CarLink CLBTLR Betriebsanleitung

EN-20180727-A

Rev Date: 20180727

This system must be installed by a professional.

COMPLETE INSTALLATION & PROGRAMMING GUIDE

NOTICE

The manufacturer will accept no responsability for any electrical damage resulng from

improper installaon of this product, be that either damage to the vehicle itself or to the

installed device. This device must be installed by a cered technician. Please review the

Installaon Guide carefully before beginning any work.

CLBTLR Digital RF Kit system

TABLE OF CONTENTS

HARDWARE PARTS ............................................................................................................................ 3

iDATASTART HCx.................................................................................................................................4

iDATASTART VWx................................................................................................................................ 6

iDATASTART BM or BZ ...................................................................................................................... 8

AKX, OEM or FLRS............................................................................................................................ 10

ADS-AL-CA / FL-CAN.......................................................................................................................12

COMPUSTAR CM7200 / POLARSTART PRS-16 ..................................................................... 14

COMPUSTAR CM6200 ......................................................................................................................16

COMPUSTAR DC2...............................................................................................................................18

COMPUSTAR DC3............................................................................................................................. 20

DBALL 2 ................................................................................................................................................22

DB3..........................................................................................................................................................24

4X10 - 5X10 - AF-D600 - ASD200 - ASD-600.......................................................................26

DS4 - DS4+...........................................................................................................................................28

PRESTIGE (E) Models...................................................................................................................... 30

PRESTIGE (Z) Models.......................................................................................................................32

PURSUIT (E) Models ........................................................................................................................ 34

CODE SYSTEMS..................................................................................................................................36

OLDER CODE SYSTEMS..................................................................................................................38

OMEGA RS-X70.................................................................................................................................40

OMEGA AL-XX70-B ......................................................................................................................... 42

DSE 503AIR 5R-85 ........................................................................................................................... 44

DSE iSTART2 - 3 ................................................................................................................................ 46

System LED Status & Protocol Reference Chart................................................................... 48

Reset Procedure ................................................................................................................................ 48

CREATE AN ACCOUNT

Before begining the installation and setting the conﬁgurations of a Carlink CLBTLR system, we

strongly recommend downloading the Application from the App store and create a user account.

a. Go to the App store (Apple) or Play store (Android) and Search for “Carlink CLBTLR”.

Download and install the Free Application.

b. Launch the newly installed SmartControl Application on your smartphone or tablet

c. Click “Create an Account”

d. Fill in all the required ﬁelds

e. Once done, Log into the Application using your email and your newly created password.

HARDWARE PARTS

XTX-3000

IVU-CAB-4W

HRN-CRF-02

RTX-3200

PARTS REQUIRED FOR INSTALLATION OF : iDATASTART HCx

XTX-3000 IVU-CAB-4W iDatastart HCx

STEP 1. CONFIGURE THE REMOTE STARTER

The ADS Weblink (ADS-USB) is required to properly conﬁgure the iDatastart HCx remote starter to accept

the RF kit system. When ﬂashing the iDatastart HCx remote starter, please follow this procedure in order

to conﬁgure correctly your remote starter.

a. Go to www.idatalink.com and click on “Flash your module”

b. Using the new Weblink configurator, Choose

vehicle Make, Year, Model, Trim.

c. In the Remote Configuration section, Select the Brand drop-

down and Choose “CONNECTED” and select the Connected RF

system you are using.

d. This will load a firmware starting with: “IDPP-XXX-XXX-XXX”

e. Click “Flash your device”

INSTALLATION, WIRING & PROGRAMMING GUIDE

Antenna: Cord length 9 feet

Installation:

Place antenna 3 inches

(minimum) from any obstructions

Orientation: Vertical; antenna

facing downwards (as seen in

diagram)

STEP 2. CONNECT

STEP 3. ADD A DEVICE/VEHICLE TO AN ACCOUNT

a. Download the App and Log into your account (see page 2 of this document for details)

b. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add

and conﬁgure your customers system inside your personal account. A system refers to the Antenna

being installed in the windsheild of the vehicle.

c. Before adding a system to your device, ensure the remote starter IS NOT armed/locked or in Valet mode

and set the ignition of the vehicle to the On position.

d. Then Tap to “Scan QR Code” and use the smartphone camera to scan the QR Code located on top of the

antenna.

e. Once connected, the system is in “Installer Mode”. Follow the on-screen instructions for conﬁguring the

system.

STEP 4. PRE-CONFIGURE THE APPLICATION EXPERIENCE FOR YOUR CUSTOMER

a. Start by setting the protocol of the antenna being used. This is acheived by selecting the Brand, Model

and protocol used inside the Remote starter. When done, click on “Conﬁrm”. System will now try to

communicate with the remote starter to conﬁrm that all settings related to protocol are valid.

b. Once back in the control panel, click on the Settings Gear at the top right of the screen and edit the

Vehicle name, conﬁgure the Auxiliaries that might have been added (if applicable) and click “OK” when

done. Then choose the vehicle to display inside the control panel in the VEHICLE IMAGE section and

click OK.

c. When your conﬁgurations are all completed, click “OK” at the top right corner. All Conﬁgurations will

take eect.

STEP 5. TESTING THE SYSTEM

When the system is connected and fully conﬁgured, testing can begin. Test all the application functions

(Start, Stop, Lock, Unlock, Auxiliaries, Etc.) When testing is completed, tap on the “installer icon” at the top

of control screen. When prompted Click “Yes, and delete system from account” since this is the installer

mode and not the End User mode. This will make the system “Ready for Customer Delivery”.

Also make sure that the Owners Card is handed to the Owner of the vehicle or attached to the vehicle

keychain. Doing this will ensure that the instructions on how to setup their App, Account and add the Sys-

tem is done correctly by using the system QR Code axed on the windsheild mounted antenna.

NOTE : UNDER ANY CIRCUMSTANCES, PLEASE DO NOT REMOVE THE QR CODE FROM THE ANTENNA!

INSTALLATION, WIRING & PROGRAMMING GUIDE

PARTS REQUIRED FOR INSTALLATION OF : iDATASTART VWx

XTX-3000 IVU-CAB-4W iDatastart VWx

STEP 1. CONFIGURE THE REMOTE STARTER

The ADS Weblink (ADS-USB) is required to properly conﬁgure the iDatastart VWx remote starter to accept

the RF kit system. When ﬂashing the iDatastart VWx remote starter, please follow this procedure in order

to conﬁgure correctly your remote starter.

a. Go to www.idatalink.com and click on “Flash your module”

b. Using the new Weblink configurator, Choose

vehicle Make, Year, Model, Trim.

c. In the Remote Configuration section, Select the Brand drop-

down and Choose “CONNECTED” and select the Connected RF

system you are using.

d. This will load a firmware starting with: “IDPP-XXX-XXX-XXX”

e. Click “Flash your device”

INSTALLATION, WIRING & PROGRAMMING GUIDE