Celestron TRAVEL SCOPE 60 DX Bedienungsanleitung

#22007

QUICK SETUP GUIDE

GUIDE DE DÉMARRAGE RAPIDE

KURZANLEITUNG ZUR EINRICHTUNG

GUIDA RAPIDA ALLA CONFIGURAZIONE

GUÍA DE INSTALACIÓN RÁPIDA

60 DX

ENGLISH | 1

Unpack your telescope and verify that all parts are present. Your

Travel Scope 60 DX includes: a telescope tube, a tripod and

mount head, two eyepieces, a 3x Barlow lens, a finderscope, an

erect image diagonal, a smartphone adapter, a Bluetooth shutter

remote, a Robert Reeves’

Lunar Landscapes

book download card,

and a travel backpack.

To extend the tripod’s central column, turn the locking knob

counterclockwise, lift up the tripod head until it is at the desired

height and turn the locking knob clockwise to secure.

Rotate the mounting platform so it is horizontal and tighten the knob

to secure it.

To set up the tripod, spread the legs outward until they are fully

extended and push down on the center leg brace.

Loosen the knob on the side of the tripod head mounting platform

and rotate the platform 90 degrees so it is standing vertically.

Remove the cap from the focuser end of the telescope tube and

make sure the two thumbscrews do not protrude into the opening.

Extend the legs of the tripod by unlocking the three tripod lock levers

on each leg. Pull each leg section all the way out and push the lever

on each lock downward to secure it in place.

Match the threaded bolt in the mounting platform to the threaded

hole on the bottom of the telescope tube and thread the two together.

Do not overtighten. This should be snug, but not tight.

Locate the erect image diagonal and remove the plastic covers. Insert

the barrel of the diagonal into the focuser and secure in place by

tightening the set screws.

QUICK SETUP GUIDE

#22007

ENGLISH

12 3

4 65

8 97

60 DX

2| ENGLISH

Insert the barrel of the 20mm eyepiece into the diagonal and tighten

the set screw.

Remove the lens cap from the front of the telescope. To observe,

look through the eyepiece as shown. Focus the image by turning the

knobs below the focuser.

To move the scope right and left, hold a tripod leg with one hand

while the other hand uses the panning handle to move the scope.

The azimuth locking screw can be loosened or tightened to adjust the

tension to your preference.

Remove the knurled nuts on the threaded posts at the focuser end

of the telescope tube.

For additional magnification, you can use the included 3x Barlow

lens. Place the Barlow lens between the diagonal and the eyepiece.

To move the scope up and down, rotate the entire pan handle

counterclockwise and use the handle to point the scope in the

direction you want to view. Rotate the pan handle clockwise to

lock it in place.

Locate the finderscope and remove the plastic caps on the front and

back lens. Orient the finderscope so that the larger lens is facing

towards the front of the tube as shown. Place the finderscope over the

posts on the tube and replace the knurled nuts to secure it in place.

For more information on this product or to download

the instruction manual, please visit the respective

product page on celestron.com

SOLAR WARNING: Never attempt to view the sun

through any telescope without a proper solar filter.

NEED ASSISTANCE?

Contact Celestron Technical Support

celestron.com/pages/technical-support

10 11

13 14

ENGLISH | 3

Use the phone clamp knob to open the phone holder

so that your phone fits inside. Tighten it to secure your

phone in place.

Turn on the phone and open your camera app. Make

sure the flash is turned off.

Loosen the knob on the bottom of the adapter that

secures the phone clamp to the eyepiece clamp. Slide

the phone clamp up and down and rotate it left and

right until your camera is looking down through the

eyepiece of the telescope. Tighten the knob on the

bottom of the adapter to secure it in place.

Use the telescope’s focuser to adjust focus of your

camera. Snap the image using your app.

USING THE

Smartphone Adapter

Open the eyepiece clamp and place it around the body

of the eyepiece. Tighten the clamp until it’s secure.

4 5

4| ENGLISH

Press and hold the button on the remote for 5 seconds.

A blue light will turn on and, after a few seconds, start

to blink. The remote is now in pairing mode.

Using the Bluetooth settings on your phone, pair the

device called “GBshutter”.

Open your camera app. Press the button on the

remote to trigger the shutter on your phone.

If your camera is in video mode, you can press the

button once to start recording and again to stop

the recording.

4 5

USING THE

Bluetooth

Remote

To insert or replace the battery, place your thumb

in the center of the back cover, pressing inward and

sliding downward remove the battery door. The CR2032

battery should be inserted with the positive (+) side

facing upward. Replace the cover.

123

ENGLISH | 5

CENTER THE TARGET

IN THE EYEPIECE

Look through the telescope using your lower powered

eyepiece. Move the telescope until the object you

chose lies in the center of the view. If the image is

blurry, gently turn the focus knobs until it comes into

sharp focus.

LOOK THROUGH FINDERSCOPE

Once the object is centered in your 20mm eyepiece, look

through the finderscope and locate the crosshair reticle.

ADJUST THE FINDERSCOPE

Without moving the telescope, use the three finger

knobs on the finderscope bracket to move the finder

around in the bracket until the crosshair appears over

the same object you are observing in the telescope’s

20mm eyepiece.

TIP: Try adjusting one screw at a time. Loosen

one screw by half a turn and tighten

another by the same amount to ensure the

finderscope is securely held in place.

YOUR FINDERSCOPE IS

NOW ALIGNED!

It should not require realignment unless it is bumped

or dropped.

The finder is one of the most important parts of your telescope. It helps you

locate objects and center them in the eyepiece. The first time you assemble your

telescope, you need to align the finder to the telescope’s main optics. It’s best to

do this during the day*.

* SOLAR WARNING! Never attempt to view the sun through any telescope

without a proper solar filter!

ALIGNING THE

FINDERSCOPE

CHOOSE A TARGET

Take the telescope outside during the day and find an

easily recognizable object, like a streetlight, license

plate or sign. The object should be as far away as

possible, but at least a quarter mile away.

2Low Power Eyepiece

Focus Knobs

6| ENGLISH

With the Moon visible in the sky, set up your telescope

with the 20mm eyepiece installed.

Look through the telescope’s 20mm eyepiece.

Gently turn the focus knobs to adjust the sharpness

of the image.

You can view many other celestial objects, such as

planets, star clusters and nebulae using this same

technique if you know where to find them in the

night sky.

Celestron’s free SkyPortal app for iOS and Android can

help you locate and identify a wide array of celestial

objects quickly and easily.

The best and easiest target for you to try to view first is the Moon. Try

observing the Moon at different points in its phase cycle. The best time

to view the Moon is from two days after a New Moon up to a few days

before a Full Moon. During this period, you will be able to see the most

detail in the craters and lunar mountain ranges.

YOUR FIRST NIGHT OUT-

THE MOON

To get a closer view of the Moon, loosen the set

screws on the focuser and remove the 20mm eyepiece.

Replace it with your 8mm eyepiece and tighten the set

screws to secure it in place. The 8mm eyepiece will

give you significantly more magnification, making the

Moon appear much larger.

NOTE: You may need to adjust the focus

knobs when you change eyepieces, so

make sure you are getting the sharpest

image possible.

Move the telescope so that it is roughly pointing

toward the Moon.

Look through the finderscope and locate the crosshair

reticle. Continue moving the telescope until the

crosshair appears over the Moon.

CONGRATULATIONS!

YOU HAVE NOW OBSERVED YOUR

FIRST CELESTIAL OBJECT!

Low Power Eyepiece

Focus Knobs

4 55

8mm 20mm

ENGLISH | 7

SAFETY INSTRUCTIONS

• Risk of explosion if battery is replaced by an incorrect type.

• The included battery is not rechargeable.

• Please use the battery in its original purpose to avoid causing the battery to short circuit. When the conductive material is connected directly to the

battery positive and negative will cause a short circuit.

• Do not use a damaged battery.

• Keeping the battery in an extremely cold or very hot location can result in shortened battery life.

• When replacing the battery, please refer to the instruction manual and pay attention to the positive and negative direction of battery.

• Do not put the battery in the fire. Dispose of the battery according to local regulations.

FCC IDENTIFIER: 2A2FG-X9

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Product design and specifications are subject to change without prior notification. This product is designed and intended for use by those 14 years

of age and older.

celestron.com/pages/technical-support

Telephone: 1(800) 421-9649

2835 Columbia Street • Torrance, CA 90503 U.S.A

07-21

FRANÇAIS | 1

Déballez votre télescope, et vérifiez que toutes les pièces sont

présentes. Votre Travel Scope (télescope de voyage) 60 DX

comprend : un tube de télescope, un trépied et une tête de

monture, deux oculaires, une lentille de Barlow 3x, un chercheur,

un renvoi coudé, un adaptateur pour téléphone intelligent, une

télécommande Bluetooth de déclencheur d’appareil photo, une

carte de téléchargement du livre

Lunar Landscapes

par Robert

Reeve et un sac à dos.

Pour étendre la colonne centrale du trépied, faites tourner la molette

de verrouillage dans le sens inverse des aiguilles d'une montre, levez

la tête du trépied jusqu’à ce qu’elle ait atteint la hauteur désirée puis

faites tourner la molette de verrouillage dans le sens des aiguilles

d'une montre.

Faites tourner la plateforme de la monture pour la positionner à

l’horizontale et serrez la molette pour la maintenir en place.

Pour installer le trépied, écartez les pieds vers l’extérieur jusqu’à

ce qu’ils soient complètement étendus et appuyez sur l’entretoise

centrale.

Desserrez la molette sur le côté de la plateforme de la monture située

sur la tête du trépied et faites-la pivoter de 90 degrés jusqu’à ce

qu’elle soit à la verticale.

Retirez le capuchon de l’extrémité du système de mise au point du

tube du télescope, et vérifiez que les deux vis à main ne dépassent

pas dans l’ouverture.

Étendez les pieds du trépied en desserrant les trois leviers situés sur

chaque pied. Tirez chaque section des pieds au maximum et appuyez

sur le levier de chaque pied vers le bas pour le serrer.

Positionnez le boulon fileté de la plateforme de la monture sur le

pas de vis situé sur le dessous du tube du télescope, et vissez-les

ensemble. Ne serrez pas excessivement. La connexion doit être

ferme, mais doit permettre le mouvement.

Trouvez le renvoi coudé dans la boîte et retirez les capuchons de

plastique. Insérez le barillet du renvoi coudé dans le système de mise

au point et fixez-le en serrant les vis à main.

GUIDE DE DÉMARRAGE RAPIDE

#22007

FRANÇAIS

60 DX

12 3

4 65

8 97

2| FRANÇAIS

Insérez le barillet de l'oculaire de 20 mm dans le renvoi coudé et

serrez les vis.

Retirez le capuchon de la lentille de l'avant du télescope. Lorsque

vous observez, regardez dans l'oculaire comme illustré. Faites le point

sur l'image en faisant tourner les molettes sous le système de mise

au point.

Pour orienter le télescope vers le haut ou vers le bas, faites tourner la

poignée d’orientation dans le sens inverse des aiguilles d’une montre

et pointez dans la direction désirée avec cette dernière. Faites tourner

la poignée d’orientation dans le sens des aiguilles d’une montre pour

fixer dans la direction désirée.

Retirez les écrous striés des tiges filetées de l'extrémité du tube du

télescope comportant le système de mise au point.

Pour obtenir un grossissement plus élevé, vous pouvez utiliser la

lentille de Barlow x3 incluse. Placez la lentille de Barlow entre le

renvoi coudé et l’oculaire.

Trouvez le chercheur dans la boîte et retirez les capuchons de

plastique de l'avant et de l'arrière de la lentille. Orientez le chercheur

de manière à ce que l’objectif plus grand soit orienté vers l'avant du

tube, comme illustré. Positionnez le chercheur sur les supports du

tube et remettez les écrous striés en place pour le fixer.

Pour orienter le télescope vers la droite et la gauche, tenez un pied

du trépied d’une main, et de l’autre, utilisez la poignée d’orientation

pour déplacer le télescope. La vis de verrouillage d’azimut peut être

desserrée ou serrée pour régler la résistance comme désiré.

Pour en savoir plus sur ce produit, ou télécharger

le mode d’emploi, visitez la page dédiée sur

celestron.com.

AVERTISSEMENT SUR LE SOLEIL : N’essayez

jamais d’observer le soleil à l’aide d’un télescope sans

utiliser un filtre solaire adéquat.

BESOIN D'ASSISTANCE?

Contactez le support technique de Celestron

celestron.com/pages/technical-support

10 11

13 14

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Celestron Teleskop Handbücher

Celestron

Celestron National Park Foundation ExploraScope 60AZ Bedienungsanleitung

Celestron

Celestron PowerSeeker 127AZ Bedienungsanleitung

Celestron

Celestron 52228 Bedienungsanleitung

Celestron

Celestron OmniXLT AZ Bedienungsanleitung

Celestron

Celestron 52201 Bedienungsanleitung

Celestron

Celestron FirstScope 114EQ Bedienungsanleitung

Celestron

Celestron Travel Scope 50 Bedienungsanleitung

Celestron

Celestron AstroMaster 90 EQ Bedienungsanleitung

Celestron

Celestron FirstScope 114EQ Bedienungsanleitung

Celestron

Celestron Discovery expedition Travel Scope 60 Bedienungsanleitung

Celestron

Celestron PowerSeeker2 70 Bedienungsanleitung

Celestron

Celestron PowerSeeker 114EQ Bedienungsanleitung

Celestron

Celestron STAR HOPPER Bedienungsanleitung

Celestron

Celestron FirstScope 114 Bedienungsanleitung

Celestron

Celestron SKY PRODIGY 102 Bedienungsanleitung

Celestron

Celestron 22405 Bedienungsanleitung

Celestron

Celestron Advanced VX 91519 Bedienungsanleitung

Celestron

Celestron 31030 Bedienungsanleitung

Celestron

Celestron PowerSeeker 60 EQ Bedienungsanleitung

Celestron

Celestron PowerSeeker 50 Bedienungsanleitung

Celestron

Celestron Ultima 2000 Bedienungsanleitung

Celestron

Celestron NexImage 95518 Bedienungsanleitung

Celestron

Celestron Advanced VX 12031 Bedienungsanleitung

Celestron

Celestron ASTRO FI 127 MAK Bedienungsanleitung

Beliebte Teleskop Handbücher anderer Marken

Meade

Meade 81005 Condor Bedienungsanleitung

Meade

Meade 114 EQ-DS Bedienungsanleitung

Meade

Meade LX200 CLASSIC Bedienungsanleitung

Leica

Leica 82 HD Bedienungsanleitung

EASTCOLIGHT

EASTCOLIGHT 9920 Bedienungsanleitung

zoomion

zoomion Genesis 200 EQ Bedienungsanleitung

TEC

TEC APO 140 Bedienungsanleitung

Orion

Orion 7832 Bedienungsanleitung

Carson

Carson Skelescope SK-100 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER VIRTUOSO Bedienungsanleitung

Orion

Orion EZ Finder 7228 Bedienungsanleitung

cassini

cassini C-JRS Bedienungsanleitung

nedis

nedis SCTE5060WT Bedienungsanleitung

Meade

Meade Polaris 60EQ-D Bedienungsanleitung

PlaneWave

PlaneWave CDK700 Bedienungsanleitung

William Optics

William Optics Synta Crayford Bedienungsanleitung

Orion

Orion FUNSCOPE Bedienungsanleitung

Levenhuk

Levenhuk Skyline Travel Bedienungsanleitung