Central Pneumatic 93216 Bedienungsanleitung

52 Pcs Air Tool Kit

(Impact Wrench / Die Grinder Set)

3491 Mission Oaks Blvd. / Camarillo, CA 93011

No portion of this manual or any artwork contained herein may be reproduced in any

shape or form without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353.

Assembly and Operating Instructions

93216

Due to continuing improvements, actual product may dlffer slightly from the product described herein.

Page #2 SKU:93216

For technical questions, please call 1-800-444-3353.

Page #2 SKU:93216

For technical questions, please call 1-800-444-3353.

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use tools in damp, wet, or poorly lit locations.

Don’t expose to rain. Keep work area well lit. Do not use electrically powered air

compressors in the presence of flammable gases or liquids.

3. Keep children away. Children must never be allowed in the work area. Do not let them

handle machines, tools, or hoses. Keep others a safe distance from tool while tool is in

operation as accidental actuation may occur, possibly causing injury.

4. Store idle equipment. When not in use, tools must be locked up in a dry location to

inhibit rust. Always lock up tools and keep out of reach of children.

5. Do not force the tool. It will do the job better and more safely at the rate for which it

was intended. Do not use inappropriate attachments in an attempt to exceed the tool’s

capacities.

Air Die Grinder

Free Speed 22000 RPM

Avg. Air Consumption 3 CFM

Recommended Air Pressure 90 PSI

Air Inlet 1/4" NPT

Collet size 1/4"

Impact Wrench

Anvil Size 1/2"

Avg. Air Consumption 4 CFM

Recommended Air Pressure 90 PSI

Air Inlet 1/4" NPT

Free Speed 7,000 RPM

Sockets size 1/2", 9/16", 5/8", 3/4"

Maximum Torque 230 ft-lbs.

SPECIFICATIONS

SAVE THIS MANUAL

You will need the manual for the safety warnings and cautions, assembly instructions, operating

procedures, maintenance procedures, trouble shooting, parts list, and diagram. Keep your

invoice with this manual. Write the invoice number on the inside of the front cover. Keep

both this manual and your invoice in a safe, dry place for future reference.

SAFETY WARNING & CAUTIONS

WARNING: When using pneumatic equipment, basic safety precautions should always be

followed to reduce the risk of personal injury and hazards due to over pressurization. READ ALL

INSTRUCTIONS BEFORE USING THIS TOOL!

Utility Torque 20-150 Ft.Lbs.

Page #3 SKU:93216

For technical questions, please call 1-800-444-3353.

6. Use the right tool for the job. Do not attempt to force a small tool or attachment to do

the work of a larger industrial tool. Do not use a tool for a purpose for which it was not

intended.

7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts.

Non-skid footwear is recommended. Wear restrictive hair covering to contain long hair.

8. Use eye and ear protection. Always wear ANSI-approved chemical splash goggles

when working with chemicals. Always wear ANSI-approved impact safety goggles at other

times. Wear a full face shield if you are producing metal filings or wood chips. Wear an

ANSI-approved dust mask or respirator when working around metal, wood, and chemical

dusts and mists. When operating for extended periods of time, use approved ear protection.

Safety goggles and ear protectors are available from Harbor Freight Tools.

9. Do not abuse the power cord. Do not yank compressor’s cord to disconnect it from the

receptacle. Do not carry tools by the cord.

10. Do not overreach. Keep proper footing and balance at all times. Do not reach over or

across running machines.

11. Maintain tools with care. Keep tools sharp and clean for better and safer performance.

Follow instructions for lubricating and changing accessories. Inspect compressor’s cord

periodically and, if damaged, have it repaired by an authorized technician. Inspect all

hoses for leaks prior to use. The handles must be kept clean, dry, and free from oil and

grease at all times.

12. Remove adjusting keys and wrenches. Make it a habit to check that keys and adjusting

wrenches are removed from the tool or machine work surface before plugging it in.

13. Avoid unintentional starting. Do not carry any tool with your finger on the trigger, whether

it is connected to the compressor or not.

14. Stay alert. Watch what you are doing; use common sense. Do not operate any tool when

you are tired.

15. Check damaged parts. Before using any tool, any part that appears damaged should

be carefully checked to determine that it will operate properly and perform its intended

function. Check for alignment and binding of moving parts; any broken parts or mounting

fixtures; and any other condition that may affect proper operation. Any part that is damaged

should be properly repaired or replaced by a qualified technician. Do not use the tool if any

switch does not turn on and off properly.

16. Replacement parts and accessories. When servicing, use only identical replacement

parts. Use of any other parts will void the warranty. Only use accessories intended for

use with this tool. Approved accessories are available from Harbor Freight Tools.

17. Do not operate tool if under the influence of alcohol or drugs. Read warning labels

on prescriptions to determine if your judgment or reflexes are impaired while

taking drugs. If there is any doubt, do not operate the tool.

Page #4 SKU:93216

For technical questions, please call 1-800-444-3353.

18. Drain compressor every day. Do not allow moisture to build up inside the compressor.

Do not allow compressor to sit pressurized for longer than one hour.

19. Make sure all equipment is rated to the appropriate capacity. Make sure that the

regulator is set at least 10 PSI lower than the lowest rated piece of equipment

you are using.

20. Do not use oxygen, combustible gases, or bottled gases as a power source.

The tool may explode, possibly causing injury.

21. Do not exceed the recommended air pressure of 90 PSI.

22. Tool must not hold pressure when air supply is disconnected. If a wrong fitting

is used, the tool can remain charged with air after disconnecting and thus will

be able to cycle after the air line is disconnected possibly causing injury.

23. Always disconnect air supply: Before making adjustments, when servicing the tool,

when clearing a jam, when tool is not in use, or when moving to a different work area,

as accidental actuation may occur, possibly causing injury.

24. Disconnect power. Unplug compressor when not in use.

25. Outdoor extensions cords. When the equipment is operated outdoors, use only extension

cords intended for outside use. See chart under “Extension Cords” for the proper

AWG rating depending on the length of the cord(s) being used.

26. Do not abuse the power cord. Do not yank it to disconnect it from the receptacle.

Do not carry tools by the cord.

27. Guard against electric shock. Prevent body contact with grounded surfaces such

as pipes, radiators, ranges, and refrigerator enclosures.

Page #5 SKU:93216

For technical questions, please call 1-800-444-3353.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area,

and work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles. (California Health & Safety Code §

25249.5,

et seq.

)

WARNING!Thewarnings,precautions,andinstructions discussedinthis manual

cannot cover all possible conditions and situations that may occur. The operator

must understand that common sense and caution are factors which cannot be built

into this product, but must be supplied by the operator.

SPECIFIC SAFETY RULES

1. Maintain labels and nameplates on the air tools. These carry important

information. If unreadable or missing, contact Harbor Freight Tools for a replacement.

2. Use clean, dry, regulated, compressed air at 90 PSI. Do not exceed the

recommended 90 PSI. Never use oxygen, carbon dioxide, combustible gases, or

any other bottled gas as a power source for this tool.

3. When connecting to the air supply: Prior to each use, if an automatic oiler is

not

used, add two drops of air tool oil into the inlet bushing of the Die Grinder / Impact

Wrench.

4. Use appr

5. For impact wrench, only use impact sockets.

opriate accessories only. ONLY use accessories with a 1/4” shank

long enough to fit securely into the collet and that are rated at 22,000 RPM or

greater. Other accessories may come loose, or break and fly apart causing severe

personal injury.

6. WARNING! Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities, contain chemicals known (to the State of California) to

cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are: lead from lead-based paints, crystalline silica from bricks and cement

or other masonry products, arsenic and chromium from chemically treated lumber.

Page #6 SKU:93216

For technical questions, please call 1-800-444-3353.

GROUNDING INSTRUCTIONS

If compressor has a three-prong plug

1. If the compressor has a three-prong plug, the third prong (round) is the ground. Plug the

machine’s cord only into three-prong receptacles. Never cut off the round prong. Cutting off

the ground will result in a safety hazard and void the warranty.

2. If a three-prong receptacle is not available, you may use an adapter. Extending from the male

end of the adapter, you will find a ring connector or wire lead with a ring connector where the

ground (round prong) would be. Remove the center screw of the outlet cover and put the

screw through the ring connector and back into the hole of the outlet cover. Do not over-

tighten or you will crack the outlet cover.

If compressor has a two-prong plug

If the compressor has a polarized plug, one prong is wider than the other prong. This plug will fit in

polarized outlet only one way. If the plug does not fit fully in the outlet reverse the plug. If it still

does not fit, contact a qualified electrician to install the proper outlet. Do not attempt to modify

the plug in any way. Modifying the plug will result in a safety hazard and void the warranty.

Page #7 SKU:93216

For technical questions, please call 1-800-444-3353.

UNPACKING for 93216 52 Pcs Air Tool Kit Impact Wrench / Die Grinder Set

Description Q'ty

1/2" Air Impact Wrench 1

1/4" Air Die Grinder 1

1/2"*1/2" Sanding Drum 1

3/4"*1" Sanding Drum 1

1/8" Shank Grinding Stone 5

1/4" Shank Grinding Stone 5

Spanner 2

Head Tire Chuck 1

1/8" Collet 1

Quick Connect Female Coupler 1

Ball Foot Tire Gauge 1

1/2" to 3" EXT.BAR 1

Blow Gun 1

4mm Allen Wrench 1

1/2" Impact Socket 1

9/16" Impact Socket 1

3/4" Impact Socket 1

5/8" Impact Sockets 1

Sport Needle 1

1/4" to 1/4" NPT Female Hose Connector 1

1/4" to 1/4" NPT Male Hose Connector 1

Rubber Nozzle 1

Tapered Nozzle 1

High Pressure Nozzle 1

Needle Adaptor 1

Safety Nozzle 1

Teflon Tape 1

Quick Connector 4

Air Tool Oil 1

1/2"*1/2" Sanding Roll 5

3/4"*1" Sanding Roll 5

Blow Mold Case 1

UNPACKING

When unpacking, check to make sure the following parts are included. All sizes listed below are

approximate. If any parts are missing or broken, please call Harbor Freight Tools at the number

on the cover of this manual.

Impact Wrench

This Impact Wrench develops a maximum of 230 ft/lbs. of torque. The amount of torque can be

increased or decreased using the AIR REGULATOR (12). When the Air Regulator is completely

screwed in it is at it’s lowest setting. Air pressure increases as you loosen the Air Regulator.

Page #8 SKU:93216

For technical questions, please call 1-800-444-3353.

Air

Tool

OPERATION

Setup

Frequent, but not excessive, lubrication is required for best performance. Oil added through the

airline connection will lubricate internal parts. An automatic airline oiler is recommended but oil

may be added manually before every operation or after about 1 hour of continuous use. Only a

few drops of oil at a time are necessary. Too much oil will collect inside the tool and be blown

out during the exhaust cycle. ONLY USE PNEUMATIC TOOL OIL. Do not use detergent oil or

additives as these lubricants will cause accelerated wear to the seals in the tool.

Dirt and water in the air supply are major causes of pneumatic tool wear. Use a filter/oiler for

better performance and longer life. The filter must have adequate flow capacity for the specific

application. Consult the manufacturer’s instructions for proper maintenance of your filter.

The connector on the tool must not hold pressure when the air supply is disconnected. If the

wrong fitting is used, the tool can remain charged with air after being disconnected and still be

able to drive a fastener. See Figure 1 for the recommended accessories and connection order.

Figure 1 — Airline Oiler Assembly

Page #9 SKU:93216

For technical questions, please call 1-800-444-3353.

Impact Wrench Operation

Step 1: Set the compressor’s pressure regulator to a maximum of 90 PSI. 90 PSI is satisfac-

tory without harming this tool.

Step 2: Remove the plastic cap from the rear of the HOSE ADAPTER (10).

Step 3: Wrap the threads of the Air Coupler with teflon tape. Attach the Air Coupler

to the HOSE ADAPTER. Tighten the fitting.

Step 4: Determine the socket size necessary for the job you need to do. Attach the appropriate

1/2” drive socket to the Impact Wrench as shown in Figure 7.

Figure 7 — Attaching the Air Coupler and Socket

Step 5: Connect the Impact Wrench to the air compressor’s hose. If leaking is detected,

disconnect the air hose and repair before use.

Page #10 SKU:93216

For technical questions, please call 1-800-444-3353.

Step 6: Select the power setting for Loosening by pushing in and turning the AIR REGULATOR

(12) located on the bottom of the Impact

Wrench as shown in Figure 8.

When the Air Regulator is completely

screwed in it is at it’s lowest setting.

Air pressure increases as you push in

and turn the Air Regulator.

Figure 8 — Adjusting the Reverse Power Setting

Step 7: Select the direction of the Wrench (forward or reverse) by pushing the REVERSE

VALVE (3) located on the handle of the Impact Wrench as shown in Figure 9.

Figure 9 — Selecting Reverse Direction

C AUTION

Use the Setting Appropriate for the

Job. Do Not Set the Power Setting

Higher Than Needed. Damage to

Parts Could Result.

(12)

(3)

Inhaltsverzeichnis

Andere Central Pneumatic Elektrowerkzeuge Handbücher

Central Pneumatic

Central Pneumatic Central Pneumatic 1/4" Stubby Air Ratchet... Bedienungsanleitung

Central Pneumatic

Central Pneumatic 46446 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 54700 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 54753 Stücklistenhandbuch

Central Pneumatic

Central Pneumatic Contractor 93197 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 68029 Installationshandbuch

Central Pneumatic

Central Pneumatic 167 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 92849 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 65706 Installationshandbuch

Central Pneumatic

Central Pneumatic 99792 Installationshandbuch

Central Pneumatic

Central Pneumatic 47214 Original Bedienungsanleitung

Central Pneumatic

Central Pneumatic 65902 Installationshandbuch

Central Pneumatic

Central Pneumatic 67996 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 47706 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 93048 Bedienungsanleitung

Central Pneumatic

Central Pneumatic Contractor 90399 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 95119 Installationshandbuch

Central Pneumatic

Central Pneumatic 98898 Installationshandbuch

Central Pneumatic

Central Pneumatic 95098 Bedienungsanleitung

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 68128 Installationshandbuch

Central Pneumatic

Central Pneumatic 68018 Installationshandbuch

Central Pneumatic

Central Pneumatic 36567 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 95801 Stücklistenhandbuch

Central Pneumatic

Central Pneumatic 68423 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch