CAS DL-30 Bedienungsanleitung
CONTENTS
PRECAUTIONS 4
PREFACE 6
NAMES AND FUNCTIONS 6
INSTALLATIONS 8
OPERATIONS 9
1. Power Source 9
2. General Weighing 9
3. Weighing with Tare 10
4. HOLD Function 10
5. Auto Power Off 11
6. Mode 11
ERROR MESSAGES 14
SPECIFICATIONS 14
4
Do not subject the scale to sudden
temperature changes.
PRECAUTIONS
Place the scale on a flat and stable
surface.
Do not subject the platter to sudden
shocks. This scale must be installed in a dry
and liquid free environment.
Make sure that you plug your scale into the proper power outlet.
Plug into a power outlet 30 minutes before operations.
5
Keep the scale away from strong EMI noises may cause incorrect weight
readings.
If the scale is not properly
level, please adjust the 4 legs
at the bottom of the scale
(turn legs clockwise or
counterclockwise) so as to
center the bubble of the
leveling gauge inside the
indicated circle.
Leveling gauge
6
PREFACE
NAMES AND FUNCTIONS
Thank you for purchasing our CAS DL series.
These series have been designed with CAS reliability, under rigid quality control
and with outstanding performance. Your specialty departments can enjoy these
high quality reliable CAS products.
We believe that your needs will be satisfied and you will have reliability.
This manual will help you with proper operation and care of the DL series.
Please keep this handy for future reference.
OVERALL VIEW
PLATTER
LEVELING GAUGE
DISPLAY
KEYBOARD
ADJUSTING BOLT
7
DISPLAY AND KEYBOARD
CAL
ZERO TARE HI GO LO
LB
kg
PCS
ON
OFF
ZERO TARE HOLD
ON
OFF
ZERO TARE SET MODE
HOLD
INC
KEY FUNCTIONS
ON
OFF
ZERO
TARE
HOLD
Turn on or off the display.
Used to set the zero point.
Used to enter a tare weight and used to cancel a tare weight.
If the weight is not stable, the display shows the average weight.
DESCRIPTIONSKEYS
8
INSTALLATIONS
1. Insert and fasten the bracket support assembly screws.
2. Connect the load cell wire and power line to head.
3. Insert the support cover into the support.
4. Insert and fasten the screws.
9
USING ADAPTOR Convert switch to AC 110V or 220V.
Use only adaptor DC 9V/300mA.
Connect the adaptor into AC outlet and
insert plug into the jack on the scale.
Press the ON/OFF key.
1. Power Source
USING BATTERIES
Prepare six pieces of DC 1.5V(CM) batteries.
Open the cover in the back of the scale and insert the batteries as shown in
Fig.1.
Close the cover and press the ON/OFF key then the scale is on.
If you have low battery, the display shows “Err-5” as Fig.2 and the scale is off
automatically.
OPERATIONS
+
-
+
-
+
-
+
-
+
-
+
-
Fig.1 Fig.2
+
-
Fig.3
kg
ZERO
kg
2. General Weighing
When the display is not zero though there is nothing on the platter, press the
ZERO key.
Place a commodity on the
platter. Remove the commodity
from the platter.
10
kg
ZERO TARE
kg
TARE
kg
ON
OFF
ZERO TARE HOLD
ZERO TARE
kg
ZERO
kg
ON
OFF
ZERO TARE HOLD
3. Weighing with TARE
Tare is the weight of container being used for a commodity.
The TARE key subtracts the weight of the container.
4. HOLD Function
When the weight is not stable, press the HOLD key.
The display shows the “HOLd” and then average weight.
Place a container on the
platter. Press the TARE key.
Remove the commodity and
container from the platter. Press the TARE key.
Place a commodity in the
container.
11
ON
OFF
ZERO TARE SET MODE
HOLD
INC
Auto power off function set
Initial display
Auto power off function reset
5. Auto Power Off
Auto-Power off function lengthen the battery life.
When you don’t operate the scale, this function makes the power OFF
automatically.
Turn off the scale.
While pressing the ZERO key, press the ON/OFF key then you will see the
display below.
6. Mode
While pressing the ON/OFF key, press the ZERO key to change the function.
If you want to use this function, set to YES.
While pressing the ON/OFF key, press the TARE key to go to normal mode.
If you don’t use the scale for more than 3 minutes, the scale is turned off
automatically.
If your scale has 6 keys, there are 5
modes.
(Reference How to Change Mode.)
12
KEY FUNCTIONS
SET
HOLD
INC
MODE
When the weight is not stable, the display will show average weight.
Used to increase the number to enter the limit value.
Used to save the limit value and select the mode.
Used to change the mode.
DESCRIPTIONSKEYS
How to Change Mode
If you want to use counting mode, press the MODE key until the display shows
“tyPE4” and then press the SET key.
Counting Mode
To count samples, you have to set the quantity.
Change the mode to counting mode and press the SET key.
Put 10 samples on the platter and press the SET key.
If the weight of sample is greater than the 0.5% of the full capacity, the counting
function will be performed. otherwise, the display will show “-----”.
The display will show “Put 20” or “Put 50” to request more samples if the loaded
weight is less than 0.5% of the full capacity.
Put 20 or 50 samples and press the SET key.
To perform counting function, the weight of 50 samples must be greater than 0.5%
of the full capacity.
kg
LB
kg
LB
PCS
Weighing mode (kg) Weighing mode (lb) Limit mode (kg)
Limit mode (lb) Counting mode
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere CAS Skala Handbücher
CAS
CAS AP Series Bedienungsanleitung
CAS
CAS AP Plus-MX Bedienungsanleitung
CAS
CAS SW-1N Bedienungsanleitung
CAS
CAS WEIGHING SOLUTION SWII PLUS Series Bedienungsanleitung
CAS
CAS LDT Bedienungsanleitung
CAS
CAS SW-1S Series Bedienungsanleitung
CAS
CAS CT100 Series Bedienungsanleitung
CAS
CAS HS-1 Bedienungsanleitung
CAS
CAS RW-2000Z Bedienungsanleitung
CAS
CAS BW-6 Bedienungsanleitung
CAS
CAS EB Series Bedienungsanleitung
CAS
CAS CL3500 Series Bedienungsanleitung
CAS
CAS MWP Bedienungsanleitung
CAS
CAS LP-1000N Series Bedienungsanleitung
CAS
CAS NC-1 Bedienungsanleitung
CAS
CAS TP-15 Bedienungsanleitung
CAS
CAS LP-1000N Series Handbuch
CAS
CAS CCB Series Bedienungsanleitung
CAS
CAS BI Series Bedienungsanleitung
CAS
CAS EB Series Bedienungsanleitung
