Chauvet Intimidator Spot Duo 150 Bedienungsanleitung

Quick Reference Guide

Intimidator™ Spot Duo 150 QRG EN

About This

Guide

The Intimidator™ Spot Duo 150 Quick Reference Guide (QRG) has basic

product information such as mounting, menu options, and DMX values.

Download the User Manual from www.chauvetlighting.com for more details.

Disclaimer

The information and specifications contained in this QRG are subject to

change without notice.

Safety Notes

These Safety Notes include important safety information about installation,

use, and maintenance.

•This product is not intended for permanent installation.

•ONLY connect this product to a grounded and protected circuit.

•Always disconnect from power before cleaning or replacing the fuse.

•DO NOT look at the light source when the product is on.

•Make sure the power cord is not crimped or damaged.

•Never disconnect this product from power by pulling on the cord.

•When mounting this product overhead, use a safety cable.

•DO NOT allow flammable materials close to the unit while operating.

•DO NOT touch this product when it is operating because it may be hot.

•The voltage of the outlet to which you are connecting this product must

be within the range stated on the decal or rear panel of the product.

•This product is for indoor use only! (IP20) To prevent risk of fire or

shock, do not expose this product to rain or moisture.

•Always mount this product in a location with adequate ventilation, at

least 20 in (50 cm) from adjacent surfaces.

•Be sure that no ventilation slots on the unit’s housing are blocked.

•Never connect this product to a dimmer or rheostat.

•Replace the fuse with one of the same type and rating.

•ONLY use the hanging/mounting bracket or base to carry this product.

•The maximum ambient temperature is 104 °F (40 °C). Do not operate

this product at higher temperatures.

•In the event of a serious operating problem, stop using immediately.

•DO NOT open this product. It contains no user-serviceable parts.

•

To eliminate unnecessary wear and improve its lifespan, during periods

of non-use completely disconnect the product from power via breaker

or by unplugging it.

Contact

•From outside the U.S., UK, Ireland, or Mexico, contact the distributor

of record to request support or return a product.

•From inside the U.S., UK, Ireland, or Mexico, use the information in

Intimidator™ Spot Duo 150 QRG EN

What Is

Included

•Intimidator™ Spot Duo 150

•Hanging Bracket with

Mounting Hardware

•Power Cord

•Warranty Card

•Quick Reference Guide

To Begin

Unpack your Intimidator™ Spot Duo 150

and make sure you have received all

parts in good condition. If the box or contents appear damaged, notify the carrier

immediately, not Chauvet.

Description

The Intimidator™ Spot Duo 150 has two Intimidator™ LED 150 moving heads

pre-mounted on a single ba

r. Control options include automated programs,

Sound-

Active modes, and DMX. Pan and tilt functions are available for each

moving head. Lighting options include separate color and gobo wheels, as well as

16 built-in Master/Slave programs.

Overview

Back Panel View

Power In

Fuse

Holder

Digital Display

Buttons

DMX

In/Out

Front Panel View

Power Out

Safety

Loop

Tripod Adjustment

Knob

Cooling Fan

Microphone

Moving

Yokes

Focusing

Lenses

Intimidator™ Spot Duo 150 QRG EN

AC Power

This product has an auto-ranging power supply that can work with an input

voltage range of 100 to 240 VAC, 50/60 Hz.

Power Linking

For the maximum number of Intimidator™ Spot Duo 150 that can be

power linked at 120 V or at 240 V, see the User

Manual or the label on the

product.

Fuse

Replacement

1. Disconnect the product from power.

2. Wedge the tip of a flat-head screwdriver, loosen the fuse holder and pull

straight out.

3. Remove the blown fuse from the safety cap and replace with a fuse of the

exact same type and rating.

4. Re-insert the fuse holder.

5. Reconnect the product to power.

Mounting

Before mounting this product, read the Safety Notes.

Mounting

Diagram

Control Panel

Description

Button

Function

<MENU>

Exits from the current menu or function

<UP>

Navigates upwards through the menu list and increases the

numeric value when in a function

<DOWN>

Navigates downwards through the menu list and decreases

the numeric value when in a function

<ENTER>

Enables the currently displayed menu or sets the currently

selected value into the selected function

Tripod Insertion

Hanging Bracket

Rubber Feet

Intimidator™ Spot Duo 150 QRG EN

Menu Options

Main Level

Programming Levels

Description

DMX Address

d001–d512

Sets the DMX starting address

Automatic

A-01–A-16

Automatic mode

Sound-Active

Srun

Sound-Active mode

Slave

Son1

Slave operating mode 1

Son2

Slave operating mode 2

Sound Sensitivity

S-01–S-99

Sound sensitivity control

Master Auto

M--4

Master built-in 4-head program

M--2

Master built-in 2-head program

Pan 1

PA1

Normal pan operation for head 1

rPA1

Reverse pan operation for head 1

Pan 2

PA2

Normal pan operation for head 2

rPA2

Reverse pan operation for head 2

Tilt 1

til

Normal tilt operation for head 1

rtil

Reverse tilt operation for head 1

Tilt 2

ti2

Normal tilt operation for head 2

rti2

Reverse tilt operation for head 2

Display

dis

Normal display

rdis

Inverted display

Channel Mode

20CH

20-channel DMX personality

17CH

17-channel DMX personality

10CH

10-channel DMX personality

Pan Range

PA36

360° pan range

PA18

180° pan range

Tilt Range

ti27

270° tilt range

ti18

180° tilt range

ti 9

90° tilt range

Reset

rESt

Resets product

Load

LoAd

Loads factory defaults

DMX Linking

The Intimidator™ Spot Duo 150 can work with a DMX controller when

linked by DMX serial connections. Instructions for connecting and

configuring this product for DMX operation are in the User Manual. If you

are not familiar with DMX, download the DMX Primer

from

www.chauvetlighting.com.

Starting

Address

To ensure full access to all channels in each DMX mode, the highest

recommended DMX address is 493.

Master/Slave

Connection

The Intimidator™ Spot Duo 150 uses the DMX data connection for its

Master/Slave mode. Instructions for connecting and configuring this product

for Master/Slave operation are in the User Manual.

Intimidator™ Spot Duo 150 QRG EN

Master Auto

Programs

The Master Auto built-in programs control the actions of two Intimidator™

Spot Duo 150

units linked together by DMX data connection. A single

Intimidator™ Spot Duo 150

(the master) controls the actions of another

Intimidator™ Spot Duo 150

(the slave). Configure the Master Auto programs

in conjunction with the Slave modes as follows:

Master Auto

Head

Program

The Master Auto 4-Head program allows all 4 heads of two linked Intimidator™

Spot Duo 150

units to operate in unison. The master unit will be set to operate in

the M--

4 program, while the slave unit will be set to operate in either Son1 or Son2

mode.

Configure the units as indicated below.

Master unit:

1. Press <MENU>repeatedly until M--2or M--4shows on the display.

2. Press <UP> or <DOWN> to select M--4.

3. Press <ENTER>.

Slave unit:

1. Press <MENU>repeatedly until Son1 or Son2 shows on the display.

2. Press <UP> or <DOWN> to select Son1 or Son2.

•Select Son1 for 100% synchronized actions.

•Select Son2 for a delayed show with all 4 heads in the same direction.

3. Press <ENTER>.

Master Auto

Head

Program

The Master Auto 2-Head program allows a single Intimidator™ Spot Duo 150 to

control the actions of another Intimidator™ Spot Duo 150. The master unit

will be

set to operate in the M--

2 program, while the slave unit will be set to operate in

either Son1 or Son2 mode.

Configure the units as indicated below.

Master unit:

1. Press <MENU>repeatedly until M--2or M--4shows on the display.

2. Press <UP> or <DOWN> to select M--2.

3. Press <ENTER>.

Slave unit:

1. Press <MENU>repeatedly until Son1 or Son2 shows on the display.

2. Press <UP> or <DOWN> to select Son1 or Son2.

•Select Son1 for 100% synchronized actions.

•Select Son2 for the same show with both units, but the actions of the

slave are in the opposite direction of the actions of the master.

3. Press <ENTER>.

Intimidator™ Spot Duo 150 QRG EN

DMX Values

20CH

Channel

Function

Value

Percent/Setting

Pan 1

000 ó255

Pan 0–360° for head 1

Fine Pan 1

000 ó255

Fine panning control for head 1

Tilt 1

000 ó255

Tilt 0–270° for head 1

Fine Tilt 1

000 ó255

Fine tilting control for head 1

Pan 2

000 ó255

Pan 0–360° for head 2

Fine Pan 2

000 ó255

Fine panning control for head 2

Tilt 2

000 ó255

Tilt 0–270° for head 2

Fine Tilt 2

000 ó255

Fine tilting control for head 2

Speed

000 ó255

Pan/Tilt speed (fast to slow)

10 Color Wheel 1

(Head 1)

000 ó005

White

006 ó011

Yellow

012 ó017

Magenta

018 ó023

Green

024 ó029

Red

030 ó035

Cyan

036 ó041

Orange

042 ó047

Blue

048 ó053

Light Green

054 ó063

Amber

064 ó069

White + Yellow

070 ó075

Yellow + Magenta

076 ó081

Magenta + Green

082 ó087

Green + Red

088 ó093

Red + Cyan

094 ó099

Cyan + Orange

100 ó105

Orange + Blue

106 ó111

Blue + Light Green

112 ó117

Light Green + Amber

118 ó127

Amber + White

128 ó191

Rainbow effect with increasing speed

192 ó255

Reverse rainbow effect with increasing speed

Intimidator™ Spot Duo 150 QRG EN

DMX Values (cont.)

20CH

(cont.)

Channel

Function

Value

Percent/Setting

11 Color Wheel 2

(Head 2)

000 ó005

White

006 ó011

Yellow

012 ó017

Magenta

018 ó023

Green

024

029

Red

030 ó035

Cyan

036 ó041

Orange

042 ó047

Blue

048 ó053

Light Green

054 ó063

Amber

064 ó069

White + Yellow

070 ó075

Yellow + Magenta

076 ó081

Magenta + Green

082 ó087

Green + Red

088

093

Red + Cyan

094 ó099

Cyan + Orange

100 ó105

Orange + Blue

106 ó111

Blue + Light Green

112 ó117

Light Green + Amber

118 ó127

Amber + White

128 ó191

Rainbow effect with increasing speed

192 ó255

Reverse rainbow effect with increasing speed

12 Gobo Wheel 1

(Head 1)

064 ó073

Gobo 9 shake with increasing speed

074 ó079

Gobo 8 shake with increasing speed

080 ó085

Gobo 7 shake with increasing speed

086 ó091

Gobo 6 shake with increasing speed

092 ó097

Gobo 5 shake with increasing speed

098 ó103

Gobo 4 shake with increasing speed

104 ó109

Gobo 3 shake with increasing speed

110 ó115

Gobo 2 shake with increasing speed

116 ó121

Gobo 1 shake with increasing speed

122 ó127

Open

128 ó191

Cycle effect with increasing speed

192 ó255

Reverse cycle effect with increasing speed

Intimidator™ Spot Duo 150 QRG EN

DMX Values (cont.)

20CH

(cont.)

Channel

Function

Value

Percent/Setting

13 Gobo Wheel 2

(Head 2)

064 ó073

Gobo 9 shake with increasing speed

074 ó079

Gobo 8 shake with increasing speed

080 ó085

Gobo 7 shake with increasing speed

086 ó091

Gobo 6 shake with increasing speed

092 ó097

Gobo 5 shake with increasing speed

098 ó103

Gobo 4 shake with increasing speed

104 ó109

Gobo 3 shake with increasing speed

110 ó115

Gobo 2 shake with increasing speed

116 ó121

Gobo 1 shake with increasing speed

122 ó127

Open

128 ó191

Cycle effect with increasing speed

192 ó255

Reverse cycle effect with increasing speed

Dimmer 1

000 ó255

Dimmer for head 1 (0–100%)

Dimmer 2

000 ó255

Dimmer for head 2 (0–100%)

16 Shutter 1

(Head 1)

000 ó003

Light off

004 ó007

Light on

008 ó076

Shutter with increasing speed

077 ó145

Pulse strobe

146 ó215

Random strobe

216 ó255

Light on

17 Shutter 2

(Head 2)

000 ó003

Light off

004 ó007

Light on

008 ó076

Shutter with increasing speed

077 ó145

Pulse strobe

146 ó215

Random strobe

216 ó255

Light on

Intimidator™ Spot Duo 150 QRG EN

DMX Values (cont.)

20CH

(cont.)

Channel

Function

Value

Percent/Setting

18 Control Functions

000 ó009

No function

010 ó014

Pan/Tilt blackout

015 ó019

Color blackout

020 ó024

Gobo blackout

025 ó029

Pan/Tilt/Color blackout

030 ó034

Pan/Tilt/Gobo blackout

035 ó039

Color/Gobo blackout

040 ó044

Pan/Tilt/Color/Gobo blackout

045 ó049

No function

050 ó054

First two heads setting

055 ó059

Latter two heads setting

060 ó064

Cancel four heads

065 ó069

No function

070 ó074

Reset

075 ó079

No function

080 ó084

Reverse pan/tilt for both heads

085 ó089

Reverse pan for head 1

090 ó094

Reverse pan for head 2

095 ó099

Reverse tilt for head 1

100 ó104

Reverse tilt for head 2

105 ó109

Cancel reverse pan for head 1

110 ó114

Cancel reverse pan for head 2

115 ó119

Cancel reverse tilt for head 1

120 ó124

Cancel reverse tilt for head 2

125 ó129

Cancel reverse pan/tilt for both heads

130 ó135

No function

136 ó175

Color chase 1 with increasing

speed

When

Channel 19

is active

176 ó215

Color chase 2 with increasing

speed

216 ó255

Color chase 3 with increasing

speed

Andere Handbücher für Intimidator Spot Duo 150

Inhaltsverzeichnis

Sprachen:

Andere Chauvet Scheinwerfer Handbücher

Chauvet

Chauvet Freedom Par RGBA Bedienungsanleitung

Chauvet

Chauvet LED Pinspot 360 Bedienungsanleitung

Chauvet

Chauvet LEDRAIN 64C Bedienungsanleitung

Chauvet

Chauvet SlimPAR HEX 6 IRC Bedienungsanleitung

Chauvet

Chauvet COLORdash Par-Quad 18 Bedienungsanleitung

Chauvet

Chauvet COLORado 1 VW Bedienungsanleitung

Chauvet

Chauvet Pocketspot LED Bedienungsanleitung

Chauvet

Chauvet Q-WASH 360Z-LED Bedienungsanleitung

Chauvet

Chauvet 4 Bar Flex Bedienungsanleitung

Chauvet

Chauvet Nexus 2x2 Bedienerhandbuch

Chauvet

Chauvet Net-X Bedienungsanleitung

Chauvet

Chauvet Scorpion Script Bedienungsanleitung

Chauvet

Chauvet 4BAR Tri Bedienungsanleitung

Chauvet

Chauvet SlimPAR HEX 6 IRC Bedienungsanleitung

Chauvet

Chauvet Intimidator Barrel LED 300 Bedienungsanleitung

Chauvet

Chauvet Rogue R1 FX-B Bedienungsanleitung

Chauvet

Chauvet Nexus Bedienungsanleitung

Chauvet

Chauvet COLORado Ridge IP Bedienungsanleitung

Chauvet

Chauvet Mini Line Dancer CH-215A Bedienungsanleitung

Chauvet

Chauvet COLORstrip Bedienungsanleitung

Chauvet

Chauvet Legend 412 VW Bedienungsanleitung

Chauvet

Chauvet Q-WASH 560Z-LED Bedienungsanleitung

Chauvet

Chauvet BEAMSHOT Bedienungsanleitung

Chauvet

Chauvet COLORstrip Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung