Chamberlain ELITE CSL24V Bedienungsanleitung

This model is for use on vehicular

passage gates ONLY and not

intended for use on pedestrian

passage gates.

This model is intended for use in

Class I, II, III and IV vehicular slide

gate applications.

UL325

compliant

UL991

compliant

CSL24V™& CSL24VH™

VEHICULAR SLIDE GATE OPERATOR

INSTALLATION MANUAL

THIS PRODUCT IS TO BE

INSTALLED AND SERVICED BY

A TRAINED GATE SYSTEMS

TECHNICIAN ONLY.

Visit www.liftmaster.com to

locate a professional installing

dealer in your area.

Your model may look different than the model illustrated in this manual.

When you see these Safety Symbols and Signal Words on the following pages, they

will alert you to the possibility of serious injury or death if you do not comply with

the warnings that accompany them. The hazard may come from something

mechanical or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following pages, it will alert you to the

possibility of damage to your gate and/or the gate operator if you do not comply

with the cautionary statements that accompany it. Read them carefully.

IMPORTANT NOTE

• BEFORE attempting to install, operate or maintain the operator, you must read

and fully understand this manual and follow all safety instructions.

• DO NOT attempt repair or service of your gate operator unless you are an

Authorized Service Technician.

MECHANICAL

ELECTRICAL

SAFETY SYMBOL AND SIGNAL WORD REVIEW

SAFETY

TABLE OF CONTENTS

SAFETY 1

UL325 MODEL CLASSIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY INSTALLATION INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

GATE CONSTRUCTION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

REQUIRED ENTRAPMENT PROTECTION DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

IMPORTANT SAFETY INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

IMPORTANT SAFETY INFORMATION CONTINUED.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

INTRODUCTION 8

OPERATOR SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

CARTON INVENTORY & OPERATOR DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

PREPARATION 10

SITE PREPARATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

INSTALLATION 12

DETERMINE LOCATION FOR CONCRETE PAD AND OPERATOR . . . . . . . . . . . . . . . . . . . . . . 12

CONCRETE PAD AND OPERATOR ATTACHMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

STANDARD INSTALLATION ONLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

REAR INSTALLATION ONLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

WIRING 14

WIRE THE ENTRAPMENT PROTECTION DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

EARTH GROUND ROD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

POWER WIRING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

POWER WIRING CONTINUED.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

AC POWER SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

CONNECT BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

CONNECT BATTERIES CONTINUED... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

DUAL GATES ONLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

DUAL GATES ONLY CONTINUED.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

ADJUSTMENT 21

LIMIT AND FORCE ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

OBSTRUCTION TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

PROGRAMMING 23

REMOTE CONTROLS (NOT PROVIDED). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

ERASE ALL CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

FINISH INSTALLATION 24

INSTALL THE COVER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

OPERATION 25

RESET SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

MANUAL DISCONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

OPERATOR ALARM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

HEATER (IF APPLICABLE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

ADDITIONAL FEATURES 26

CONTROL BOARD OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

WIRING ACCESSORIES TO THE CONTROL BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

EXPANSION BOARD OVERVIEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

WIRING ACCESSORIES TO THE EXPANSION BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

SAMS WIRING WITH RELAYS NOT ENERGIZED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

DUAL GATE SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

GATE OPERATOR SETUP EXAMPLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

LIMIT SETUP WITH A REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

LIFTMASTER INTERNET GATEWAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

TROUBLESHOOTING 34

CONTROL BOARD LEDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

CONTROL BOARD LEDS CONTINUED.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

TROUBLESHOOTING CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

WIRING DIAGRAM 39

REPAIR PARTS 40

INDIVIDUAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

ACCESSORIES 42

MAINTENANCE 44

MAINTENANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

BATTERIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

DRIVE CHAIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

WARRANTY 45

CLASS I – RESIDENTIAL VEHICULAR GATE OPERATOR

A vehicular gate operator (or system) intended for use in a home of one-to four

single family dwellings, or a garage or parking area associated therewith.

CLASS II – COMMERCIAL/GENERAL ACCESS VEHICULAR

GATE OPERATOR

A vehicular gate operator (or system) intended for use in a commercial location or

building such as a multi-family housing unit (five or more single family units) hotel,

garage, retail store or other building servicing the general public.

CLASS III – INDUSTRIAL/LIMITED ACCESS VEHICULAR

GATE OPERATOR

A vehicular gate operator (or system) intended for use in a industrial location or

building such as a factory or loading dock area or other location not intended to

service the general public.

CLASS IV– RESTRICTED ACCESS VEHICULAR GATE

OPERATOR

A vehicular gate operator (or system) intended for use in a guarded industrial

location or building such as an airport security area or other restricted access

locations not servicing the general public, in which unauthorized access is prevented

via supervision by security personnel.

UL325 ENTRAPMENT PROTECTION REQUIREMENTS

This chart illustrates the entrapment protection requirements for the UL325 classes.

NOTE: UL requires that all installations must have warning signs placed in plain

view on both sides of the gate to warn pedestrians of the dangers of motorized gate

systems.

III

In order to complete a proper installation you must satisfy the entrapment

protection chart shown. That means that the installation must have one primary

means of entrapment protection and one independent secondary means of

entrapment protection. Both primary and secondary entrapment protection

methods must be designed, arranged or configured to protect against

entrapments in both the open and close directions of gate travel.

For Example: For a gate system that is installed on a single-family residence

(UL325 Class I) you must provide the following: As your primary type of

entrapment protection you must provide

• Type A - Inherent (built into the operator) entrapment sensing and at

least one of the following as your secondary entrapment

protection:

• Type B1 - Non-contact sensors such as photoelectric sensors,

• Type B2 - Contact sensors such as gate edges

UL325 MODEL CLASSIFICATIONS

SAFETY

UL325 MODEL CLASSIFICATIONS

GATE OPERATOR ENTRAPMENT PROTECTION

UL325 Classification Slide Gate Operator

Primary Type Secondary Type

CLASS I-CLASS IV A B1 or B2

1. Vehicular gate systems provide convenience and security. Gate systems are

comprised of many component parts. The gate operator is only one

component. Each gate system is specifically designed for an individual

application.

2. Gate operating system designers, installers and users must take into account

the possible hazards associated with each individual application. Improperly

designed, installed or maintained systems can create risks for the user as

well as the bystander. Gate systems design and installation must reduce

public exposure to potential hazards.

3. A gate operator can create high levels of force in its function as a component

part of a gate system. Therefore, safety features must be incorporated into

every design. Specific safety features include:

• Gate Edges • Guards for Exposed Rollers

• Photoelectric Sensors • Screen Mesh

• Vertical Posts • Instructional and Precautionary Signage

4. Install the gate operator only when:

a. The operator is appropriate for the construction and the usage class of the

gate.

b. All openings of a horizontal slide gate are guarded or screened from the

bottom of the gate to a minimum of 4 feet (1.2 m) above the ground to

prevent a 2-1/4 inches (6 cm) diameter sphere from passing through the

openings anywhere in the gate, and in that portion of the adjacent fence

that the gate covers in the open position.

c. All exposed pinch points are eliminated or guarded, and guarding is

supplied for exposed rollers.

5. The operator is intended for installation only on gates used for vehicles.

Pedestrians must be supplied with a separate access opening. The pedestrian

access opening shall be designed to promote pedestrian usage. Locate the

gate such that persons will not come in contact with the vehicular gate during

the entire path of travel of the vehicular gate.

6. The gate must be installed in a location so that enough clearance is supplied

between the gate and adjacent structures when opening and closing to reduce

the risk of entrapment. Swinging gates shall not open into public access

areas.

7. The gate must be properly installed and work freely in both directions prior

to the installation of the gate operator.

8. Controls intended for user activation must be located at least 6 feet (1.8 m)

away from any moving part of the gate and where the user is prevented

from reaching over, under, around or through the gate to operate the

controls. Outdoor or easily accessible controls shall have a security feature to

prevent unauthorized use.

9. The Stop and/or Reset (if provided separately) must be located in the

line-of-sight of the gate. Activation of the reset control shall not cause the

operator to start.

10.A minimum of two (2) WARNING SIGNS shall be installed, one on each side

of the gate where easily visible.

11.For a gate operator utilizing a non-contact sensor:

a. Reference owner’s manual regarding placement of non-contact sensor for

each type of application.

b. Care shall be exercised to reduce the risk of nuisance tripping, such as

when a vehicle trips the sensor while the gate is still moving.

c. One or more non-contact sensors shall be located where the risk of

entrapment or obstruction exists, such as the perimeter reachable by a

moving gate or barrier.

12.For a gate operator utilizing a contact sensor such as an edge sensor:

a. One or more contact sensors shall be located where the risk of

entrapment or obstruction exists, such as at the leading edge, trailing

edge and post mounted both inside and outside of a vehicular horizontal

slide gate.

b. One or more contact sensors shall be located at the bottom edge of a

vehicular vertical lift gate.

c. A hard wired contact sensor shall be located and its wiring arranged so

the communication between the sensor and the gate operator is not

subject to mechanical damage.

d. A wireless contact sensor such as the one that transmits radio frequency

(RF) signals to the gate operator for entrapment protection functions shall

be located where the transmission of the signals are not obstructed or

impeded by building structures, natural landscaping or similar obstruction.

A wireless contact sensor shall function under the intended end-use

conditions.

e. One or more contact sensors shall be located on the inside and outside

leading edge of a swing gate. Additionally, if the bottom edge of a swing

gate is greater than 6 inches (152 mm) above the ground at any point in

its arc of travel, one or more contact sensors shall be located on the

bottom edge.

f. One or more contact sensors shall be located at the bottom edge of a

vertical barrier (arm).

SAFETY INSTALLATION INFORMATION

SAFETY

SAFETY INSTALLATION INFORMATION

1. GENERAL REQUIREMENTS

1.1 Gates shall be constructed in accordance with the provisions given for the

appropriate gate type listed, refer to ASTM F2200 for additional gate types.

1.2 Gates shall be designed, constructed and installed to not fall over more than

45 degrees from the vertical plane, when a gate is detached from the

supporting hardware.

1.3 Gates shall have smooth bottom edges, with vertical bottom edged

protrusions not exceeding 0.50 inches (12.7 mm) when other than the

exceptions listed in ASTM F2200.

1.4 The minimum height for barbed tape shall not be less than 8 feet (2.44 m)

above grade and for barbed wire shall not be less than 6 feet (1.83 m)

above grade.

1.5 An existing gate latch shall be disabled when a manually operated gate is

retrofitted with a powered gate operator.

1.6 A gate latch shall not be installed on an automatically operated gate.

1.7 Protrusions shall not be permitted on any gate, refer to ASTM F2200 for

Exceptions.

1.8 Gates shall be designed, constructed and installed such that their movement

shall not be initiated by gravity when an automatic operator is disconnected.

1.9 A pedestrian gate shall not be incorporated into a vehicular gate panel or

that portion of the adjacent fence that the gate covers in the open position.

2. SPECIFIC APPLICATIONS

2.1 Any non-automated gate that is to be automated shall be upgraded to

conform to the provisions of this specification.

2.2 This specification shall not apply to gates generally used for pedestrian

access and to vehicular gates not to be automated.

2.3 Any existing automated gate, when the operator requires replacement, shall

be upgraded to conform to the provisions of this specification in effect at

that time.

3. VEHICULAR HORIZONTAL SLIDE GATES

3.1 The following provisions shall apply to Class I, Class II and Class III vehicular

horizontal slide gates:

3.1.1 All weight bearing exposed rollers 8 feet (2.44 m), or less, above grade

shall be guarded or covered.

3.1.2 All openings located between 48 inches (1.22 m) and 72 inches (1.83 m)

above grade shall be designed, guarded or screened to prevent a 4 inch

(102 mm) diameter sphere from passing through the openings anywhere in

the gate, and in that portion of the adjacent fence that covers in the open

position.

4. VEHICULAR HORIZONTAL SWING GATES

4.1 The following provisions shall apply to Class 1, Class II and Class III vehicular

horizontal swing gates:

4.1.1 Gates shall be designed, constructed and installed so as not to create an

entrapment area between the gate and the supporting structure or other

fixed object when the gate moves toward the fully open position, subject to

the provisions in the 4.1.1.1 and 4.1.1.2.

4.1.1.1 The width of an object (such as a wall, pillar or column) covered by a swing

gate when in the open position shall not exceed 4 inches (102 mm),

measured from the center line of the pivot point of the gate, refer to ASTM

F2200 for exception.

4.1.1.2 Except for the zone specified in Section 4.1.1.1, the distance between a

fixed object such as a wall, pillar or column, and a swing gate when in the

open position shall not be less than 16 inches (406 mm), refer to ASTM

F2200 for exception.

4.2 Class IV vehicular horizontal swing gates shall be designed, constructed and

installed in accordance with security related parameters specific to the

application in question.

GATE CONSTRUCTION INFORMATION

SAFETY

GATE CONSTRUCTION INFORMATION

Vehicular gates should be installed in accordance with ASTM F2200: Standard Specification for Automated Vehicular Gate Construction. For a copy, contact ASTM directly at

610-832-9585 or www.astm.org.

3.1.3 A gap, measured in the horizontal plane parallel to the roadway, between a

fixed stationary object nearest the roadway, (such as a gate support post)

and the gate frame when the gate is in either the fully open position or the

fully closed position, shall not exceed 2 1/4 inches (57 mm), refer to ASTM

F2200 for Exception.

3.1.4 Positive stops shall be required to limit travel to the designed fully open and

fully closed positions. These stops shall be installed at either the top of the

gate, or at the bottom of the gate where such stops shall horizontally or

vertically project no more than is required to perform their intended

function.

3.1.5 All gates shall be designed with sufficient lateral stability to assure that the

gate will enter a receiver guide, refer to ASTM F2200 for panel types.

3.2 The following provisions shall apply to Class IV vehicular horizontal slide

gates:

3.2.1 All weight bearing exposed rollers 8 feet (2.44 m), or less, above grade

shall be guarded or covered.

3.2.2 Positive stops shall be required to limit travel to the designed fully open and

fully closed positions. These stops shall be installed at either the top of the

gate, or at the bottom of the gate where such stops shall horizontally or

vertically project no more than is required to perform their intended

function.

Inside

Property

Inside

Property

To prevent SERIOUS INJURY or DEATH from a moving gate:

• Entrapment protection devices MUST be installed to protect anyone who may

come near a moving gate.

• Locate entrapment protection devices to protect in BOTH the open and close

gate cycles.

• Locate entrapment protection devices to protect between moving gate and

RIGID objects, such as posts or walls.

NON-CONTACT SENSORS

If the photoelectric sensor beam gets blocked while the gate is moving, the gate will stop and reverse. The gate will not be able to travel in that direction until the obstruction

is cleared. It is best to use monitored photoelectric sensors, model CPS-UN4. If a monitored photoelectric sensor is not working or loses power or the beam is blocked, then ALL

gate operation in that direction will stop. Unmonitored photoelectric sensor models AOMRON and RETROAB are also acceptable.

CONTACT SENSORS (EDGE SENSORS)

If the electrically activated edge sensor comes in contact with an obstruction while the gate is moving, the gate will stop and reverse. The gate will not be able to travel in that

direction until the obstruction is cleared. Use edge sensor models G65MG0204, G65MGR020, or G65MGS020.

REQUIRED ENTRAPMENT PROTECTION DEVICES

SAFETY

REQUIRED ENTRAPMENT PROTECTION DEVICES

An entrapment zone is every location or point of contact where a person can become entrapped between a moving gate and a stationary object. All gate operator systems

REQUIRE two independent entrapment protection systems for each entrapment zone. This operator contains an inherent (internal) entrapment protection system (the primary

entrapment protection system) and REQUIRES the addition of an external entrapment protection system (non-contact photoelectric sensor or contact safety edge sensor) for

EACH entrapment zone.

Your application may contain one or many entrapment zones. Property owners are obligated to test entrapment protection devices monthly.

Inside

Property

Outside

Property

Outside

Property

Inside

Property

Safety Non-Contact Sensor

Sensor for Open Cycle

Sensor for Close Cycle

Edge Sensor for Open Cycle

Edge Sensor for Open Cycle Edge Sensor for Close Cycle

Edge Sensor for Close Cycle

INSTALLATION

To prevent SERIOUS INJURY or DEATH from a moving gate:

• Pinch points must be guarded at all times. Install enclosed-style gate tracks and

roller guards.

• Place screen mesh 4 feet (1.2 m) high on the gate to prevent access through

openings anywhere the gate may travel.

• Mount controls at least 6 feet (1.8 m) from the gate or ANY moving part of the

gate.

• Install Warning signs on EACH side of gate in PLAIN VIEW. Permanently secure

each Warning sign in a suitable manner using fastening holes.

• This operator is intended for vehicular use only. To prevent INJURY to

pedestrians, a separate pedestrian access should be supplied, visible from the

gate. Locate the pedestrian access where there is not a chance of INJURY at any

point during full movement of the gate.

• Contact sensors MUST be located at the leading and trailing edges, and post

mounted both inside and outside a horizontal slide gate. Non-contact sensors

such as photo eyes MUST be mounted across the gate opening and operate

during BOTH the open and close cycles.

• Entrapment protection devices MUST be installed to protect anyone who may

come near a moving gate.

• Locate entrapment protection devices to protect in BOTH the open and close

gate cycles.

• Locate entrapment protection devices to protect between moving gate and RIGID

objects, such as posts or walls.

• Too much force on gate will interfere with proper operation of safety reversal

system.

• NEVER increase force beyond minimum amount required to move gate.

• NEVER use force adjustments to compensate for a binding or sticking gate.

• If one control (force or travel limits) is adjusted, the other control may also

need adjustment.

• After ANY adjustments are made, the safety reversal system MUST be tested.

Gate MUST reverse on contact with a rigid object.

• DO NOT touch the heater when switch is on, heater may be hot.

• To AVOID damaging gas, power or other underground utility lines, contact

underground utility locating companies BEFORE digging more than 18 inches

(46 cm) deep.

• ALWAYS wear protective gloves and eye protection when changing the battery

or working around the battery compartment.

To reduce the risk of SEVERE INJURY or DEATH:

• ANY maintenance to the operator or in the area near the operator MUST NOT

be performed until disconnecting the electrical power (AC or solar and battery)

and locking-out the power via the operator power switch. Upon completion of

maintenance the area MUST be cleared and secured, at that time the unit may

be returned to service.

• Disconnect power at the fuse box BEFORE proceeding. Operator MUST be

properly grounded and connected in accordance with national and local

electrical codes. NOTE: The operator should be on a separate fused line of

adequate capacity.

• ALL electrical connections MUST be made by a qualified individual.

• DO NOT install ANY wiring or attempt to run the operator without consulting the

wiring diagram. We recommend that you install an edge sensor BEFORE

proceeding with the control station installation.

• ALL power wiring should be on a dedicated circuit and well protected. The

location of the power disconnect should be visible and clearly labeled.

• ALL power and control wiring MUST be run in separate conduit.

WIRING

To reduce the risk of SEVERE INJURY or DEATH:

• Without a properly installed safety reversal system, persons (particularly small

children) could be SERIOUSLY INJURED or KILLED by a moving gate.

• Too much force on gate will interfere with proper operation of safety reversal

system.

• NEVER increase force beyond minimum amount required to move gate.

• NEVER use force adjustments to compensate for a binding or sticking gate.

• If one control (force or travel limits) is adjusted, the other control may also

need adjustment.

• After ANY adjustments are made, the safety reversal system MUST be tested.

Gate MUST reverse on contact with a rigid object.

ADJUSTMENT

IMPORTANT SAFETY INFORMATION

SAFETY

IMPORTANT SAFETY INFORMATION

To prevent SERIOUS INJURY or DEATH from a moving gate:

• Entrapment protection devices MUST be installed to protect anyone who may

come near a moving gate.

• Locate entrapment protection devices to protect in BOTH the open and close

gate cycles.

• Locate entrapment protection devices to protect between moving gate and RIGID

objects, such as posts or walls.

ADDITIONAL FEATURES

To reduce the risk of SEVERE INJURY or DEATH:

• READ AND FOLLOW ALL INSTRUCTIONS.

• ANY maintenance to the operator or in the area near the operator MUST NOT

be performed until disconnecting the electrical power (AC or solar and battery)

and locking-out the power via the operator power switch. Upon completion of

maintenance the area MUST be cleared and secured, at that time the unit may

be returned to service.

• Disconnect power at the fuse box BEFORE proceeding. Operator MUST be

properly grounded and connected in accordance with national and local

electrical codes. NOTE: The operator should be on a separate fused line of

adequate capacity.

• NEVER let children operate or play with gate controls. Keep the remote control

away from children.

• ALWAYS keep people and objects away from the gate. NO ONE SHOULD CROSS

THE PATH OF THE MOVING GATE.

• The entrance is for vehicles ONLY. Pedestrians MUST use separate entrance.

• Test the gate operator monthly. The gate MUST reverse on contact with a rigid

object or reverse when an object activates the non-contact sensors. After

adjusting the force or the limit of travel, retest the gate operator. Failure to

adjust and retest the gate operator properly can increase the risk of INJURY or

DEATH.

• Use the manual disconnect release ONLY when the gate is not moving.

• KEEP GATES PROPERLY MAINTAINED. Read the owner’s manual. Have a

qualified service person make repairs to gate hardware.

• ALL maintenance MUST be performed by a LiftMaster professional.

• Activate gate ONLY when it can be seen clearly, is properly adjusted and there

are no obstructions to gate travel.

• To reduce the risk of FIRE or INJURY to persons use ONLY LiftMaster part

29-NP712 for replacement batteries.

• SAVE THESE INSTRUCTIONS.

MAINTENANCE AND OPERATION

To protect against fire and electrocution:

• DISCONNECT power (AC or solar and battery) BEFORE installing or servicing

operator.

For continued protection against fire:

• Replace ONLY with fuse of same type and rating.

TROUBLESHOOTING

• ALWAYS wear protective gloves and eye protection when changing the battery

or working around the battery compartment.

IMPORTANT SAFETY INFORMATION

SAFETY

IMPORTANT SAFETY INFORMATION CONTINUED...

This model is intended for use in vehicular slide gate applications:

Gate Classifications: CLASS I, II, III, & IV

Main AC Supply: 120 Vac or 240 Vac

Solar Power Max: 24 Vdc at 60 watts max.

Input Rating:

• CSL24V: 10 Amps at 120 Vac or 2 Amps at 240 Vac

• CSL24VH: 12 Amps at 120 Vac

Input Rating Excluding Accessory Outlets:

• CSL24V: 4 Amps at 120 Vac or 2 Amps at 240 Vac

• CSL24VH: 6 Amps at 120 Vac

*Input Rating of Accessory Outlets: 6 Amps at 120 Vac

*NOTE: The accessory outlets are not connected for the 240 Vac rating.

Main Supply (Motor): 24 Vdc

Accessory Power: 24 Vdc 500 mA Max for ON or SW (switched)

NOTE: Increased accessory power drawn from the operator will shorten the

battery back-up duration or decrease cycle count for solar applications.

OPERATOR SPECIFICATIONS + CARTON INVENTORY & OPERATOR DIMENSIONS

INTRODUCTION

OPERATOR SPECIFICATIONS

Heater Draw (Optional): 325 watts (120 Vac ONLY)

Maximum Gate Weight: 1500 lbs.

Maximum Gate Travel Distance: 50 feet

Maximum Gate Speed: 1 foot/second

Daily Cycle Rate AC power: Continuous duty

Ambient Temperature:

• Without Heater: -20°C to 60°C (-4°F to 140°F)

• With Heater: -40°C to 60°C (-40°F to 140°F)

Fuse Protection Battery: 30 Amp

Fuse Protection DC Power: 30 Amp

CARTON INVENTORY & OPERATOR DIMENSIONS

Operator

Cover

Key (2)

Battery 12 Vdc 7AH (2)

Warning Signs (2) and Warranty Card

NOT SHOWN: Documentation Packet, Chain #41 - 30 feet, Eye Bolt Kit

14.6"

20"

21.1"

Battery Tray for Model

CSL24V ONLY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Chamberlain Toröffner Handbücher

Chamberlain

Chamberlain LiftMaster CSW200UL Series Bedienungsanleitung

Chamberlain

Chamberlain Estate Series X1 LiftMaster Professional Leitfaden

Chamberlain

Chamberlain SL 1000-B3 Bedienungsanleitung

Chamberlain

Chamberlain 128REV Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional SW420 Bedienungsanleitung

Chamberlain

Chamberlain RSW12UL Bedienungsanleitung

Chamberlain

Chamberlain SGO500 Bedienungsanleitung

Chamberlain

Chamberlain ELITE Series Bedienungsanleitung

Chamberlain

Chamberlain CSW200UL8 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster CSL24V Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional SW420 Bedienungsanleitung

Chamberlain

Chamberlain SectionalLift Plus Bedienungsanleitung

Chamberlain

Chamberlain LIFTMASTER PROFESSIONAL MSLDCBB Handbuch

Chamberlain

Chamberlain LiftMaster Professional SLY2500 Bedienungsanleitung

Chamberlain

Chamberlain MyQ Smart Garage Hub Bedienungsanleitung

Chamberlain

Chamberlain Elite RSL12V Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster PROFESSIONAL LYN300 Series Bedienungsanleitung

Chamberlain

Chamberlain Elite SL3000UL Bedienungsanleitung

Chamberlain

Chamberlain Motorlift HC260ML Bedienungsanleitung

Chamberlain

Chamberlain LYN300 Series Bedienungsanleitung

Chamberlain

Chamberlain MotorLift 808EML1 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional SL585 Bedienungsanleitung

Chamberlain

Chamberlain Elite SL3000UL Montage- und Bedienungsanleitung

Chamberlain

Chamberlain ART200K Bedienungsanleitung

Beliebte Toröffner Handbücher anderer Marken

CAME

CAME FROG-PM4 Bedienungsanleitung

SOMFY

SOMFY FX230 Bedienungsanleitung

Aprimatic

Aprimatic ONDA 500 Bedienungsanleitung

Turnstiles

Turnstiles FSW 900 Bedienungsanleitung

Erreka

Erreka BUL BL33 Betriebsanleitung

Erreka

Erreka VULCAN S Bedienungsanleitung

Beninca

Beninca R1-2 WBV Bedienungsanleitung

Erreka

Erreka VULCAN D Bedienungsanleitung

Motorline professional

Motorline professional FORT Bedienungsanleitung

Beninca

Beninca BOB5024 Bedienungsanleitung

AGA

AGA GATEMASTER 900 HD Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Westfalia

Westfalia 85 27 06 Bedienungsanleitung

CAME

CAME F500 Bedienungsanleitung

Extel

Extel VERA Bedienungsanleitung

Comunello Automation

Comunello Automation ABACUS 220 Bedienungsanleitung

CAME

CAME FA40230CB Bedienungsanleitung

Mighty Mule

Mighty Mule 200 E-Z GATE OPENER UL325 SERIES Bedienungsanleitung