Carrier KSACN0401AAA Bedienungsanleitung

Wired Remote Controller

7 Day Programmable

Ductless Systems

KSACN0401AAA (High Wall/Floor Console Models)

KSACN0501AAA (Ducted/Cassette Models)

INSTALLATION INSTRUCTIONS

NOTE: Read the entire instruction manual before installing the unit.

TABLE OF CONTENTS

PAGE

SAFETY CONSIDERATIONS 2...............................................

COMPATIBILITY TABLES 5.................................................

INSTALLATION ACCESSORY 6..............................................

INSTALLATION 8..........................................................

WIRE THE INDOOR UNIT 11................................................

APPENDIX 14.............................................................

SPECIFICATION 21........................................................

TECHNICAL INDICATION AND REQUIREMENT 21............................

SAFETY CONSIDERATIONS

Read these instructions thoroughly and follow all warnings or cautions included in the literature and

attached to the unit. Consult local building codes and National Electrical Code (NEC) for special

requirements.

Recognize safety information. This is the safety−alert symbol !

! . When you see this symbol on the

unit and in instructions or manuals, be alert to the potential for personal injury. Understand these signal

words: DANGER, WARNING, and CAUTION. These words are used with the safety−alert symbol.

DANGER identifies the most serious hazards which will result in severe personal injury or death.

WARNING signifies hazards which could result in personal injury or death. CAUTION is used to

identify unsafe practices which may result in minor personal injury or product and property damage.

NOTE is used to highlight suggestions which will result in enhanced installation, reliability, or

operation.

EQUIPMENT DAMAGE HAZARD

Failure to follow this caution may result in equipment damage or improper operation.

Excessive torque can break the flare nut depending on installation conditions.

CAUTION

EQUIPMENT DAMAGE HAZARD

Failure to follow this warning could result in personal injury or death.

Before beginning any modification or installation of this kit, ensure the main electrical

disconnect is in the OFF position. Ensure power is disconnected to the fan coil unit. On

some systems both the fan coil and the outdoor unit may be on the same disconnect. Tag

the disconnect switch with a suitable warning label. There may be more than one to

disconnect.

CAUTION

INSTALLATION

Entrust the distributor or authorized professionals to install the unit. Installation by

unskilled persons may lead to improper installation, electric shock, or fire.

Re−installation must be performed by authorized professionals.

Non−compliance may lead to electric shock or fire.

CAUTION

NOTE: Save this manual for future reference.

SThis manual provides a detailed description of the precautions that the user should be

mindful of during operation.

STo ensure correct service of the wired controller, read this manual carefully before

using the unit.

SKeep this manual, after reading it, for future reference.

NOTE:

1. Do not install the unit in a location vulnerable to flammable gas leaks. Once flammable gases

are leaked and left around the wire controller, a fire may occur.

2. Do not operate with wet hands or allow water to enter the wire controller, otherwise an electric

shock may occur.

3. The wiring should be a compatible connection cable for the current wired controller.

Otherwise, electric leakage or heating may occur and result in a fire.

4. The specified cables shall be applied in the wiring. No external force may be applied to the

connection wire terminal. Otherwise a wire cut and heating may occur and result in a fire.

COMPATIBILITY TABLES

Table 1—Wired Controller: KSACN0401AAA

HIGH WALL* FLOOR CONSOLE**

40MAQB09B--1 619PAQ009BBMA 40MHHQ09---1 40MHHC09---1 40MBFQ09---3

40MAQB12B--1 619PAQ012BBMA 40MHHQ12---1 40MHHC12---1 40MBFQ12---3

40MAQB09B--3 619PEQ009BBMA 40MHHQ09---3 40MHHC09---3

40MAQB12B--3 619PEQ012BBMA 40MHHQ12---3 40MHHC12---3

40MAQB18B--3 619PEQ018BBMA 40MHHQ18---3 40MHHC18---3

40MAQB24B--3 619PEQ024BBMA 40MHHQ24---3 40MHHC24---3

40MAQB30B--3 619PEQ030BBMA

40MAQB36B--3 619PEQ036BBMA

NOTE: *Compatible with indoor units 40MAQ/619P*B starting with Serial Number 0216V10001.

** Compatible with indoor units starting with Serial Number 0117V10001.

Units built prior this serial number would require a Control Board Replacement on the Indoor unit.

Table 2—Wired Controller: KSACN0501AAA

CASSETTE DUCTED STYLE

40MBQB09C--3 619REQ009CBMA 40MBQB09D--3 619REQ009DBMA

40MBQB12C--3 619REQ012CBMA 40MBQB12D--3 619REQ012DBMA

40MBQB18C--3 619REQ018CBMA 40MBQB18D--3 619REQ018DBMA 40MBDQ18---3

40MBCQ09---3 40MBQB24D--3 619REQ024DBMA 40MBDQ24---3

40MBCQ12---3 40MBQB36D--3 619REQ036DBMA 40MBDQ36---3

40MBCQ18---3 40MBQB48D--3 619REQ048DBMA 40MBDQ48---3

INSTALLATION ACCESSORY

PREPARATION BEFORE INSTALLATION

1. Confirm the following required parts have been supplied (see Table 3).

Table 3—Parts

No. NAME QTY. REMARKS

1Wired controller 1

2Installation and owner's manual 1

3Screws 3M4X20 (for mounting on the wall)

4Wall plugs 3For mounting on the wall

5Screws 2M4X25 (for mounting on the switch box)

6Plastic screw bars 2For fixing on the switch box

7 Battery 1

8The connection cable 119 feet (6 meters)

9Adapter Board 1Required for High Wall 40MAQ/619P*B

10 Display Board 1Required for High Wall 40MAQ/619P*B

NOTE:

Extension wire available through RCD (Replacement Components). Part Number: 17401204000769.

For 40MHH High Wall follow the instructions on the installation manual of the indoor unit.

2. Prepare the following assemblies on site.

Table 4—Assemblies

No. NAME QTY. (EMBEDDED

INTO WALL)

SPECIFICATION (ONLY

FOR REFERENCE) REMARKS

1Switch box 1

2Wiring tube (insulating sleeve and

tightening screw) 1

WIRED CONTROLLER INSTALLATION PRECAUTION

1. This manual provides the wired controller installation method. Refer to the wiring diagram in

this installation manual to wire the wired controller with the indoor unit.

2. The wired controller works in a low voltage loop circuit. Do not connect directly to 208/230V

and 460V. Do not wire this kind of wire into a loop. Wiring clearance between the configured

tubes should range 11.81−19.69 inches (30−50 cm) or above.

3. The shielded wire of the wired controller must be properly grounded.

NOTE: Upon completion of the wired controller connection, do not use a tramegger to test the

insulation.

CONTROLLER DIMENSIONS

123mm

(4.8”)

120mm

(4.7”)

18.5mm

(0.7”)

83.5mm

(3.3”)

46mm

(1.8”)

62mm

(2.4”)

Fig. 1 - Wired Remote Controller Dimensions

red

black

yellow

brown

red

black

yellow

brown

Insert of the

mainboard CN40

Wire controller Indoor unit mainboard

4-Core Shield Cable, the length

is decided by installation

-----------------------------------

Fig. 2 - Wiring Connection Diagram

INSTALLATION

KSACN0401AAA

Adapter board

Display board

4-core shielding wire

The connection

cable

CN101

Fig. 3 - Installation of KSACN0401AAA for High Wall Indoor Models

1. Install the Adapter Board and the Display Board on the High Wall (See the Appendix for

instructions).

2. Connect the female joint of the wires group from the adapter board with the male joint of the

connective wires group. Next, connect the other side of the adapter board with the display

board (see Fig. 3).

3. Connect the other side of the connective wires group with the male joint of the wires group

leads from the wire controller (see Fig. 3).

Mainboard

4-core shielding wire

KSACN0501AAA

The connection cable

CN40

Fig. 4 - Installation of KSACN0501AAA for Cassette, Ducted Indoor Models

1. Connect the female joint of the wires group from the mainboard with the male joint of the

connective wires group (see Fig. 4).

2. Connect the other side of the connective wires group with the male joint of the wires group

leads from the wire controller (see Fig. 4).

WIRED CONTROLLER UPPER PART REMOVAL

1. Insert a flat screwdriver into the slots in the lower part of the wire controller (2 places).

2. Remove the upper part of the wire controller (see Fig. 5).

Slots

Fig. 5 - Slots

NOTE: The PCB is mounted in the upper part of the wired controller. Be careful not to

damage the board with the screwdriver.

FASTEN THE WIRED CONTROLLER BACK PLATE

1. For surface mounting, fasten the back plate on the wall with the 3 screws (M4x20) and plugs

(see Fig. 6).

Back plate

Screws (M4×20)

Fig. 6 - Fasten Back Plate

2. For switch box mounting, fasten the back plate on the switch box with 2 screws (M4x25) and

fasten it on the wall with 1 screw (M4x20) (see Fig. 7).

Back plate

Screws (M4×20)

Fig. 7 - Flush Mounting

NOTE: Place on a flat surface. Be careful not to distort the wire controller’s back plate by

over−tightening the mounting screws.

Andere Handbücher für KSACN0401AAA

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Carrier Thermostat Handbücher

Carrier

Carrier Connect Bedienungsanleitung

Carrier

Carrier CRC2 - NTC Bedienungsanleitung

Carrier

Carrier 33CS450-01 Bedienungsanleitung

Carrier

Carrier Infinity SYSTXCCITW01 Bedienungsanleitung

Carrier

Carrier User interface Comfort Module Series Betriebsanleitung

Carrier

Carrier EDGE PRO 33CS2PPRH-01 Bedienungsanleitung

Carrier

Carrier P/N 33CSSN2-MH Bedienungsanleitung

Carrier

Carrier Comfort series Bedienungsanleitung

Carrier

Carrier 33CS Anleitungen und Rezepte

Carrier

Carrier Infinity Control Home Bedienungsanleitung

Carrier

Carrier Debonair 33CS250-01 Bedienungsanleitung

Carrier

Carrier Performance TP-PAC Bedienungsanleitung

Carrier

Carrier Comfort Pro 33CSCNACHP-01 Bedienungsanleitung

Carrier

Carrier TOTALINE GOLD P274-0150 Bedienungsanleitung

Carrier

Carrier AQUAZONE 50QE900-250FS Bedienungsanleitung

Carrier

Carrier TC -PAC Bedienungsanleitung

Carrier

Carrier TSTATCCPS701 Bedienungsanleitung

Carrier

Carrier 33CS220-LA Bedienungsanleitung

Carrier

Carrier 33CSCPACHP-01 Bedienungsanleitung

Carrier

Carrier A99068 Montageanleitung

Carrier

Carrier 33CS400-01 Bedienungsanleitung

Carrier

Carrier 33CS450-01 Bedienungsanleitung

Carrier

Carrier Infinity Control Home Montageanleitung

Carrier

Carrier 33AW-CS1 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung