CAS CI-1580A Bedienungsanleitung

Contents

1. Introduction........................................................

2. Specifications.....................................................

3. Front Panel Descriptions..................................

4. Rear Panel Descriptions................................ 10

5. Installation ........................................................

6. Calibration ....................................................... 12

7. Set-up............................................................... 19

8. Interface ........................................................... 36

1.Introduction

■Introduction

This product as an indicator for weighing instruction and control is designed for the most

suitable use of any meters (packer, weigh separator, platform scale, various tensile and

compression test equipment)that can be applied in the widest way throughout industries.

This product ensures communications with external devices such as computers as it basically

installs an RS-232C port.

In addition, this product can be conveniently used for the weighing control as it basically has

three relay outputs necessary for control (applicableonly if there is relay out).

Please utilize all the functions in this product sufficiently as you can use the device properly

with good knowledge of this manual before you use this product.

■Features

·Measurestoscreenoffexternalnoises

·Built-inself-diagnosisandself-recoveryfunctionsfromfailure

·Externalresolution:1/20,000

·Electrostaticdatamemory

·2built-inexternalrelayinputterminals(zero,tare/tareremoval)

·Datamemory

·24VofinputpowersupplycanbeusedwiththeuseofDCpowersupplyregardlessof

polarity(500mA<TransType>ormoreisrecommended)

·FAC(FullAutoCalibration)methodforcalibration

·EquivalentinputmethodforCalibration

·BasicinstallationofRS-232C

·Option:RS-422/485

·Option:I/V-OUT

■Cautions

·Donotdroporapplysevereshockstotheproduct.

·Do not install the product with high voltage or severe electric noises.

·Do not install the produce with direct sunlight or severe vibrations.

·Connect the product with external peripheral devices after turning off the power switch.

·Keep theproduct fromwateror rain.

■Accessories

·Productmanual

·Option(separateoptionforanyaddition):1EAofadaptor(DC24V/500mA)

2. Specifications

■Analog Part & A/D Conversion

Inputsensitivity

0.3㎶/D

Adjustmentrangeof Zero

-0.6mV∼+1.5mV

LoadCellExcitationVoltage

DC10V(±5V)

TemperatureCoefficient

Zero : ±10 PPM / ℃

SPAN:±10PPM/℃

Input Noise

±0.6㎶P.P

InputImpedance

Over10㏁

A/Dconversionmethod

∆∑

A/DInternalResolution

520,000Count(19bit)

A/DConversionRate

200times/Sec

Non-linearity

0.01%FS

■Digital Part

Display

7-Segment,5digitREDFND

Charactersize:12.7(H)×7.3(W)mm

Division

×1,×2,×5,×10,×20,×50

BelowZeroIndication

“-“ MinusSign

DecimalPoint

0,0.0,0.00,0.000

Status Lamp

Stable,Zero,High,Low,OK, Hold, Comm

FunctionKey

ZERO,TARE,SET,ENTER

■General Specification

Power

DC24V/About500mA(TransType)

OperatingTemperature

Range

-5℃~+40℃

OperatingHumidity

Range

Under85% Rh (Non-condensing)

ProductSize

(W)100 X(H)52X(D)125 (mm)

ProductWeight

About 450g

■Options

Option-1

RS-422/485

Option–2

I-OUT(4~20mA)

Option-3

V-OUT(0~10V)

3. Front Panel Descriptions

■DISPLAY (CI-1580A)

■Display

·Weight:Thecurrentweightattheindicatorisdisplayed.

- Wheneverthesetkeyispressed,thevalueforhighlimit,lowlimitordifferencesis

displayed.

■Display of Status

·STABLE:Itisdisplayedwhentheweightisstable.

·ZERO: It is displayed when the weight is “0”.

·LOW:Itisdisplayedwhentheweightisthelowlimitorless.

·HIGH:Itisdisplayedwhentheweightisthehighlimitormore.

·OK:Itisdisplayedwhentheweighingiscompleted.

·HOLD:Itisdisplayedwhiletheweightisbeingheld.

·COMM(RTxD):Itisdisplayedwhiletheproductiscommunicatingwithotherdevices.

■Key Operations

Key

Descriptions

It is used to set the weight display to „0‟ within a range of maximum weight

(CAPA)defined bytheuser.

(However, it is operated within the input range by the user to „Equipment Set‟ „08‟

(Set forZeroRange).

It is used to set the tare to „0‟ after a container is put on the weighing tray.

(However, it is operated within the input range by the user to „Equipment Set‟ „09‟

(Set forTareRange)

It is usedfor the input of lowlimit (SP1) and highlimit (SP2).

It isused toenterthesetvalue.

■Special Key Operations

Key

Descriptions

①It is used to increasethenumeric value.

②It isused tofinishthesettingundertheSET,CALstatus.

①It is usedtomove the positionof anumeric value.

②It is usedtomove to TEST MODE underthe SET, CAL status.

①It is used to increase the unique number (F XX) in „Equipment Set‟.

②When it is pressed under the „SET, CAL‟ status, it moves to „Equipment Set‟

(SETUP).

①It is used to enter (save) the set value by the user in the „Weight Calibration‟

function.

②When it is pressed under the „SET, CAL‟ status, it moves to „Weight Calibration‟

(Calibration).

4. Rear Panel Descriptions

①POWER

-DC IN:AsthisproductusesDCpowersupply,DC 24V

(500mATransType) canbe usedfor thisproduct.

②OPTION

-RS-232C(3PConnecterI/FCommunications)(BasicSpecifications)

-RS-422/485(4PConnecterI/FCommunications)(SeparateOption)

-4~20mA(0~10V)(2PConnecterI/F)(SeparateOption)

③EXTERNAL

INPUT

1+EXC - Loadcellconnectionterminal

2 -EXC - Loadcellconnectionterminal

3+SIG - Loadcellconnectionterminal

4 –SIG - Loadcellconnectionterminal

5SHIELD - Loadcellconnectionterminal

6F.G - Grounding

7PWR - DC IN 24V (input regardless of polarity)

8PWR -

9,10,11 ICOM,IN1~2(INPUT)–RefertoF11setforF-FunctionMode

12,13,14,15 0COM, OUT1~3(OUTPUT) –Refer to F21 set for F-Function

Mode

②

③

5. Installation

■External Dimension & Panel Cutting Size

(External Dimension Xmm)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CAS Skala Handbücher

CAS

CAS BF-1255B Bedienungsanleitung

CAS

CAS BFA-2 Bedienungsanleitung

CAS

CAS ECB Series Bedienungsanleitung

CAS

CAS CL5500 Series Bedienungsanleitung

CAS

CAS S2000JR Bedienungsanleitung

CAS

CAS PD-II Bedienungsanleitung

CAS

CAS DL-30 Bedienungsanleitung

CAS

CAS LP-II Montage- und Wartungsanleitung

CAS

CAS CBX Bedienungsanleitung

CAS

CAS CT100 Series Bedienungsanleitung

CAS

CAS ED Series Bedienungsanleitung

CAS

CAS CL5000 Series Bedienungsanleitung

CAS

CAS CL5000 Series Bedienungsanleitung

CAS

CAS PD-II Bedienungsanleitung

CAS

CAS MW-II Series Bedienungsanleitung

CAS

CAS DB-1 Bedienungsanleitung

CAS

CAS GBF-1251 Bedienungsanleitung

CAS

CAS CCB Series Bedienungsanleitung

CAS

CAS ER PLUS SERIES Bedienungsanleitung

CAS

CAS FW500 Bedienungsanleitung

CAS

CAS LP-II Montage- und Wartungsanleitung

CAS

CAS Poscale Bedienungsanleitung

CAS

CAS LP-II Bedienungsanleitung

CAS

CAS HS-1 Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung