Chauvet DJ Intimidator Spot 255 IRC Bedienungsanleitung

Quick Reference Guide

Intimidator™ Spot 255 IRC QRG EN

About This

Guide The Intimidator™ Spot 255 IRC Quick Reference Guide (QRG) has basic

product information such as mounting, menu options, and DMX values.

Download the User Manual from www.chauvetlighting.com for more

details.

Disclaimer The information and specifications contained in this QRG are subject to

change without notice.

Safety Notes These Safety Notes include important information about installation, use,

and maintenance.

•This product is not intended for permanent installation.

•ONLY connect this product to a grounded and protected circuit.

•Always disconnect from power before cleaning or replacing the fuse.

•DO NOT look at the light source when the product is on.

•Make sure the power cord is not crimped or damaged.

•Never disconnect this product from power by pulling on the cord.

•When mounting this product overhead, use a safety cable.

•DO NOT allow flammable materials close to the unit while operating.

•DO NOT touch this product when it is operating because it may be hot.

•The voltage of the outlet to which you are connecting this product must

be within the range stated on the decal or rear panel of the product.

•This product is for indoor use only! (IP20) To prevent risk of fire or

shock, do not expose this product to rain or moisture.

•Always mount this product in a location with adequate ventilation, at

least 20 in (50 cm) from adjacent surfaces.

•Be sure that no ventilation slots on the unit’s housing are blocked.

•Never connect this product to a dimmer or rheostat.

•Replace the fuse with another of the same type and rating.

•ONLY use the hanging/mounting bracket to carry this product.

•The maximum ambient temperature is 104 °F (40 °C). Do not operate

this product at higher temperatures.

•In the event of a serious operating problem, stop using immediately.

•DO NOT open this product. It contains no user-serviceable parts.

•To eliminate unnecessary wear and improve its lifespan, during periods

os non-use completely disconnect the product from power via the

breaker or by unplugging it.

Contact Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux, contact

your distributor to request support or return a product. Visit

www.chauvetlighting.com for contact information.

Intimidator™ Spot 255 IRC QRG EN

What Is

Included •Intimidator™ Spot 255 IRC

•Hanging Bracket with Mounting

Hardware

•Power Cord

•Warranty Card

•Quick Reference Guide

To Begin Unpack your Intimidator™ Spot 255 IRC and make sure you have received

all parts in good condition. If the box or contents appear damaged, notify the

carrier immediately, not Chauvet.

Description The Intimidator™ Spot 255 IRC is an exceptionally bright, 50 W LED

moving head spot designed for large events. Simple navigation and full text

readout with high-contrast is displayed on a full-color LCD display. An

easy-access gobo door allows for quick gobo changes. Motorized focus

emits crisp projections at almost any distance. A 3-facet rotating prism splits

the beam for great effects and a large coverage area. Built-in effect macros

and move-in-black featuresminimize programming time. Operation

options include Auto and Sound-Active programs, DMX and Master/

Slave mode. Pan and tilt ranges are user-selectable. Wireless control and

triggering are obtainable with the IRC-6 available from Chauvet. The

Intimidator™ Spot 255 IRC fits best in the CHS-X5X VIP Gear Bag from

Chauvet.

Overview

Yoke

LCD

Display

Control

Buttons

IR Sensor

Indicator

Light

Gobo

Access

Door

Cooling

Fan

Intimidator™ Spot 255 IRC QRG EN

Overview

(cont.)

AC Power This product has an auto-ranging power supply that can work with an input

voltage range of 100 to 240 VAC, 50/60 Hz.

To eliminate wear and improve its lifespan, during periods of non-use

completely disconnect from power via breaker or by unplugging it.

Fuse

Replacement 1. Disconnect the product from power.

2. Using a flat-head screwdriver, loosen the fuse holder and pull

straight out.

3. Remove the blown fuse from the holder and replace with a fuse of the

exact same type and rating.

4. Re-insert the fuse holder and reconnect power.

Front Panel View

Indicator

Light

Control Buttons

IR Sensor

Full Color

LCD Display

Back Panel View

Power Out

Cooling Fan

DMX In

DMX Out

Fuse Holder

Power In

Microphone

Intimidator™ Spot 255 IRC QRG EN

Infrared Remote

Control (IRC-6) The Intimidator™ Spot 255 IRC is compatible with the IRC-6 from Chauvet.

The following IRC-6 buttons are used with the Intimidator™ Spot 255 IRC:

•<BLACKOUT> - Turns LED on/off

•<AUTO> - Selects auto program mode (scrolling)

•<SOUND> - Selects Sound-Active mode

•<STROBE> - Strobing (0–20 Hz)

•<SPEED> - Pan/Tilt auto program speed (decreasing)

•<SENSITIVITY> - Selects sound sensitivity

•<%> - LED dimmer

•<MANUAL> - Gobo selection

•<FADE> - Color selection

•<R> - Color cycling rainbow

•<G> - Gobo cycle effect

•<B> - Color rainbow and gobo cycle effect

•<A> - Pan/Tilt manual adjustment

•<W> - Prism effect

•<+> - Increase

•<-> - Decrease

•<0> to <9> - Select auto program by number

•<UV> - No function

Intimidator™ Spot 255 IRC QRG EN

MountingBefore mounting this product, read the Safety Notes. Make sure the

mounting clamp is capable of supporting the w

eight of the product. For our

Chauvet line of mounting clamps, go to www.chauvetlighting.com/cables-

clamps-main.html.

Mounting

Diagram

When using only one mounting clamp, be sure to use a clamp with a

captive bolt to prevent accidental loosening.

Control Panel

Description Button Function

<MODE> Exits from the current menu or function

<UP> Navigates upwards through the menu list and increases the

numeric value when in a function

<DOWN> Navigates downwards through the menu list and decreases the

numeric value when in a function

<ENTER> Enables the currently displayed menu or sets the currently

selected value into the selected function

Mounting Clamp

Safety Cable

Hanging/Mounting

Bracket

Rubber Feet (x4)

for floor mounting

Intimidator™ Spot 255 IRC QRG EN

Menu Options

Main Function Programming Levels Description

Address 001–512 Sets the DMX starting address

Run Mode

DMX 13CH Selects DMX mode

08CH

Slave Slave 1–4 Selects Slave mode 1, 2 ,3, or 4

Sound Selects Sound-Active mode

Auto Selects Auto mode

IR Selects infrared control

Manual

Pan

000–255

0 to 540°

Pan Fine Fine control of panning

Tilt 0 to 270°

Tilt Fine Fine control of tilting

P/T Speed Pan/Tilt speed (fast to slow)

Color Selects color options

Gobo Selects Gobo options

Gobo

Rotation Rotation effect with increasing speed

Prism Selects 3-facet prism

Dimmer Sets dimmer value

Shutter Strobe effect with increasing speed

Special

Function Selects control functions

P/T Macro Selects pan/tilt movement macros

Setup

Pan Reverse OFF Normal pan operation

ON Reverse pan operation

Tilt Reverse OFF Normal tilt operation

ON Reverse tilt operation

Screen

Reverse OFF Normal display

ON Reverse display

Pan Angle 540 Selects the 540° pan angle range

360 Selects the 360° pan angle range

180 Selects the 180° pan angle range

Tilt Angle 270 Selects the 270° tilt angle range

180 Selects the 180° tilt angle range

090 Selects the 90° tilt angle range

Totem Up Selects upward pan and tilt range

Down Selects downward pan and tilt range

Sensitivity 001–100 Sound sensitivity control

Reset Resets the product

Factory Set Loads factory defaults

Sys Info

Ver: VX.X Displays the software version

Running Mode: XXXXX Displays the current running mode

DmxAddress: XXX Displays the current DMX address

Temperature: XXX Displays the LED temperature in Celsius

Intimidator™ Spot 255 IRC QRG EN

DMX Linking The Intimidator™ Spot 255 IRC can work with a DMX controller when

linked by DMX serial connections. Instructions for connecting and

configuring this product for DMX operation are in the User Manual. If you

are not familiar with DMX, download the DMX Primer from

www.chauvetlighting.com.

Starting

Address To ensure full access to all channels in each DMX mode, the highest

recommended DMX address is 500.

Master/Slave

Connection

The Intimidator™ Spot 255 IRC uses the DMX data connection for its

Master/Slave mode. Instructions for connecting and configuring this product

for Master/Slave operation are in the User Manual.

Intimidator™ Spot 255 IRC QRG EN

DMX Values

13CH

Channel Function Value Percent/Setting

1 Pan 000 ó255 0 to 540°

2 Fine Pan 000 ó255 Fine control of panning

3 Tilt 000 ó255 0 to 270°

4 Fine Tilt 000 ó255 Fine control of tilting

5 Speed 000 ó255 Pant/Tilt speed (fast to slow)

6 Color Wheel

000 ó006 White

007 ó013 Yellow

014 ó020 Pink

021 ó027 Green

028 ó034 Red

035 ó041 Light Blue

042 ó048 Kelly Green

049 ó055 Orange

056 ó064 Dark Blue

065 ó071 White + Yellow

072 ó078 Yellow + Pink

079 ó085 Pink + Green

086 ó092 Green + Red

093 ó099 Red + Light Blue

100 ó106 Light Blue + Kelly Green

107 ó113 Kelly Green + Orange

114 ó120 Orange + Dark Blue

121 ó127 Dark Blue + White

128 ó191 Color cycling rainbow with increasing speed

192 ó255 Reverse color cycling rainbow with increasing

speed

7 Gobo Wheel

064 ó071 Gobo 7 shake, slow to fast

072 ó079 Gobo 6 shake, slow to fast

080 ó087 Gobo 5 shake, slow to fast

088 ó095 Gobo 4 shake, slow to fast

096 ó103 Gobo 3 shake, slow to fast

104 ó111 Gobo 2 shake, slow to fast

112 ó119 Gobo 1 shake, slow to fast

120 ó127 Open

128 ó191 Cycle effect with increasing speed

192 ó255 Reverse cycle effect with increasing speed

Intimidator™ Spot 255 IRC QRG EN

DMX Values (cont.)

13CH

(cont.) Channel Function Value Percent/Setting

8 Gobo Rotation

000 ó007 No function

008 ó119 Rotation effect with increasing speed

120 ó231 Reverse rotation effect with increasing speed

232 ó255 Gobo bounce

9 Prism 000 ó015 Open

016 ó255 Prism on

10 Dimmer 000 ó255 0–100%

11 Shutter

000 ó003 Closed

004 ó007 Open

008 ó215 Strobe effect with increasing speed

216 ó255 Open

12 Control

Functions

000 ó007 No function

008 ó027 Blackout while pan/tilt moving

028 ó047 Blackout while moving gobo wheel

048 ó067 Disable blackout while pan/tilt/moving gobo

wheel

068 ó087 Blackout while moving color wheel

088 ó107 Disable blackout while pan/tilt/moving color wheel

108 ó127 Disable blackout while moving gobo/color wheel

128 ó147 Disable blackout while pan/tilt/moving

gobo/moving color wheel

148 ó157 Reset pan

158 ó167 Reset tilt

168 ó177 Reset color wheel

178 ó187 Reset gobo wheel

188 ó197 Reset prism

198 ó207 Reset all channels

208 ó255 No function

13 Movement

Macros

000 ó007 No function

008 ó023 Automatic movement 1

024 ó039 Automatic movement 2

040 ó055 Automatic movement 3

056 ó071 Automatic movement 4

072 ó087 Automatic movement 5

088 ó103 Automatic movement 6

104 ó119 Automatic movement 7

120 ó135 Automatic movement 8

136 ó151 Sound-active movement 1

152 ó167 Sound-active movement 2

168 ó183 Sound-active movement 3

184 ó199 Sound-active movement 4

200 ó215 Sound-active movement 5

216 ó231 Sound-active movement 6

232 ó247 Sound-active movement 7

248 ó255 Sound-active movement 8

Inhaltsverzeichnis

Sprachen:

Andere Chauvet DJ DJ-Equipment Handbücher

Chauvet DJ

Chauvet DJ EVE P-100 WW Bedienungsanleitung

Chauvet DJ

Chauvet DJ MotionOrb Bedienungsanleitung

Chauvet DJ

Chauvet DJ Freedom Par T6 Bedienungsanleitung

Chauvet DJ

Chauvet DJ Cumulus HP Bedienungsanleitung

Chauvet DJ

Chauvet DJ Intimidator Spot 160 ILS Bedienungsanleitung

Chauvet DJ

Chauvet DJ 4BAR LT BT Bedienungsanleitung

Chauvet DJ

Chauvet DJ WASH FX Bedienungsanleitung

Chauvet DJ

Chauvet DJ INTIMIDATOR SPOT 260 Bedienungsanleitung

Chauvet DJ

Chauvet DJ SHOCKER PANEL 180 Bedienungsanleitung

Chauvet DJ

Chauvet DJ COLORband PiX-M USB Bedienungsanleitung

Chauvet DJ

Chauvet DJ INTIMIDATOR SPOT 360X IP Bedienungsanleitung

Chauvet DJ

Chauvet DJ Vivid Drive 28N Bedienungsanleitung

Chauvet DJ

Chauvet DJ 4BAR USB Bedienungsanleitung

Chauvet DJ

Chauvet DJ COREpar 80 USB Bedienungsanleitung

Chauvet DJ

Chauvet DJ Hurricane HAZE 1D Bedienungsanleitung

Chauvet DJ

Chauvet DJ EZ Pin Zoom Pack Bedienungsanleitung

Chauvet DJ

Chauvet DJ XPRESS-RACK 1024 Bedienungsanleitung

Chauvet DJ

Chauvet DJ EZGobo Bedienungsanleitung

Chauvet DJ

Chauvet DJ Beamer 8 Bedienungsanleitung

Chauvet DJ

Chauvet DJ Hurricane 1400 Bedienungsanleitung

Chauvet DJ

Chauvet DJ LED Pinspot 2 Bedienungsanleitung

Chauvet DJ

Chauvet DJ DMX-RT4 Bedienungsanleitung

Chauvet DJ

Chauvet DJ Intimidator Scan 360 Bedienungsanleitung

Chauvet DJ

Chauvet DJ SHOCKER PANEL 480 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung