Chauvet DJ SHOCKER PANEL 180 Bedienungsanleitung

Quick Reference Guide

Shocker™ Panel 180 USB QRG EN

About This Guide

The Shocker Panel 180 USB Quick Reference Guide (QRG) has basic product

information such as mounting, menu options, and DMX values. For more

information, download the User Manual from the Chauvet

website:

http://www.chauvetlighting.com.

Disclaimer

The information and specifications contained in this QRG are subject to change

without notice.

Safety Notes

The following Safety Notes include important information about installation, use,

and maintenance.

•Always connect the product to a grounded circuit.

•Make sure the power cord is not crimped or damaged.

•Always disconnect the product from the power source before cleaning it or

replacing the fuse.

•Never disconnect the product from the power source by pulling or tugging on

the cord.

•If mounting the product overhead, make sure there is adequate support for the

product’s weight and always secure the product using a safety cable.

•Make sure there are no flammable materials close to the product when it is

operating.

•Avoid direct eye exposure to the light source while the product is on.

•Do not touch the product’s housing when the product is operating because the

housing can be very hot.

•The product is not intended for permanent installation.

•The product is for indoor use only. It is rated at IP20.

•Do not expose the product to rain or moisture.

•Always connect the product to a power source that is within the voltage range

stated on the label or rear panel of the product.

•Never connect the product to a dimmer or rheostat.

•Make sure to replace the fuse with another of the same type and rating.

•Always install the product in a location with adequate ventilation.

•Always leave at least 20 in (50 cm) between the product and adjacent surfaces.

•Be sure that no ventilation slots on the product’s housing are blocked.

•Do not operate the product at an ambient temperature higher than

104 °F (40 °C).

•Never carry the product by the power cord or any moving part.

•Always use the mounting clamp or hanging/mounting bracket to carry the

product.

•If there is a serious operating problem, stop using the product immediately.

•Never try to repair the product. Repairs carried out by untrained people can

lead to damage or malfunction.

•To eliminate wear and improve its lifespan, during periods of non-use

completely disconnect from power via breaker or by unplugging it.

Contact

Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux, contact your

distributor to request support or return a product. Visit www.chauvetlighting.com

for

contact information.

What Is Included

•Shocker Panel 180 USB

•Power cord

•Warranty card

•Quick Reference Guide

Shocker™ Panel 180 USB QRG EN

To Begin

Carefully unpack the Shocker Panel 180 USB and check that all the parts are in

the package, and are in good condition.

If the box, or any of the contents, appear damaged from shipping, or show signs

of mishandling, save all packaging and file a claim with the carrier immediately,

do not notify Chauvet

. Failure to report damage to the carrier immediately, or

failure to have all packaging available for inspection, could invalidate your claim.

For other issues, such as missing components or parts, damage not related to

shipping, or concealed damage, file a claim with Chauvet

within 7 days of

delivery. For information on contacting Chauvet, see Contact Us at the end of this

QRG.

Description

The Shocker Panel 180 USB is a high-powered LED strobe light with 4 zones of

control for a variety of attractive effects that create stunning visuals.

It has a

rugged die-cast housing, and operates in IR mode, wired or wireless DMX,

Master-Slave, or Standalone modes.

DMX control wirelessly with the convenient

built in D-Fi™ USB port.

Overview

WARNING! DO NOT plug anything other than a D-Fi™ USB into the USB

port. Doing so may cause damage to the product.

AC Power

Shocker Panel 180 USB has an auto-ranging power supply that works with a

voltage range of 100–240 VAC, 50/60 Hz.

To eliminate wear and improve its lifespan, during periods of non-use

completely disconnect from power via breaker or by unplugging it.

Power Linking

Power linking is when products are daisy chained together through their Power In

and Power Out ports, so that many products can be powered from one outlet.

For the maximum number of Shocker Panel 180 USBs that

can be

power linked at 120 V or at 240 V, see the User Manual or the label

on the

product. The User Manual is available at the Chauvet website:

http://www.chauvetlighting.com.

DMX Out

Display

Control Buttons

Microphone

Safety Loop

DMX In

Power In

Power Out

Fuse Holder

D-Fi™

USB Port

Shocker™ Panel 180 USB QRG EN

Fuse Replacement

1. Disconnect the product from power.

2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.

3. Pry the safety cap out of the housing.

4. Remove the blown fuse from the holder and replace with a fuse of the exact

same type and rating.

5. Re-insert the fuse holder and reconnect power.

Disconnect the product from power before replacing the fuse.

Mounting

Before mounting this product, read the Safety Notes. Make sure the mounting

clamps (such as CLP-15Nclamps from Chauvet) are

capable of supporting the

weight of the product. For the Chauvet line of mounting clamps, g

o to

www.chauvetlighting.com/cables-clamps-main.html.

Mounting Diagram

Hanging/Mounting

Bracket

(also used as floor

supports)

Mounting Clamp

Bracket

Adjustment

Knobs

Safety Cable

Shocker™ Panel 180 USB QRG EN

Control Panel

Description

Button

Function

<MENU>

Exits from the current menu or function

<UP>

Navigates upwards through the menu list or increases the

numeric value when in a function

<DOWN>

Navigates downwards through the menu list or decreases the

numeric value when in a function

<ENTER>

Enables the currently displayed menu or sets the currently

selected value into the selected function

Menu Map

Main Function

Programming Levels

Description

DMX Personality

and Starting

Address

2-CH

d 1–d512

Sets 2-channel DMX mode and DMX

starting address

5-CH

Sets 5-channel DMX mode and DMX

starting address

8-CH

Sets 8-channel DMX mode and DMX

starting address

Auto Programs P-- P 1–P 8

Sets Auto mode programs 1–8

(P 8 is 1–7)

Program Speed

S--

S 1–S100

Sets Auto mode speed

Customized U--

d 0–d255

Sets dimmer

S 0–S255

Sets strobe, slow to fast

Sound-Active Snd

Snd1

Sets Sound-Active mode

Snd2

Sound Sensitivity

SenS

u 0–u100

Sets sound sensitivity

Infrared SET

Sets IR mode

OFF

Temperature

Temp

Shows current temperature of product

Shocker™ Panel 180 USB QRG EN

DMX Linking

The Shocker Panel 180 USB works with a DMX controller. Information about

configuring Shocker Panel 180 USB for DMX operation is in the

User Manual, which is available from the Chauvet website:

http://www.chauvetlighting.com. Information about DMX is in the Chauvet DMX

Primer, which is available from the Chauvet website

http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf.

Starting Address

The Shocker Panel 180 USB has 2-, 5-, and 8-channel DMX personalities. To

ensure full access to all channels in each DMX mode, the highest recommended

DMX address for this product is 505.

Master/Slave

Connection

The Shocker Panel 180 USB works in Master/Slave mode. Information about

configuring this product for Master/Slave mode is in the User Manual, which is

available from the Chauvet website: http://www.chauvetlighting.com.

IRC-6

(Infrared Remote

Control)

The Shocker Panel 180 USB is compatible with the IRC-6 from Chauvet DJ. For

more information on the IRC-6 or to download instructions, go to the Chauvet

website: http://www.chauvetlighting.com.

D-Fi™ USB

Connectivity

The Shocker Panel 180 USB is able to become a D-Fi™ wireless

receiver/transmitter with the use of the D-Fi™ USB from Chauvet

DJ. Simply set

the DIP switch D-Fi™ receiving/transmitting channel, plug it into the USB p

ort

then set the product's DMX personality and DMX a

ddress. Further instructions for

connecting and configuring this product for D-

Fi™ USB operation are in the User

Manual.

WARNING! DO NOT plug anything other than a D-

Fi™ USB into the USB

port. Doing so may cause damage to the product.

Once plugged in, the D-Fi™ USB will take over the product. Wired DMX,

manual display control/menu buttons and IRC-6

will be unavailable until you

unplug the D-Fi™ USB. The priority levels are:

1. D-Fi™ USB

2. Wired DMX

3. IRC-6 Remote Control

4. Manual Digital Display/Menu Buttons

IR Sensor

Shocker™ Panel 180 USB QRG EN

DMX Channel Assignments

8-CH

Channel

Function

Value

Percent/Setting

1 Zone 1

000

005

No function

006

249

Strobe rate (slow to fast)

250ó255

Continuous on (blinder effect)

2 Zone 2

000

005

No function

006ó249

Strobe rate (slow to fast)

250

255

Continuous on (blinder effect)

3 Zone 3

000

005

No function

006

249

Strobe rate (slow to fast)

250

255

Continuous on (blinder effect)

4 Zone 4

000ó005

No function

006

249

Strobe rate (slow to fast)

250

255

Continuous on (blinder effect)

5 Auto/Sound-Active

Programs

000ó020

No function

021

040

Auto program 1

041ó060

Auto program 2

061

080

Auto program 3

081

100

Auto program 4

101

120

Auto program 5

121

140

Auto program 6

141ó160

Auto program 7

161

180

Auto program 8 (Auto programs 1–7)

181

225

Sound-active mode 1

226

255

Sound-active mode 2

Auto Speed

(when Channel 5 is

set at

021

–

180

)

000ó255

Auto program speed (slow to fast)

Sound Sensitivity

(when Channel 5 is

set at

181

–

255

)

000ó010

No function

011ó255

Sound sensitivity

Dimmer

000

255

0–100%

Strobe All Zones

(when Channel 1-4

set at 006–255)

000

005

No function

006ó255

Strobe rate (slow to fast)

Shocker™ Panel 180 USB QRG EN

5-CH

Channel

Function

Value

Percent/Setting

1 Dimmer

000

005

No function

006

255

0–100%

2 Strobe Speed

000ó005

No function

006

255

Strobe speed (slow to fast)

Shutter

(When Channel 2 is

set at 006–255)

000

005

Open

006ó255

Pulse speed (slow to fast)

4 Strobe Effects

(When Channel 2 is

set at 006–255)

000

005

No function

006

042

Ramp up

043

085

Ramp down

086ó128

Ramp up – ramp down

129

171

Random

172

214

Lightning

215

255

Spikes

5 Zone Strobe

Macros

000

005

No function

006ó042

Macro 1(slow to fast)

043

085

Macro 2 (slow to fast)

086

128

Macro 3(slow to fast)

129

171

Macro 4 (slow to fast)

172

214

Macro 5 (slow to fast)

215ó255

Macro 6 (slow to fast)

2-CH

Channel

Function

Value

Percent/Setting

1 Strobe Speed

000

001

No function

002ó249

Strobe speed (slow to fast)

250

255

Continuous on (blinder effect)

Dimmer

000

255

0–100%

Shocker™Panel 180 USB Zones for DMX Control

Shocker™ Panel 180 USB GRR ES

Acerca de Esta

Guía

La Guía de Referencia Rápida (GRR) del Shocker Panel 180 USB contiene

información básica sobre el producto, como montaje, opciones de menú y valores

DMX. Para más información, descargue el Manual de Usuario del sitio web de

Chauvet www.chauvetlighting.com/product-manuals-literature/.

Exención de

Responsabilidad

La información y especificaciones contenidas en esta GRR están sujetas a cambio

sin previo aviso.

Notas de

Seguridad

Estas notas de seguridad incluyen información importante sobre el montaje, uso y

mantenimiento.

•Conecte siempre el producto a un circuito con toma de tierra para evitar el riesgo

de electrocución.

•Asegúrese de que el cable de alimentación no está retorcido ni estropeado.

•

Desconecte siempre el producto de la fuente de alimentación antes de limpiarlo o

cambiar el fusible.

•Nunca desconecte el producto de la fuente de alimentación agarrando o tirando

del cable.

•Si monta el producto en altura, asegúrese de que el soporte es adecuado para el

peso del producto, y asegure siempre el producto con un cable de seguridad.

•Asegúrese de que no hay materiales inflamables cerca del producto cuando esté

en funcionamiento.

•

Evite la exposición directa de los ojos a la fuente de luz mientras es producto esté

encendido.

•No toque la carcasa del producto cuando el producto esté en funcionamiento,

porque la carcasa puede estar muy caliente.

•El producto no está concebido para una instalación permanente.

•¡El producto es para uso en interiores solamente! Está clasificado como IP20.

•No exponga el producto a lluvia o humedad.

•Asegúrese de que la tensión de la fuente de alimentación usada para el producto

está dentro del rango establecido en el adhesivo o en el panel posterior del

producto.

•Nunca conecte el producto a un atenuador o reostato.

•Sustituya el fusible del producto solo con otro fusible del mismo tipo y categoría.

•Instale el producto en una ubicación con ventilación adecuada.

•Deje al menos a 20'' (50 cm) entre el producto y las superficies adyacentes.

•No bloquee las ranuras de ventilación de la carcasa del producto.

•No haga funcionar el producto a una temperatura ambiente superior a

104 °F (40 °C).

•Nunca mueva el producto agarrándolo por el cable de alimentación o por

cualquier parte móvil.

•Use solamente el soporte de Montaje para mover este producto.

•En caso de un problema grave de funcionamiento, deje de usar el producto

inmediatamente.

•Nunca intente abrir ni reparar el producto. Las reparaciones llevadas a cabo por

personal no cualificado pueden provocar averías o funcionamiento defectuoso.

•Para evitar un desgaste innecesario y alargar su vida útil, desconecte

complemente el producto de la alimentación, mediante el interruptor o

desenchufándolo, durante los periodos en los que no se use.

Contacto

Fuera de EE.UU, Reino Unido, Irlanda, México o Bénelux, póngase en contacto

con su distribuidor para solicitar asistencia o devolver el producto.

Visite

www.chauvetlighting.com para información de contacto.

Shocker™ Panel 180 USB GRR ES

Qué va incluido

•Shocker Panel 180 USB

•Cable de alimentación

•Tarjeta de garantía

•Guía de referencia rápida

Para Empezar

Desembale el Shocker Panel 180 USB con cuidado y compruebe que todas las

piezas están en el paquete y en buen estado.

Si la caja o alguno de los contenidos parecen dañados a causa del transporte, o

muestran signos de manipulación inadecuada, guarde todo el paquete y t

ramite

una reclamación con el transportista inmediatamente. No lo notifique a Chauvet

Si no informa al transportista del daño inmediatamente o no dispone todo el

paquete para inspección podría quedar anulada su reclamación.

Para otras incidencias, como co

mponentes o piezas que falten, daños no

relacionados con el transporte o daños no evidentes, presente una reclamación a

Chauvet

en el plazo de 7 días de la entrega. Para información sobre cómo

contactar con Chauvet, vea la sección Contact Us (contacto) de esta GRR.

Descripción

El Shocker Panel 180 USB es una luz estroboscópica LED de alta potencia con 4

zonas de control para una variedad de atractivos efectos de asombrosa

espectacularidad visual. Tiene una robusta carcasa de

metal y funciona en modos

de Mando a distancia por IR, DMX con o sin cable, Maestro-

Esclavo o

Independiente. Por DMX controla cómodamente sin cables gracias al puerto

D-Fi™ USB integrado.

Vista general

¡ADVERTENCIA! NO enchufe nada que no sea un D-Fi™ USB en el puerto

USB. Si lo hace, podría producir daños al producto.

Entrada de alimentación

Salida de

alimentación

Puerto de

D-Fi™ USB

Salida DMX

Pantalla

Botones de

control

Micrófono

Lazo de

seguridad

Entrada DMX

Portafusibles

Inhaltsverzeichnis

Sprachen:

Andere Chauvet DJ DJ-Equipment Handbücher

Chauvet DJ

Chauvet DJ Obey 40 D-Fi 2.4 Bedienungsanleitung

Chauvet DJ

Chauvet DJ Intimidator Spot 110 Bedienungsanleitung

Chauvet DJ

Chauvet DJ Wash FX Hex Bedienungsanleitung

Chauvet DJ

Chauvet DJ Freedom Cyc Bedienungsanleitung

Chauvet DJ

Chauvet DJ OVATION FD-105WW Bedienungsanleitung

Chauvet DJ

Chauvet DJ Freedom Gobo IP Bedienungsanleitung

Chauvet DJ

Chauvet DJ 4Play 2 Bedienungsanleitung

Chauvet DJ

Chauvet DJ DMX-4 Bedienungsanleitung

Chauvet DJ

Chauvet DJ GigBAR MOVE ILS Bedienungsanleitung

Chauvet DJ

Chauvet DJ Freedom Par H9 IP Bedienungsanleitung

Chauvet DJ

Chauvet DJ Mini 4 Bar 2.0 Bedienungsanleitung

Chauvet DJ

Chauvet DJ LED SHADOW 2 ILS Bedienungsanleitung

Chauvet DJ

Chauvet DJ HURRICANE 1800 FLEX Bedienungsanleitung

Chauvet DJ

Chauvet DJ LED Shadow Bedienungsanleitung

Chauvet DJ

Chauvet DJ GigBAR 2 Bedienungsanleitung

Chauvet DJ

Chauvet DJ Freedom Q1N Bedienungsanleitung

Chauvet DJ

Chauvet DJ Intimidator Scan 110 Bedienungsanleitung

Chauvet DJ

Chauvet DJ EZ Pin Zoom Pack Bedienungsanleitung

Chauvet DJ

Chauvet DJ COLORado 1 Tri TOUR Bedienungsanleitung

Chauvet DJ

Chauvet DJ EVE E-50Z Bedienungsanleitung

Chauvet DJ

Chauvet DJ 4BAR LT BT Bedienungsanleitung

Chauvet DJ

Chauvet DJ COLORbar SMD Bedienungsanleitung

Chauvet DJ

Chauvet DJ INTIMIDATOR SPOT 360X IP Bedienungsanleitung

Chauvet DJ

Chauvet DJ Cosmos HP Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung