

2In column A on the printout, note which box has the most solid image. Note the

value next to this box and use [2] or [3] on the operation panel to enter it.

Then press [Set].

3Repeat step 2 for columns B to F.

After finishing the setup, the machine returns to standby mode.

100% LTR TEXT

PLAIN

Ex:

Most solid

box

Least solid

box

BAD

SAMPLE

GOOD

SAMPLE

Column A Value for column A

CHANGE H VALUE

A 0

ALIGN PRINT HEAD

PRESS SET KEY A

Install the software.

IMPORTANT

• DO NOT connect the USB cable before installing the software.

NOTE

• Windows 98/Me users: You need to have “Client for Microsoft Networks“ installed before

installing the MultiPASS Suite software. For details, refer to p. 10-1 of the Basic Guide.

• When installing the software in Windows XP or Windows 2000, log onto the system as a

member of the Administrator group.

• If you have previously installed an earlier version of the MultiPASS Suite software

(version 4.2 or earlier), you must remove it before installing this version. For details on

removing the software, refer to the documentation of the previous version.

1Make sure both your machine and computer are turned on.

2On your computer, close any open applications, including virus checkers.

3Insert the MultiPASS Suite CD-ROM into your CD-ROM drive.

• The setup program should start automatically. If it does not, double-click [My

Computer] in the Windows screen, double-click the CD-ROM icon, then double-click

[csplash] or [csplash.exe].

4When the next screen appears, click

INSTALL MULTIPASS SUITE.

5Follow the on-screen instructions.

6When the message below appears, remove the label Afrom the USB port B

located on the back of the machine. Then connect a USB cable C(not included)

to the machine and computer.

Windows 98/Me/2000 Windows XP

NOTE

•If you cannot continue with

the installation after

connecting the USB cable,

refer to p. 10-1 of the Basic

Guide.

CUSB label A

• Windows 98/Me/2000 users: Once connected, the USB driver will automatically be

installed.

• Windows XP users: Once connected, the “Found New Hardware Wizard” dialog box

appears. Click [Install the software automatically], then click [Next].

7Follow the on-screen instructions to complete installation.

If you wish to install any other software included in

the CD-ROM, click [Install Easy-PhotoPrint] or [Install

ScanSoft Omnipage SE].

8When installation is complete, restart your computer before using the MultiPASS

Suite software.

Once installed, the MultiPASS Toolbar will be displayed on the desktop:

For details on using the MultiPASS Toolbar, see p. 7-1 of the Basic Guide.

NOTE

• Remember to register your machine to ensure product support.The serial number is

located on the back of the machine.

Congratulations! You have now completed your machine

setup.

Where to from here...

Once you have completed all steps in this Set-Up Sheet, refer to the Basic Guide for

instructions on all functions of your machine. For comprehensive instructions on

the MultiPASS Suite software, refer to the Software Guide (included in the CD-ROM).

Part no. HT3-2117-000-V.2.0

Canon, MultiPASS, and BCI are trademarks of Canon Inc.

All other products and brand names are registered

trademarks or trademarks of their respective owners.

Specifications subject to change without notice.

PRINTED IN THAILAND

Andere Handbücher für MultiPASS F20

Inhaltsverzeichnis

Andere Canon Multifunktionsdrucker Handbücher

Canon

Canon Pixma MG3500 Series Einrichtungshandbuch

Canon

Canon IR3320i Bedienungsanleitung

Canon

Canon MAXIFY MB2750 Einrichtungshandbuch

Canon

Canon imageRUNNER ADVANCE 8105 Bedienungsanleitung

Canon

Canon 3301B002 Bedienungsanleitung

Canon

Canon imageRUNNER 3300 Bedienungsanleitung

Canon

Canon MultiPASS F30 Bedienungsanleitung

Canon

Canon imageRUNNER ADVANCE 4251 Bedienungsanleitung

Canon

Canon imageCLASS MF753Cdw Bedienungsanleitung

Canon

Canon IMAGERUNNER ADVANCE C5051 Bedienungsanleitung

Canon

Canon iR1019 Series Bedienungsanleitung

Canon

Canon DR-202 Gebrauchs- und Pflegehandbuch

Canon

Canon g3000 series Einrichtungshandbuch

Canon

Canon 1238P Technisches Datenblatt

Canon

Canon PIXMA MG5600 Series Einrichtungshandbuch

Canon

Canon MultiPASS L60 Montageanleitung

Canon

Canon imageCLASS MF4880dw Montageanleitung

Canon

Canon PIXMA MG8220 Series Bedienungsanleitung

Canon

Canon PIXMA MG5220 Series Bedienungsanleitung

Canon

Canon PIXMA MX850 Bedienungsanleitung

Canon

Canon PIXMA MP990 Bedienungsanleitung

Canon

Canon CFX-B380 IF Bedienungsanleitung

Canon

Canon PIXMA MP520 Bedienungsanleitung

Canon

Canon iR1600 Series Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung