Casablanca 99148 Bedienungsanleitung

Compatible with:

2xxxx Types A - Z

51000-58999 fan series

59500-59999 fan series

Select Casablanca Fans

Models 99148, 99150, 99159

MA020-01 • 03/05/14

Energy Star Low Prole

Integrated Kit

Energy Star Low Prole

Integrated Kit

Installation Manual

MA020-01 • 03/05/14

1.888.830.1326

Your light kit is compatible with most ceiling fans. The light kit will attach to the fan’s

switch housing. Begin on page 3 where you will choose the type of switch housing that

most closely resembles the one on your fan. From there, you will be directed to the set

of assembly instructions that are appropriate for installing the light kit to your fan.

Read entire installation instructions carefully before

beginning installation and save these instructions.

BEFORE YOU BEGIN

Switch

Housing

READ AND SAVE THESE INSTRUCTIONS

This product conforms to UL Standard 507.

WARNINGS

w.1 - To reduce the risk of re, electrical shock, or personal injury,

mount fan directly from building structure and/or an outlet box marked

acceptable for fan support of 70 lbs. (31.8 kg) and use the mounting screws

provided with the outlet box.

w.2 - To avoid possible electrical shock, before installing or servicing your

fan, disconnect the power by turning off the circuit breakers to the outlet

box and associated wall switch location. If you cannot lock the circuit

breakers in the off position, securely fasten a prominent warning device,

such as a tag, to the service panel.

c.1 - All wiring must be in accordance with national and local electrical codes

ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualied electrician.

CAUTIONS

Turn Power

OFF

MA020-01 • 03/05/14

1.888.830.1326

If your fan’s switch housing cap

resembles this one, remove the cap

screws with a Phillips head screwdriver.

Then follow the TYPE-A ASSEMBLY

INSTRUCTIONS on pages 4-5.

Switch

Housing

Cap

Screw

WHICH ASSEMBLY METHOD WILL I USE?

Switch

Housing

Cap

Switch

Housing

Screw

Choose one of the four images below that most closely resembles the switch

housing on your fan; then follow the instructions under the image.

If your fan’s switch housing cap resembles

this one, remove the whole switch

housing by removing the switch housing

screws with a Phillips head screwdriver.

Remove the two cap screws from the

inside of the switch housing. Reinstall

the switch housing. Tighten the switch

housing screws. Then follow the TYPE-A

ASSEMBLY INSTRUCTIONS on pages 4-5.

If your fan’s switch housing cap resembles

this one, remove the whole switch

housing by removing the switch housing

screws with a Phillips head screwdriver.

Remove the plug button using a standard

screwdriver. Then follow the TYPE-C

ASSEMBLY INSTRUCTIONS on pages 8-9.

Switch

Housing

Screw

Plug

Button

If your fan’s switch housing cap resembles

this one, remove the whole switch

housing by removing the switch housing

screws with a Phillips head screwdriver.

Remove the plug button. Then follow the

TYPE-B ASSEMBLY INSTRUCTIONS on

pages 6-7.

Switch

Housing

Screw

Plug

Button

MA020-01 • 03/05/14

1.888.830.1326

TYPE-A ASSEMBLY INSTRUCTIONS

Partially install the two mounting screws

into the bottom of the lower switch housing.

Lift the light kit up to meet the lower switch

housing. Wrap keyhole slots around the screws

and twist counterclockwise. Tighten screws.

Keyhole

Slots

Mounting

Screw

Using the single pin connectors, connect

the black or blue wire from the fan to the

black wire from the light kit. Connect the

white wire from the fan to the white wire

from the light kit.

Mounting

Screw

3 4

If your fan does not have pin connectors on

the wires coming from the switch housing,

install the wiring harness provided. Using

the provided wire connectors connect the

white wire from the fan to the white wire

from the wire harness and connect the

black or blue wire from the fan to the black

wire from the wire harness.

Do not allow the light kit to hang

only by the wire connections!

Wire

Connector

Switch

Housing

MA020-01 • 03/05/14

1.888.830.1326

Installing the globe- Position the

indentations in the outer rim of the

globe so that they line up with the tabs

on the inside surface of the light xture

rim. Carefully lift the globe up inside the

light xture as far as it will go. Rotate the

globe in a clockwise direction until it is

held tightly in place by the four tabs.

Install a light bulb in each socket.

Turn Power

Installing the pull chain pendant -

Attach the pull chain pendant to the

end of the short chains coming from the

switch housing and the light kit.

Turn power on. Your

installation is complete!

TYPE-A ASSEMBLY INSTRUCTIONS (CONTINUED)

Bulb

Indentation

Tab

MA020-01 • 03/05/14

1.888.830.1326

TYPE-B ASSEMBLY INSTRUCTIONS

Using the single pin connectors, connect

the black or blue wire from the fan to the

black wire from the light kit. Connect the

white wire from the fan to the white wire

from the light kit.

Feed the wires through the center hole in

the switch housing, the washer, and the

nut. Then install the switch housing by

twisting clockwise onto the threaded rod.

Install the washer and nut onto threaded

rod and tighten securely.

Lift the light kit assembly up so that the

screw holes in the lower switch housing

line up with the holes in the upper switch

housing. Install the switch housing

screws and tighten securely.

Switch

Housing

Screw

Wire

Connector

Switch

Housing

If your fan does not have pin

connectors on the wires coming from

the switch housing, install the wiring

harness provided. Using the provided

wire connectors connect the white

wire from the fan to the white wire

from the wire harness and connect the

black or blue wire from the fan to the

black wire from the wire harness.

Do not allow the light kit to hang

only by the wire connections!

MA020-01 • 03/05/14

1.888.830.1326

TYPE-B ASSEMBLY INSTRUCTIONS (CONTINUED)

Installing the globe- Position the

indentations in the outer rim of the globe so

that they line up with the tabs on the inside

surface of the light xture rim. Carefully lift the

globe up inside the light xture as far as it will

go. Rotate the globe in a clockwise direction

until it is held tightly in place by the four tabs.

Indentation

Tab

Install a light bulb in each socket.

Turn Power

Turn power on. Your

installation is complete!

5 6

Bulb

Installing the pull chain pendant -

Attach the pull chain pendant to the

end of the short chains coming from the

switch housing and the light kit.

MA020-01 • 03/05/14

1.888.830.1326

TYPE-C ASSEMBLY INSTRUCTIONS

Feed the wires through the center hole in

the switch housing. Then using the single

pin connectors, connect the black or blue

wire from the fan to the black wire from

the light kit. Connect the white wire from

the fan to the white wire from the light kit.

Lift the lower switch housing up so that the

screw holes line up with the holes in the

upper switch housing. Install the switch

housing screws and tighten securely.

Lift the light kit up, tucking the wires into

the hole in the switch housing. Install the

center stem of the light kit into the lower

switch housing by turning the threaded

rod clockwise into the threaded hole.

Continue turning until tight.

Upper

Switch

Housing

Threaded

Rod

Wire

Connector

Switch

Housing

If your fan does not have pin connectors on

the wires coming from the switch housing,

install the wiring harness provided. Using

the provided wire connectors connect the

white wire from the fan to the white wire

from the wire harness and connect the

black or blue wire from the fan to the black

wire from the wire harness.

Do not allow the light kit to hang

only by the wire connections!

1 2

Lower

Switch

Housing

Switch

Housing

Screw

MA020-01 • 03/05/14

1.888.830.1326

TYPE-C ASSEMBLY INSTRUCTIONS (CONTINUED)

Installing the globe- Position the indentations

in the outer rim of the globe so that they line

up with the tabs on the inside surface of the

light xture rim. Carefully lift the globe up

inside the light xture as far as it will go. Rotate

the globe in a clockwise direction until it is

held tightly in place by the four tabs.

Indentation

Install a light bulb in each socket.

Turn Power

Turn power on. Your

installation is complete!

Tab

5 6

Bulb

Installing the pull chain pendant -

Attach the pull chain pendant to the

end of the short chains coming from the

switch housing and the light kit.

MA020-01 • 03/05/14

1.888.830.1326

TROUBLESHOOTING

Lights don’t come on.

• Make sure that the bulbs are properly installed.

• Make sure power switch is on.

• Pull the pull chain to make sure it is on.

• Check the circuit breaker to ensure the power is turned on.

• Check the pin connections in the light kit.

• Refer to the fan manual for locating the fan’s wiring. Verify that the light and power wires are

correctly connected to the ceiling and the light kit.

If you have problems installing or operating your light kit, do not return this product

to the dealer. Call our Consumer Affairs Hotline.

888-830-1326

2-YEAR ENERGY STAR LIGHT KIT WARRANTY

The Hunter Fan Company/Casablanca Fan Company makes the following warranty to the

original user or consumer purchaser of each Hunter/Casablanca Energy Efcient Light Kit:

If your Hunter/Casablanca Energy Efcient Light Kit fails at any time within two years after

the date of sale due to a defect in material or workmanship, labor to repair the defect will be

provided free of charge at our nearest service center or our service department in Memphis,

TN. You will be responsible for all labor costs after this two-year period.

This warranty is voided if this product is not purchased in the U.S.A. or Canada.

This warranty excludes and does not cover defects, malfunctions or failures of any product

which were caused by repairs by persons not authorized by us, use of parts or accessories

not authorized by us, mishandling, improper installation, modications or damage to the

light xture while in your possession, or unreasonable use, including failure to provide

reasonable and necessary maintenance. IN NO EVENT SHALL HUNTER FAN COMPANY BE

LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.

SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS

OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE

ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER

RIGHTS THAT VARY FROM STATE TO STATE.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Casablanca Wohnraumbeleuchtung Handbücher

Casablanca

Casablanca ATAMO Bedienungsanleitung

Beliebte Wohnraumbeleuchtung Handbücher anderer Marken

JONATHAN Y

JONATHAN Y JYL5019A Bedienungsanleitung

JONATHAN Y

JONATHAN Y JYL6007A Bedienungsanleitung

Philips

Philips Ledino 31606/11/16 Bedienungsanleitung

Salus

Salus UG600 Bedienungsanleitung

Safavieh Lighting

Safavieh Lighting CANDRI TBL4427A Bedienungsanleitung

Hunter

Hunter Bullet Spotlight Kit Gebrauchsanweisung

Philips

Philips 405441213 Bedienungsanleitung

Philips

Philips Halogen Light Bedienungsanleitung

Pentair

Pentair GLOBRITE Bedienungsanleitung

Philips

Philips 55592-30-16 Bedienungsanleitung

Livoo

Livoo Night light Bedienungsanleitung

Schwaiger

Schwaiger NFL45 Bedienungsanleitung

FRITZ HANSEN

FRITZ HANSEN AQ01 PLUG-IN Bedienungsanleitung

MOOD

MOOD CORSIN JY-16 Bedienungsanleitung

Safavieh Lighting

Safavieh Lighting KREMP TBL4409A Bedienungsanleitung

JONATHAN Y

JONATHAN Y JYL8019 Bedienungsanleitung

XTRASUN

XTRASUN XTDEOKT1 Bedienungsanleitung

Inspire

Inspire Lana YF3306-M Wartungshandbuch