Chamberlain Liftmaster ULTRX900R Bedienungsanleitung

Carton Inventory

Overview

The Ultra RX - Extreme Range Receiver has a

10-24Vac/Vdc operation. The Receiver has 4

Channels, 2 Transistors and 2 Relays. The Receiver

can control up to 4 devices.

Receiver

Model ULTRX900R

Ultra RX - Extreme Range Receiver

Setup

10-24 Vac

10-24 Vdc

NOTE: Polarity does not matter.

Power Connections

Relay Outputs

The Receiver has 2 Relays and 2 Transistor (Open

Collector) Outputs to control up to 4 devices.

Higher Amperage (10 amp) applications that are

directly controlled, should use Relay Channels 1

and 2.

Relay 1:

11: Common

12: Ch 1 Normal Open

13: Ch 1 Normal Closed

132456789101112 13

Relay 2:

8: Common

9: Ch 2 Normal Open

10: Ch 2 Normal Closed

Lower Amperage (500 ma or lower) applications that

are indirectly controlled, should use Transistor Output

Channels 3 and 4.

Channel 3:

Terminal 5

Channel 4:

Terminal 4

132456789101112 13

Dipswitch Settings

NOTE: To verify, apply a resistance load of 200 ohms

between positive power (1) and terminal 6 or 4.

Measure voltage between negative power (3) and

terminal 6 or 4. When transmitter signal is received,

the transistor should clamp the voltage down.

NOTE: The Dipswitches on the

Receiver can be accessed by

removing the screw on the

bottom of the Receiver.

NOTE: Do not connect power until instructed to do so.

Default Dipswitch configuration.

11312111098765432

Program

NOTE: If the Receiver will be programmed as a GCU

to a Primary Device proceed to "Alternate: Program

as GCU" section. The following steps apply only if the

Receiver will be used by itself.

Step 1: Ensure the Receiver does not have power

and Dipswitch #1 is set to the

OFF position.

NOTE: If Receiver is in this

Mode, there can be no other

900 Mhz units in the network.

Step 2: Connect power (as shown in Setup: Power

Connections).

Step 3: Within 15 seconds, press and hold a button

on a remote control transmitter. The receiver will buzz

indicating programming is successful.

Additional Remote Control Transmitters:

To program additional remote control transmitters,

repeat Step 3 above with each remote control

transmitter (within 10 seconds of each other) or

repeat Steps 1-3.

When all the remote control transmitters have been

programmed, wait 15 seconds for the Receiver to

leave Learn Mode. The Receiver will buzz twice

indicating it is ready for use.

Dipswitch Time

OFF 0.5 Sec

ON 5 Sec

Channel 4:

NOTE: These steps apply only if more than one

Receiver is being used.

Step 1: Ensure the

Receiver does not have

power. Set Dipswitch #1 to

the ON position in each

Receiver.

Step 2: Select the Identity for the Receiver (set as a

GCU) by changing the Dipswitches as shown in the

chart below.

Receiver ID Switch #2 Switch #3

2 ON OFF

3 OFF ON

4ON ON

Alternate: Program as GCU

Dipswitch Dipswitch Time

#2 #3

OFF OFF 0.5 Sec

ON OFF 5 Sec

OFF ON 1 Min

ON ON Toggle

Channel 3:

Output Timing

Dipswitch Dipswitch Time

#4 #5

OFF OFF 0.5 Sec

ON OFF 5 Sec

OFF ON 1 Min

ON ON Toggle

Channel 1:

Dipswitch Dipswitch Time

#6 #7

OFF OFF 0.5 Sec

ON OFF 5 Sec

OFF ON 1 Min

ON ON Toggle

Channel 2:

Door Strike or Magnetic Lock

Step 1: Connect relays (as shown in Setup: Relay

Outputs and the charts below).

NOTE: If a Door Strike is used, a separate power

supply is required.

If a Magnetic Lock is used, use the Normally Closed

connections (see below).

132 4 5 6 7 8 9 10 11 12

N/O

COM N/C

N/O

COM N/C

132 4 5 6 7 8 9 10 11 12

N/O

COM N/C

N/O

COM N/C

GCU

Program Accessories

Single Pushbutton Control (WPB1LM)

Step 1: Connect relays (as shown in Setup: Relay

Outputs).

Step 2: Connect power (as shown in Setup: Power

Connections).

Step 3: Press and Release the

Learn button on the Pushbutton

Control.

The Receiver will buzz and the LED

will blink 3 times indicating

programming is successful.

If the memory in the Pushbutton Control needs to be

cleared, press the Learn button until a tone is heard.

Refer to the Pushbutton Control manual for mounting

and operating instructions.

Gate Access Panel (GAPLM)/Keypad

Step 1: Connect relays (as shown in Setup: Relay

Outputs).

Step 2: Connect power (as shown in Setup: Power

Connections).

Step 3: On the GAPLM or Keypad, enter Master PIN

Number, followed by the Receiver Identity (1-4) as

determined in Setup: Additional Receivers.

The Receiver will buzz and the LED will blink 3 times

indicating programming is successful.

Refer to the GAPLM/Keypad manual for mounting

and operating instructions.

2 3

789

Cancel

Installation

Step 1: Reattach cover with screw.

Step 2: Mount the Receiver with

the Terminal Block at the bottom

and the antenna hanging straight

down.

NOTE: Metal surfaces can shorten the

range of the Receivers. If mounting on a metal

surface and long range is required, use a

non-metallic spacer to move the Receiver away from

the metal surface.

1 2 3 4 5 6 7 8 9 10 11 12 13

Optional external power

input 10-24 Vac or DC

Optional external power

input 10-24 Vac or DC

Door

Strike

Transfomer/

Power Supply

Door Strike- Normally Open (N/O) Connection

Transfomer/

Power Supply

Magnetic

Lock

Magnetic Lock- Normally Closed (N/C) Connection

Relay 2

Relay 1

Relay 2

Relay 1

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited,

except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:

1-800-528-2806

www.liftmaster.com

Operation

GAPLM/Keypad

On the GAPLM/Keypad enter any valid PIN Number

followed by Identity (1-4).

If the Receiver gets a request a success tone is

heard.

If a fail tone is heard, check the batteries in the

GAPLM/Keypad or try again.

Single Pushbutton Control (WPB1LM)

Push the button on the Pushbutton Control.

If the Receiver gets a request a success tone is

heard.

If a fail tone is heard, check the batteries in the

Pushbutton Control or try again.

Clear Memory

When the Receiver has power,

press the Learn button until the

LED blinks a total of 8 times.

ON WDE

12345678

Inhaltsverzeichnis

Andere Chamberlain Empfänger Handbücher

Chamberlain

Chamberlain LiftMaster Star250 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 423LM Bedienungsanleitung

Chamberlain

Chamberlain 365LM Bedienungsanleitung

Chamberlain

Chamberlain STAR1000 Bedienungsanleitung

Chamberlain

Chamberlain 955D Bedienungsanleitung

Chamberlain

Chamberlain TriCode TCR1 Bedienungsanleitung

Chamberlain

Chamberlain 050DCTWFLK Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 312HMC Bedienungsanleitung

Chamberlain

Chamberlain PPWR Bedienungsanleitung

Chamberlain

Chamberlain 850LM Bedienungsanleitung

Chamberlain

Chamberlain 850LMC Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional 323LM Bedienungsanleitung

Chamberlain

Chamberlain 955D Bedienungsanleitung

Chamberlain

Chamberlain 045DCT Bedienungsanleitung

Chamberlain

Chamberlain TRICODE TCR2 DUAL Bedienungsanleitung

Chamberlain

Chamberlain 860LM Bedienungsanleitung

Chamberlain

Chamberlain 41A6128 Bedienungsanleitung

Chamberlain

Chamberlain 635LM - Sears LiftMaster Chamberlain Bedienungsanleitung

Chamberlain

Chamberlain CHAMBERLAIN 635LM Bedienungsanleitung

Chamberlain

Chamberlain 860EV Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional 365LM Bedienungsanleitung

Chamberlain

Chamberlain TriCode TCR2 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional CPWR3 Bedienungsanleitung

Chamberlain

Chamberlain STAR450 Series Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung