Chauvet Q-WASH 560Z-LED Bedienungsanleitung

Quick Reference Guide

Q-Wash 560Z-LED QRG

Page 2 of 16

About This

Guide

The Q-Wash 560Z-LED Quick Reference Guide (QRG) contains connection

and mounting information, as well as menu options and DMX values.

Disclaimer

Refer to the User Manual for detailed information and instructions. You

can download the User Manual from the CHAUVET® website:

www.chauvetpro.com.

Read ALL the disclaimers and Safety Notes in this document, as well as

those in the product’s User Manual before installing, operating, or

maintaining this product.

Safety Notes

DO NOT open this product unless instructed. It contains no user

serviceable parts.

DO NOT look at the light source when this product is on.

DO NOT touch the product when it is operating because it may be hot.

DO NOT cover the ventilation slots when the product is operating to

avoid internal overheating.

DO NOT install or operate this product where there is less than 50 cm to

the nearest surface to allow adequate ventilation around it.

DO NOT leave any flammable material within 50 cm from this product

while operating or connected to the power outlet to minimize the risk of

fire.

DO NOT carry this product from the head. Use the handles instead.

DO NOT lift the unit by the housing. Use the handles instead.

DO NOT mount this product overhead without using a safety cable.

DO NOT operate this product outdoors or in any location where dust,

excessive heat, water, or humidity may affect it.

DO NOT operate this product if you see damage on the housing, lenses,

or cables. In any of these cases, have the damaged parts replaced by an

authorized technician immediately.

DO NOT connect this product to a dimmer or rheostat.

ONLY connect this product to a grounded and protected circuit.

Q-Wash 560Z-LED QRG

Page 3 of 16

What Is

Included

One Q-Wash 560Z-LED

One IEC Power Cord With

Edison Plug (US market)

One Safety Cable

Two Omega Brackets

Warranty Card

Quick Reference Guide

Features

12 or 15-channel RGBWA LED moving yoke wash product

Pan: 540

Tilt: 270

RGBWA color static mixing with or without DMX control

Vector speed channel for RGBWA color mixing

Variable zoom

Variable electronic strobe

Continuously variable electronic dimmer (0~100%)

Built-in automated programs

Remote product reset and vector speed channel

255-step fully customizable program

Dimming speed control via control panel or DMX

Recall auto or custom programs via control panel or DMX

Color temperature presets (3,200~10,000 K)

Q-Wash 560Z-LED QRG

Page 4 of 16

Product

Description

The Q-Wash 560Z-LED is an RGBWA LED moving yoke wash product.

This product consists of a base section and a moving yoke. The head

contains the 91 RGBWA LEDs and the zoom motors. The base section has

the 3- and 5-pin DMX input and output sockets, the IEC power input

connector, and the LCD-based control panel.

Product Overview

Power Input IEC

Socket

Power Switch

Fuse holder

3-pin DMX In

3-pin DMX Out

5-pin DMX Out

5-pin DMX In

Control panel

Q-Wash 560Z-LED QRG

Page 5 of 16

AC Power

The Q-Wash 560Z-LED has an auto-ranging power supply that works with

an input voltage range of 100~240 VAC, 50/60 Hz.

Replacing

the Fuse

1. Disconnect this product from the power outlet.

2. Using a flat head screwdriver, wedge the tip into the slot of the fuse

holder.

3. Pull out the installed fuse by prying the safety cap out of the housing.

4. Remove the blown fuse from the safety cap and replace with a fuse of

the exact same type and rating.

5. Insert the fuse holder back in place and reconnect power.

Q-Wash 560Z-LED QRG

Page 6 of 16

DMX Linking

The Q-Wash 560Z-LED will work with a DMX controller using a regular

DMX serial connection.

If you are not familiar with the DMX standard, download the DMX Primer

document from www.chauvetpro.com.

DMX Connection

The Q-Wash 560Z-LED uses a regular DMX data connection for its DMX

personalities: Advanced, Basic, and G1.

Download the Q-Wash 560Z-LED User Manual.

Refer to the Setup chapter to learn how to connect this product to DMX.

Refer to the Operation chapter to learn how to configure this product for

DMX.

Master/Slave

Connection

The Q-Wash 560Z-LED uses the DMX data connection for its Master/Slave

mode.

Download the Q-Wash 560Z-LED User Manual.

Refer to the Setup chapter to learn how to connect for master/slave

operation.

Refer to the Operation chapter to learn how to configure master/slave

operation.

Q-Wash 560Z-LED QRG

Page 7 of 16

Mounting

Before mounting this product, read the Safety Notes at the beginning of this

Guide and in the User Manual.

Refer to the Setup chapter in the User Manual for detailed mounting

instructions.

Product

Mounting

Diagram

Floor Mounting

Overhead Mounting

C Clamps (not included)

Omega brackets (included)

Safety cable (included)

Q-Wash 560Z-LED QRG

Page 8 of 16

Programming

Refer to the User Manual for detailed instructions on programming this

product.

Control Panel

Description

Button

Function

<MENU>

Exit from the current menu or function

<ENTER>

Enable the currently displayed menu or accept the currently

selected value

<UP>

Navigate upward through the menu list and increase the

numeric value when in a function

<DOWN>

Navigate downward through the menu list and decrease the

numeric value when in a function

Password

After being prompted, enter the following password by pressing:

<UP>, <DOWN>, <UP>, <DOWN>, <ENTER>.

This password cannot be changed and will be the password you use each

time you are prompted.

Start Address

To ensure you can fully access all channels in each DMX mode, the highest

recommended DMX addresses are as follows:

Mode

Address

Advanced

498

Basic

501

498

Q-Wash 560Z-LED QRG

Page 9 of 16

Menu Options

Main Level

Programming Levels

Description

INTRO

ADDRESS

001~512

Selects a starting DMX address

RESET

NO/YES

Resets the product’s custom settings

FAN

HIGH

Select the fan’s operation mode.

NOTE: Product’s controller will force the fan to

High if the product’s internal temperature becomes

too high, despite any manual or DMX setting

NORMAL

LOW

AUTO

RUN

DMX512

Selects DMX running mode

AUTO 1

Selects the first automatic program

AUTO 2

Selects the second automatic program

CUSTOM

Selects the user customizable program

SLAVE

Selects the Slave running mode

TEST

Starts the product’s test sequence

CHANNELS

BASIC

Selects the 11-channel DMX mode

ADVANCED

Selects the 15-channel DMX mode

DISPLAY

60 CLOSE

Turns off the display after 60 seconds

BRIGHT

Keeps the display on

KEYLOCK

NO/YES

Activates/deactivates the control panel password

DIMMER

DIMMER 4~1

Slow (DIM 4) to fast (DIM1) dimmer curves

DIMMER 0

Linear dimmer

INFO

EDITION

Shows the version of the installed S/W

INVERT

Pan

NORMAL/

REVERSE

Defines the pan direction

Tilt

Defines the tilt direction

Dimmer

Defines the direction of the dimmer fader

Use

NO/YES

Activates the changes

RANGE

P/Start

000~255

Sets the pan start point (restricted range)

P/Finish

Sets the pan end point (restricted range)

T/Start

Sets the tilt start point (restricted range)

T/Finish

Sets the tilt end point (restricted range)

Use

Activates the changes

SPECIAL

Black delay

NO/YES

Activates the move-in black delay (3 s)

Reset

DMX

The DMX controller can reset the product

SYSTEM

The control panel can reset the product

Power

NORMAL/

HIGH

LEDs illuminate at normal or high intensity

NOTE: Product will return to Normal if

temperature becomes too high

Color

White output matches that of older products

RGBTOW

White output set by RGB-W

OFF

White output defined by RGBW faders

Fan

DMX

The DMX controller can set the fan speed

SYSTEM

The control panel can reset the fan speed

Continues on the next page

Q-Wash 560Z-LED QRG

Page 10 of 16

Main Level

Programming Levels

Description

EDIT

STEP

000~255

Selects the program step

PAN

Selects the pan position

TILT

Selects the tilt position

SPEED

Selects the pan/tilt speed

RED

Combines red, green, blue, white, and amber to

obtain a custom color

GREEN

BLUE

WHITE

AMBER

DIMMER

Selects the dimmer value

STROBE

Selects the strobe frequency and mode

ZOOM

Select the zoom position

DIMSPEED

Selects the dimmer speed

TIME

Selects the step duration

USE

No/Yes

Activates the changes

EXTRA

PASSWORD

****

Opens the Extra menu (refer to next page)

Andere Handbücher für Q-WASH 560Z-LED

Inhaltsverzeichnis

Andere Chauvet Scheinwerfer Handbücher

Chauvet

Chauvet SlimPAR HEX 6 IRC Bedienungsanleitung

Chauvet

Chauvet LEDsplash 200B Bedienungsanleitung

Chauvet

Chauvet Swarm 4FX Bedienungsanleitung

Chauvet

Chauvet Q-WASH 560Z-LED Bedienungsanleitung

Chauvet

Chauvet Slim Par Pro TRI Bedienungsanleitung

Chauvet

Chauvet 4 Bar Flex Bedienungsanleitung

Chauvet

Chauvet EZpar T6 USB Bedienungsanleitung

Chauvet

Chauvet COLORado Batten 72 Tour Bedienungsanleitung

Chauvet

Chauvet SlimPAR Pro H USB Bedienungsanleitung

Chauvet

Chauvet Nexus Aw 7x7 Bedienerhandbuch

Chauvet

Chauvet OVATION B-565FC Bedienungsanleitung

Chauvet

Chauvet HURRICANE 1100 Bedienungsanleitung

Chauvet

Chauvet Gobo Zoom LED Bedienungsanleitung

Chauvet

Chauvet Hemisphere 5.1 Bedienungsanleitung

Chauvet

Chauvet GigBar LT Bedienungsanleitung

Chauvet

Chauvet COLORado Range IP Bedienungsanleitung

Chauvet

Chauvet Colorado 1-Quad Tour Bedienungsanleitung

Chauvet

Chauvet COLORado 2-Quad Zoom IP Bedienungsanleitung

Chauvet

Chauvet Rotating Moons CH-208 Bedienungsanleitung

Chauvet

Chauvet Colordash Par-Tri Bedienungsanleitung

Chauvet

Chauvet Abyss Led Bedienungsanleitung

Chauvet

Chauvet Comet LED Bedienungsanleitung

Chauvet

Chauvet COLORado 4 IP Bedienungsanleitung

Chauvet

Chauvet Rogue R2 Wash Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung