Central Pneumatic 95119 Installationshandbuch

3/8” MINI PALM RATCHET

WRENCH

SET UP AND OPERATING INSTRUCTIONS

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

of this manual or any artwork contained herein may be reproduced in any

shape or form without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

Diagrams within this manual may not be drawn proportionally.

Due to continuing improvements, actual product may differ slightly from the product described herein.

Distributed exclusively by Harbor Freight Tools®.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Model

95119

Rev 07k

3/8” MINI PALM RATCHET WRENCH

SET UP AND OPERATING INSTRUCTIONS

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

of this manual or any artwork contained herein may be reproduced in any

shape or form without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

Diagrams within this manual may not be drawn proportionally.

Due to continuing improvements, actual product may differ slightly from the product described herein.

Distributed exclusively by Harbor Freight Tools ®.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Model

95119

Rev 07k

PRODUCT SPECIFICATIONS

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly, operat-

ing, inspection, maintenance and cleaning procedures, parts list and assembly diagram.

Keep your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep this manual and invoice in a safe and dry place for future reference.

GENERAL SAFETY RULES

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed in the following

pages may result in electric shock, re, and/or serious injury.

SAVE THESE INSTRUCTIONS

SKU 95119 For technical questions, please call 1-800-444-3353 PAGE 2

UNPACKING

When unpacking, check to make sure the product is intact and undamaged. If any parts

are missing or broken, please call Harbor Freight Tools at the number shown on the cover

of this manual as soon as possible.

Drive Size 3/8” Square Drive

Max. Working Pressure 90 PSI

Minimum Air Consumption Required 3.0 CFM @ 90 PSI

Free Speed RPM 250 Max. RPM

Torque 20 ft./lb.

Air Inlet Size 1/4” - 18 NPT

Required Air Hose I.D. 3/8”

Exhaust Type Rear Exhaust

Overall Dimensions 5-5/16” L x 1-5/16” W x 1-11/16” H

Bolt Capacity 1/2”

Unit Weight 1.3 lb.

3. Keep bystanders, children, and visitors away while operating a pneumatic

tool. Distractions can cause you to lose control. Protect others in the work area

from debris such as chips and sparks. Provide barriers or shields as needed.

PERSONAL SAFETY

1. Stay alert. Watch what you are doing, and use common sense when

operating a pneumatic tool. Do not use a pneumatic tool while tired or

under the inuence of drugs, alcohol, or medication. A moment of

inattention while operating pneumatic tools may result in serious personal injury.

2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose

clothes, jewelry, or long hair can be caught in moving parts.

3. Avoid accidental starting. Be sure the Throttle Lever (11) is off before

connecting to the air supply. Carrying pneumatic tools with your nger on the

Throttle Lever, or connecting pneumatic tools to the air supply with the Throttle

Lever on, invites accidents.

4. Remove adjusting keys or wrenches before turning on the tool. A wrench

or a key that is left attached to a rotating part of the tool may result in personal

injury.

5. Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the tool in unexpected situations.

6. Use safety equipment. Always wear ANSI approved safety impact eye

goggles, hearing protection, and heavy duty work gloves.

TOOL USE AND CARE

1. Use clamps or other practical ways to secure and support the workpiece to

a stable platform. Holding the work by hand is unstable and may lead to loss of

control. Only work on a workpiece that is properly secured.

2. Do not operate pneumatic tools in explosive atmospheres, such as in the

presence of ammable liquids, gases, or dust. Pneumatic tools create sparks

which may ignite ammables.

1. Keep your work area clean and well lit. Cluttered benches and dark areas

invite accidents.

WORK AREA

SKU 95119 For technical questions, please call 1-800-444-3353 PAGE 3

2. Do not force the tool. Use the correct tool for your application. The correct

tool will do the job better and safer at the rate for which it is designed.

3. Do not use the power tool if the Throttle Lever does not turn it on or off.

Any tool that cannot be controlled with the Throttle Lever is dangerous and must

be replaced.

4. Disconnect the air hose from the tool before making any adjustments,

changing accessories, or storing the tool. Such preventive safety measures

reduce the risk of starting the tool accidentally.

5. Store idle tools out of reach of children and other untrained persons. Tools

are dangerous in the hands of untrained users.

6. Maintain tools with care. Do not use a damaged tool. Tag damaged tools “Do

not use” until repaired.

7. Check for misalignment or binding of moving parts, breakage of parts,

and any other condition that may affect the tool’s operation. If damaged,

have the tool serviced before using. Many accidents are caused by poorly

maintained tools.

8. Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool may become hazardous

when used on another tool.

SERVICE

1. Tool service must be performed only by qualied repair personnel. Service

or maintenance performed by unqualied personnel could result in a risk of injury.

2. When servicing a tool, use only identical replacement parts. Follow

instructions in the “Inspection, Maintenance, And Cleaning” section of this

manual. Use of unauthorized parts or failure to follow maintenance instructions

may create a risk of injury.

SKU 95119 For technical questions, please call 1-800-444-3353 PAGE 4

SPECIFIC SAFETY RULES

1. Maintain labels and nameplates on the Ratchet Wrench. These carry

important information. If unreadable or missing, contact Harbor Freight Tools for

a replacement.

2. CAUTION! To avoid injury, grip the Ratchet Wrench rmly with both hands.

SKU 95119 For technical questions, please call 1-800-444-3353 PAGE 5

3. Use clean, dry, regulated, compressed air at 90 PSI. Do not exceed the

recommended 90 PSI. Never use oxygen, carbon dioxide, combustible gases, or

any other bottled gas as a power source for this tool.

4. When connecting to the air supply: Prior to each use, if an automatic oiler is

not used, add two drops of air tool oil (not included) into the Air Inlet (10) tting of

the Ratchet Wrench.

5. Always disconnect the Ratchet Wrench from its compressed air supply

source, and squeeze the Throttle Lever (11) to release all compressed air in

the tool before performing any maintenance or services.

6. Industrial applications must follow OSHA requirements.

7. WARNING! The brass components of this product contain lead, a

chemical known to the State of California to cause birth defects (or other

reproductive harm). (California Health & Safety code 25249.5, et seq.)

8. WARNING! The warnings, precautions, and instructions discussed in this

manual cannot cover all possible conditions and situations that may occur. The

operator must understand that common sense and caution are factors which can-

not be built into this product, but must be supplied by the operator.

ASSEMBLY AND OPERATING INSTRUCTIONS

NOTE:

For additional references to the parts listed in the

following pages, refer to the Assembly Diagram on page 9.

To Attach A Quick Connector:

1. Prior to use, the Ratchet Wrench requires the attachment of a Quick Connector

(not included) into its Air Inlet (10). To do so, wrap approximately 3” of pipe

thread sealer tape (not included) around the male threads of a Quick Connector.

Then, rmly tighten the Quick Connector into the Air Inlet. (See Figure A.)

QUICK CONNECTOR

(NOT INCLUDED)

FIGURE A

AIR INLET (10)

3/8” MINI PALM RATCHET WRENCH

SET UP AND OPERATING INSTRUCTIONS

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

2007 by Harbor Freight Tools

of this manual or any artwork contained herein may be reproduced in any

shape or form without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

Diagrams within this manual may not be drawn proportionally.

Due to continuing improvements, actual product may differ slightly from the product described herein.

Distributed exclusively by Harbor Freight Tools ®.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Model

95119

Rev 07k

Recommended Compressed Air System Set-Up:

1. For best service, you should incorporate an oiler, regulator, and inline lter when

using an air compressor (not included) to operate the Ratchet Wrench.

(See Figure B.)

SKU 95119 For technical questions, please call 1-800-444-3353 PAGE 6

FIGURE B

RECOMMENDED COMPRESSED AIR SYSTEM SET-UP

ATTACH

QUICK CONNECTOR

TO RATCHET WRENCH

To Operate The Ratchet Wrench:

2. After installing a socket onto the Drive Head of the Ratchet Wrench, set the

Forward/Reverse Knob (33) to the direction in which you wish the Ratchet to

turn (Forward = clockwise rotation / Reverse = counterclockwise rotation).

(See Figure C.)

3. Connect the air supply hose to the Ratchet Wrench. Turn on the air compressor,

and set its regulator to the recommended 90 PSI for the Ratchet Wrench.

4. Insert the socket onto the bolt or nut that is to be loosened/tightened.

5. Make sure to hold the Ratchet Wrench rmly with both hands, as torque will

cause the tool to twist. Then gently squeeze the Throttle Lever (11) to tighten

or loosen the bolt/nut. Apply additional pressure on the Throttle Lever (11) as

needed. (See Figure C.)

1. The Ratchet Wrench is designed to work with all 3/8” drive sockets (not

included). Before installing a socket, make sure your hand is away from the

Throttle Lever (11). When installing a socket onto the Drive Head of

the Ratchet Wrench, always make sure the socket is rmly secured

in the Drive Head.

(See Figure C, next page.)

SKU 95119 For technical questions, please call 1-800-444-3353 PAGE 7

6. If necessary, use a torque wrench (not included) to verify the desired torque of

a bolt/nut. If a bolt/nut requires a higher torque level than that produced by the

Ratchet Wrench at 90 PSI, an alternate means (other than the Ratchet Wrench)

of achieving the desired torque should be used.

7. When nished, release the Throttle Lever (11) to stop the Ratchet Wrench.

(See Figure C.)

8. Turn off the air compressor. Disconnect the Ratchet Wrench from its air supply

hose, and remove the socket from the tool.

9. Make sure to store the Ratchet Wrench in a dry, clean, location out of reach of

children and other unauthorized users.

THROTTLE

LEVER

(11)

INSPECTION, MAINTENANCE, AND CLEANING

1. WARNING! Always make sure the Throttle Lever (11) is in its “OFF”

position, and disconnect the Ratchet Wrench from its compressed air supply

before performing any inspection, adjustments, maintenance, or cleaning.

2. Before each use, inspect the general condition of the Ratchet Wrench. Check

for loose screws, misalignment or binding of moving parts, cracked or broken

parts, damaged air hoses, and any other condition that may affect its safe

operation. If abnormal noise or vibration occurs, have the problem corrected

before further use. Do not use damaged equipment.

FORWARD/REVERSE

KNOB (33)

FIGURE C

AIR

VALVE

CAP (8)

3/8” DRIVE HEAD

SKU 95119 For technical questions, please call 1-800-444-3353 PAGE 7

6. If necessary, use a torque wrench (not included) to verify the desired torque of

a bolt/nut. If a bolt/nut requires a higher torque level than that produced by the

Ratchet Wrench at 90 PSI, an alternate means (other than the Ratchet Wrench)

of achieving the desired torque should be used.

7. When ﬁnished, release the Throttle Lever (11) to stop the Ratchet Wrench.

(See Figure C.)

8. Turn off the air compressor. Disconnect the Ratchet Wrench from its air supply

hose, and remove the socket from the tool.

9. Make sure to store the Ratchet Wrench in a dry, clean, location out of reach of

children and other unauthorized users.

THROTTLE

LEVER

(11)

INSPECTION, MAINTENANCE, AND CLEANING

1. WARNING! Always make sure the Throttle Lever (11) is in its “OFF”

position, and disconnect the Ratchet Wrench from its compressed air supply

before performing any inspection, adjustments, maintenance, or cleaning.

2. Before each use, inspect the general condition of the Ratchet Wrench. Check

for loose screws, misalignment or binding of moving parts, cracked or broken

parts, damaged air hoses, and any other condition that may affect its safe

operation. If abnormal noise or vibration occurs, have the problem corrected

before further use. Do not use damaged equipment.

FORWARD/REVERSE

KNOB (33)

FIGURE C

AIR

VALVE

CAP (8)

3/8” DRIVE HEAD

4. CAUTION! All maintenance, service, or repairs not listed in this manual are

only to be attempted by a qualied service technician.

SKU 95119 For technical questions, please call 1-800-444-3353 PAGE 8

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN

THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY

REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY

REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.

IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS

REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE

BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION

OF REPLACEMENT PARTS THERETO.

PARTS LIST

3. Daily: With a soft brush, cloth, or vacuum, remove all dust and debris from

the Ratchet Wrench. Then, use a premium quality, lightweight machine oil to

lubricate all external moving parts.

Part # Description

1 Motor Housing

2 Valve Bushing

3 O Ring

4 O Ring

5 Throttle Valve

6 Spring

7 O Ring

8 Air Valve Cap

9 Exhaust Sleeve

10 Air Inlet

11 Throttle Lever

12 Bearing

13 Rear End Plate

14 Pin

15 Pin

16 Cylinder

17 Rotor

18 Rotor Blade

19 Front End Plate

20 Roll Pin

21 Bearing

22 Planet Gear

Part # Description

23 Planet Pin

24 Gear Cage

25 Internal Gear

26 Clamp Nut

27 Ratchet Housing

28 Bushing

29 Drive Bushing

30 Ratchet Yoke

31 Washer

32 Pin

33 Forward/Reverse Knob

34 Reverse Spring

35 Reverse Pin

36 3/8” Ratchet Anvil

37 Ratchet Pawl

38 Pin

39 Spring

40 Ball

41 Thrust Washer

42 Retaining Ring

SKU 95119 For technical questions, please call 1-800-444-3353 PAGE 9

NOTE:

Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

ASSEMBLY DIAGRAM

SKU 95119 For technical questions, please call 1-800-444-3353 PAGE 9

NOTE:

Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

ASSEMBLY DIAGRAM

90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality

and durability standards, and warrants to the original purchaser that this product is free

from defects in materials and workmanship for the period of 90 days from the date of

purchase. This warranty does not apply to damage due directly or indirectly, to misuse,

abuse, negligence or accidents, repairs or alterations outside our facilities, criminal ac-

tivity, improper installation, normal wear and tear, or to lack of maintenance. We shall in

no event be liable for death, injuries to persons or property, or for incidental, contingent,

special or consequential damages arising from the use of our product. Some states

do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY

IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE

WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with

transportation charges prepaid. Proof of purchase date and an explanation of the com-

plaint must accompany the merchandise. If our inspection veries the defect, we will ei-

ther repair or replace the product at our election or we may elect to refund the purchase

price if we cannot readily and quickly provide you with a replacement. We will return re-

paired products at our expense, but if we determine there is no defect, or that the defect

resulted from causes not within the scope of our warranty, then you must bear the cost

of returning the product.

This warranty gives you specic legal rights and you may also have other rights which

vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

Inhaltsverzeichnis

Andere Central Pneumatic Elektrowerkzeuge Handbücher

Central Pneumatic

Central Pneumatic 98898 Installationshandbuch

Central Pneumatic

Central Pneumatic 68029 Installationshandbuch

Central Pneumatic

Central Pneumatic 65902 Installationshandbuch

Central Pneumatic

Central Pneumatic 95098 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 92849 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 65706 Installationshandbuch

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 68128 Installationshandbuch

Central Pneumatic

Central Pneumatic 66984 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 95801 Stücklistenhandbuch

Central Pneumatic

Central Pneumatic 36567 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 54753 Stücklistenhandbuch

Central Pneumatic

Central Pneumatic 66874 Installationshandbuch

Central Pneumatic

Central Pneumatic 96661 Montageanleitung

Central Pneumatic

Central Pneumatic Contractor 46365 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 167 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 46446 Bedienungsanleitung

Central Pneumatic

Central Pneumatic Central Pneumatic 1/4" Stubby Air Ratchet... Bedienungsanleitung

Central Pneumatic

Central Pneumatic 66886 Installationshandbuch

Central Pneumatic

Central Pneumatic 68018 Installationshandbuch

Central Pneumatic

Central Pneumatic 47706 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 54700 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 68426 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 94802 Bedienungsanleitung

Central Pneumatic

Central Pneumatic Contractor 93197 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch