Chamberlain Ultra RX ULTRX900R Bedienungsanleitung

Carton Inventory

Overview

The Ultra RX - Extreme Range Receiver has a

10-24Vac/Vdc operation with low power consumption

(150 ua). The Receiver has 4 Channels, 2 Transistors

and 2 Relays. The Receiver can control up to

4 devices.

Receiver

Model ULTRX900R

Ultra RX - Extreme Range Receiver

Setup

1 32 4 5 6 7 8 9 10 11 12 13

10-24 Vac

1 32 4 5 6 7 8 9 10 11 12 13

10-24 Vdc

NOTE: Polarity does not matter.

Power Connections

Relay Outputs

The Receiver has 2 Relays and 2 Transistor (Open

Collector) Outputs to control up to 4 devices.

Higher Amperage (10 amp) applications that are

directly controlled, should use Relay Channels 1

and 2.

Relay 1:

11: Common

12: Ch 1 Normal Open

13: Ch 1 Normal Closed

1 32 4 5 6 7 8 9 10 11 12 13

Relay 2:

8: Common

9: Ch 2 Normal Open

10: Ch 2 Normal Closed

Lower Amperage (500 ma or lower) applications that

are indirectly controlled, should use Transistor Output

Channels 3 and 4.

Channel 3:

Terminal 6

Channel 4:

Terminal 4

1 32 4 5 6 7 8 9 10 11 12 13

Dipswitch Settings

NOTE: If using the Receiver with a Gate Control Unit

(GCU) proceed to Program with Gate Control Unit

(GCU).

NOTE: The Dipswitches on the

Receiver can be accessed by

removing the screw on the

bottom of the Receiver.

Ensure the Receiver does

not have power. Set

Dipswitch #1 to the ON

position.

NOTE: These steps apply only if more than one

Receiver is being used.

Step 1: Ensure the

Receiver does not have

power. Set Dipswitch #1 to

the ON position in each

Receiver.

Step 2: Set the Identity of each additional Receiver

by changing the Dipswitches as shown in the chart

below.

Receiver ID Switch #2 Switch #3

2 ON OFF

3 OFF ON

4ON ON

Additional Receivers

NOTE: Do not connect power until instructed to do so.

Output Timing

Dipswitch Dipswitch Time

#4 #5

OFF OFF 0.5 Sec

ON OFF 5 Sec

OFF ON 1 Min

ON ON Toggle

Channel 1:

Dipswitch Dipswitch Time

#6 #7

OFF OFF 0.5 Sec

ON OFF 5 Sec

OFF ON 1 Min

ON ON Toggle

Channel 2:

Program

NOTE: If the Receiver will be programmed with a

GCU or an accessory proceed to Program with GCU

or Program Accessories.

The following steps apply only if the Receiver will be

used by itself.

Step 1: Ensure the Receiver

does not have power and

Dipswitch #1 is set to the OFF

position.

NOTE: If Receiver is in this Mode, there can be no

other 900 Mhz units in the network.

Step 2: Connect power (as shown in Setup: Power

Connections).

Step 3: Within 15 seconds, press and hold a button

on a remote control transmitter. The receiver will buzz

indicating programming is successful.

Additional Remote Control Transmitters:

To program additional remote control transmitters,

repeat Step 3 above with each remote control

transmitter (within 10 seconds of each other) or

repeat Steps 1-3.

When all the remote control transmitters have been

programmed, wait 15 seconds for the Receiver to

leave Learn Mode. The Receiver will buzz twice

indicating it is ready for use.

Output Timing

Dipswitch Dipswitch Time

#4 #5

OFF OFF 0.5 Sec

ON OFF 5 Sec

OFF ON 1 Min

ON ON Toggle

Channel 1:

Dipswitch Dipswitch Time

#6 #7

OFF OFF 0.5 Sec

ON OFF 5 Sec

OFF ON 1 Min

ON ON Toggle

Channel 2:

Dipswitch Dipswitch Time

#2 #3

OFF OFF 0.5 Sec

ON OFF 5 Sec

OFF ON 1 Min

ON ON Toggle

Channel 3:

Dipswitch Time

OFF 0.5 Sec

ON 5 Sec

Channel 4:

Program with Gate Control

Unit (GCU)

NOTE: The Dipswitches on the

Receiver can be accessed by

removing the screw on the

bottom of the Receiver.

Door Strike or Magnetic Lock

Step 1: Connect relays (as shown in Setup: Relay

Outputs and the charts below).

NOTE: If a Door Strike is used, a separate power

supply is required.

If a Magnetic Lock is used, use the Normally Closed

connections (see below).

132 4567891011

COM

N/C

Door

Strike

Transformer/

Power Supply

Optional external power

input 10-24 Vac or DC

Door Strike- Normally Open (N/O) Connection

N/O

1324567891011

COM

N/C

Magnetic

Lock

Transformer/

Power Supply

Magnetic Lock- Normally Closed (N/C) Connection

Optional external power

input 10-24 Vac or DC

N/O

GCU

Program Accessories

Single Pushbutton Control (WPB1LM)

Step 1: Connect relays (as shown in Setup: Relay

Outputs).

Step 2: Connect power (as shown in Setup: Power

Connections).

Step 3: Press and Release the

Learn button on the Pushbutton

Control.

The Receiver will buzz and the LED

will blink 3 times indicating

programming is successful.

If the memory in the Pushbutton Control needs to be

cleared, press the Learn button until a tone is heard.

Refer to the Pushbutton Control manual for mounting

and operating instructions.

Gate Access Panel (GAPLM)/Keypad

Step 1: Connect relays (as shown in Setup: Relay

Outputs).

Step 2: Connect power (as shown in Setup: Power

Connections).

Step 3: On the GAPLM or Keypad, enter Master PIN

Number, followed by the Receiver Identity (1-4) as

determined in Setup: Additional Receivers.

The Receiver will buzz and the LED will blink 3 times

indicating programming is successful.

Refer to the GAPLM/Keypad manual for mounting

and operating instructions.

2 3

5 6

7 8 9

0 #

a c

Installation

Step 1: Reattach cover with screw.

Step 2: Mount the Receiver with

the Terminal Block at the bottom

and the antenna hanging straight

down.

NOTE: Metal surfaces can shorten the

range of the Receivers. If mounting on a metal

surface and long range is required, use a

non-metallic spacer to move the Receiver away from

the metal surface.

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited,

except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:

1-800-528-2806

www.liftmaster.com

Operation

GAPLM/Keypad

On the GAPLM/Keypad enter any valid PIN Number

followed by Identity (1-4).

If the Receiver gets a request a success tone is

heard.

If a fail tone is heard, check the batteries in the

GAPLM/Keypad or try again.

Single Pushbutton Control (WPB1LM)

Push the button on the Pushbutton Control.

If the Receiver gets a request a success tone is

heard.

If a fail tone is heard, check the batteries in the

Pushbutton Control or try again.

Clear Memory

When the Receiver has power,

press the Learn button until the

LED blinks a total of 8times.

1234567

Inhaltsverzeichnis

Andere Chamberlain Empfänger Handbücher

Chamberlain

Chamberlain LiftMaster 422LM Bedienungsanleitung

Chamberlain

Chamberlain 050DCTWF Bedienungsanleitung

Chamberlain

Chamberlain 860EV Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 365LM Bedienungsanleitung

Chamberlain

Chamberlain 050DCTBMC Bedienungsanleitung

Chamberlain

Chamberlain 635LM - Sears LiftMaster Chamberlain Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster PROFESSIONAL 635-315LM Bedienungsanleitung

Chamberlain

Chamberlain STAR450 Series Bedienungsanleitung

Chamberlain

Chamberlain 5002EX Bedienungsanleitung

Chamberlain

Chamberlain 41A6128 Bedienungsanleitung

Chamberlain

Chamberlain 8002E Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional CPWR3 Bedienungsanleitung

Chamberlain

Chamberlain 850LM Bedienungsanleitung

Chamberlain

Chamberlain 955CB Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Star250 Bedienungsanleitung

Chamberlain

Chamberlain 050ACTWF Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster CPT1 Bedienungsanleitung

Chamberlain

Chamberlain merlin CSTAR250 Bedienungsanleitung

Chamberlain

Chamberlain TRICODE TCR2 DUAL Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 312HMC Bedienungsanleitung

Chamberlain

Chamberlain STAR450 Series Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Star250 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 850LM Bedienungsanleitung

Chamberlain

Chamberlain TRICODE TCG2 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung