Chauvet COLORsplash JR LED-PAR83 Bedienungsanleitung

LED-PAR83

LEDsplash™ Jr.

USER MANUAL

CHAUVET, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A

(800) 762-1084 – (954) 929-1115

FAX (954) 929-5560

www.chauvetlighting.com

2008-11-17/09:40

Table of Content

BEFORE YOU BEGIN........................................................................................................................................................... 3

What is included..................................................................................................................................................................................................................3

Unpacking Instructions........................................................................................................................................................................................................3

AC Power............................................................................................................................................................................................................................3

Safety Instructions...............................................................................................................................................................................................................3

INTRODUCTION ................................................................................................................................................................... 4

Features..............................................................................................................................................................................................................................4

DMX Channel Summary.....................................................................................................................................................................................................4

Product Overview................................................................................................................................................................................................................5

SETUP................................................................................................................................................................................... 6

Power..................................................................................................................................................................................................................................6

Mounting..............................................................................................................................................................................................................................6

OPERATING INSTRUCTIONS.............................................................................................................................................. 7

Master/Slave & Stand-Alone Mode.....................................................................................................................................................................................7

Daisy Chain Connection.....................................................................................................................................................................................................7

Built-in Program Options.....................................................................................................................................................................................................7

Manual Control Options......................................................................................................................................................................................................8

DMX Control Mode..............................................................................................................................................................................................................8

Setting the DMX address....................................................................................................................................................................................................8

APPENDIX........................................................................................................................................................................... 10

DMX Primer.......................................................................................................................................................................................................................10

Fixture Linking...................................................................................................................................................................................................................10

DMX Channel Values........................................................................................................................................................................................................11

Returns Procedure............................................................................................................................................................................................................11

Claims...............................................................................................................................................................................................................................11

DMX Dipswitch Quick Reference Chart............................................................................................................................................................................12

Technical Specifications ...................................................................................................................................................................................................13

Technical Support.............................................................................................................................................................................................................13

LED-PAR83 User Manual 2 2008-11-17 9:40:00 AM

BEFORE YOU BEGIN

What is included

¾1 x LED-PAR83 LEDsplash™ JR

¾1 x Power cable (1 m) and 1 x Linking cable (1.5 m)

¾Warranty Card

¾Users Manual

Unpacking Instructions

Immediately upon receiving a product, carefully unpack the carton, check the contents to ensure that

all parts are present, and have been received in good condition. Notify the shipper immediately and

retain packing material for inspection if any parts appear damaged from shipping or the carton itself

shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture

must be returned to the factory, it is important that the fixture be returned in the original factory box

and packing.

AC Power

AC Voltage Switch Example

To determine the power requirements for a particular product, see the label affixed to the back plate

of the product or refer to the product’s specifications chart. A product’s listed current rating is its

average current draw under normal conditions. All fixtures must be powered directly off a switched

circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit,

even if the rheostat or dimmer channel is used solely for a 0% to 100%

switch. Before applying power, check that the source voltage matches the

product’s requirement. Check the product or device carefully to make sure

that if a voltage selection switch exists that it is set to the correct line

voltage you will use.

Warning! If applicable, verify that the power select switch on your unit matches the line

voltage applied. All fixtures must be connected to circuits with a suitable Earth

Ground.

Safety Instructions

•Please keep this User Guide for future consultation. If you

sell the unit to another user, be sure that they also receive

this instruction booklet.

•Always make sure that you are connecting to the proper

voltage and that the line voltage you are connecting to is

not higher than that stated on decal or rear panel of the

fixture.

•This product is intended for indoor use only!

•To prevent risk of fire or shock, do not expose fixture to

rain or moisture. Make sure there are no flammable

materials close to the unit while operating.

•The unit must be installed in a location with adequate

ventilation, at least 50cm from adjacent surfaces. Be sure

that no ventilation slots are blocked.

•Always disconnect from power source before servicing or

replacing lamp or fuse and be sure to replace with same

lamp source.

•Secure fixture to fastening device using a safety chain.

Never carry the fixture solely by its head. Use its carrying

handles.

•Maximum ambient temperature is Ta: 40°. Do not operate

fixture at temperatures higher than this.

•In the event of serious operating problem, stop using the

unit immediately. Never try to repair the unit by yourself.

Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest

authorized technical assistance center. Always use the

same type spare parts.

•Don’t connect the device to a dimmer pack.

•Make sure power cord is never crimped or damaged.

•Never disconnect power cord by pulling or tugging on the

cord.

•Avoid direct eye exposure to lamp while it is on.

Caution! There are no user serviceable parts inside the unit. Do not open the housing or

attempt any repairs yourself. In the unlikely event your unit may require service,

please contact CHAUVET.

Please read these instructions carefully, which includes important

information about the installation, usage and maintenance?

LED-PAR83 User Manual 3 2008-11-17 9:40:00 AM

CHANNEL INTENSITY CONTROL OF

1 Reserved

2 Blackout/Strobe/Dimmer

3 Red

4 Green

5 Blue

NTRODUCTION

Features

CONTROL FEATURES

•5-channel DMX-512 LED wash light

•Blackout/static/dimmer/strobe

•Static colors and RGB color mixing with or without DMX controller

FEATURES

•Additional power output: max 50 units @ 120V (see manual for details) (115V models only)

•Linkable power with other LEDrain™ and LEDsplash™ units (115V models only)

•Built-in automated programs via master/slave

OPTIONS

•Programmable: Any universal DMX-512 controller

DMX Channel Summary

Red

Green & Blue

Red

Green & Blue

Red

Green & Blue

Red

Green & Blue

Red

LED-PAR83 User Manual 4 2008-11-17 9:40:00 AM

DMX dip

DMX chan

switches:

nel addressing

DMX Connectors

Fuse Power connectiononnection

Hanging yoke

Power lin

Red

Green & Blue

LED-PAR83 User Manual 5 2008-11-17 9:40:00 AM

Product Overview

DMX Connectors

DMX dipswitches:

DMX channel addressing

Fuse Power c

Hanging yoke

Power lin

AC Voltage Switch

Red

Green & Blue

Red

Green & Blue

Red

Green & Blue

Red

Green & Blue

Red

LED-PAR83 User Manual 5 2008-11-17 9:40:00 AM

LED-PAR83 User Manual 6 2008-11-17 9:40:00 AM

Optional Hanging Clamp

SETUP

Power

Warning! Verify that the power indicator label on your unit matche .

All fixtures must be connected to circuits with a suitable Earth Ground.

•To determine the power requirements for a particular fixture, see the label affixed to the back plate

of the fixture or refer to the fixture’s specifications chart.

•A fixture’s listed current rating is its average current draw under normal conditions.

•All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat

(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0%

to 100% switch.

•Before applying power to a fixture, check that the source voltag e fixture’s

requirement.

•All fixtures must be connected to circuits with a suitable Earth Ground.

Power Cable Configuration

CABLE PIN INTERNATIONAL

s the line voltage applied

e matches th

BROWN Live L

BLUE Neutral N

YELLOW/GREEN Earth EG (Ground)

Mounting

Orientation

This fixture can be mounted on a truss using a clamp in any

position.

Rigging

The fixture includes a mounting yoke to which 1 rigging clamp can be bolted.

1. Align the clamp screw with the center hole on the yoke and tighten.

2. Verify the structure can hold 10 times the weight of all to-be installed fixtures.

3. Adjust the angle on the yoke arm as necessary.

Dipswitches 1 ~ 8

(programs)

FUSE POWER

IN AC POWER

OUT AC

IN OUT

DMX512

COLORsplash Jr.

FUSE POWER

IN AC POWER

OUT AC

IN OUT

DMX512

COLORsplash Jr.

Master Setting

Slave Setting

FUSE POWER

IN AC POWER

OUT AC

COLORsplash Jr.

IN OUT

DMX512

FUSE POWER

IN AC PO

OUT AC

COLORsplas

WER

h Jr.

IN OUT

DMX512

FUSE POWER

IN AC POWER

OUT AC

COLORsplash Jr.

IN OUT

DMX512

FUSE POWER

IN AC POWER

OUT AC

IN OUT

DMX512

COLORsplash Jr.

Optional DMX Controller

AC Line

Use 3-pin XLR DMX cable

Use AC linking cable for convenience. As many as 50 par cans

can be powered from one AC daisy chain connection.

Continue

ING INSTRUCTIONS

The LEDsplash™ Jr. is a DMX-512 controllable, full RGB color mix par can made up of highly

efficient and super bright LED’s. There are three color groups (Red, Green and Blue) whose intensity

n be controlled individually allowing the creation of an unlimited range of colors.

Master/Slave & Stand-Alone Mode

wing.

escribed in the section

to OFF.

ion

and all others to the OF

4. You can also run the fixtures in an automatic

stand-alone mode y setting all

as master units.

Daisy Chain Connection

1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector

which will have a (female) 3 pin

ing of a (male) 3 pin connector. Then,

d to connect from the output as stated above to the input of the following fixture and so on.

Built-in Program Options

There are 8 Individual programs that can be

accessed by turning ON dipswitches 1 through 8

individually.

OPERAT

The LEDsplash™ Jr. can operate in Stand-Alone, Master/Slave and via DMX-512 control utilizing 4

channels.

The Master/Slave mode will allow you to link up to as many units you want in a daisy chain fashion. In

this mode, the first unit in the daisy chain will automatically command all other units follo

1. Connect all LEDsplash™ Jr. units in a daisy

chain fashion as d

following.

2. Master Unit: Set dipswitch # 9 to ON and #10

3. Slaves: Set dipswitch # 10 to the ON posit

F position.

by simpl

fixtures to run

of the first fixture

2. Connect the end of the cable coming from the first fixture

connector to the input connector of the next fixture consist

procee

LED-PAR83 User Manual 7 2008-11-17 9:40:00 AM

LED-PAR83 User Manual 8 2008-11-17 9:40:00 AM

RED

GREEN

BLUE

Manual Control Options

With all dipswitches set to the OFF position, Manual Intensity Control

dipswitches 1 through 8 will control 3 levels of

intensity for red and green LED’s and 2

levels of intensity for blue LED’s.

RGB Mix

This allows you to statically set

a color of preference without

the use of a controller. By

choice.

Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to

stomizing or creating a show. In this mode you will be able to control each individual trait of the

using the DMX-512 control protocol than I suggest jumping

“DMX Primer”. It contain rmation that

setting different intensities for

all 3 led colors you can

compose a color of your

DMX Control Mode

fixture and each fixture independently. The LEDsplash™ Jr. uses 4 channels of control.

1. Enable DMX control by setting dipswitc n. Use dipswitches 1 through 9 to

address each fixture accordingly.

Setting the DMX address

This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start

address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data

on the channel indicated by the start address. For example, a fixture that occupies or uses 7 channels

of DMX and was addressed to s s: 100, 101,

102, 103, 104, 105 and 106. Choose start addresses so that the channels used do not overlap and

notate the start address selected for future reference.

h # 10 to the ON positio

tart on DMX channel 100, would read data from channel

If this is your first time addressing a fixture

to the Appendix Section and read the heading

will help you understand its use. s very useful info

LED-PAR83 User Manual 9 2008-11-17 9:40:00 AM

DIP switches located usually on bottom of the fixture. Each

ovide

an be

itch value possible from the

Set the start address using the group of

dip switch has an associated value. Adding the val

the start address. Determining which switches to

accomplished in the following manner. By subtract

ue of each switch in the ON

tog

ing the largest sw

selected start address until zero is achieved.

position will pr

gle ON given a specific start address c

EXAMPLE STARTING ADDRESS

Address 10

Pin # 4 = 8

Pin # 2 = 2

Total = 10

128

256

OPTION

Address 24

= 16

= 8

= 24

Pin # 5

in # 4

Total

Resolving address using

simple math.

ddress 233

233 – (128) = 105, Turn ON Dip # 8

105 – (64) = 41, Turn ON Dip # 7

41 – (32) = 9, Turn ON Dip # 6

9 – (8) = 1, Turn ON Dip # 4

1 – (1) = 0, Turn ON Dip # 1

You will most likely use the first

available number which maybe

number 1. This number was

selected for example purposes.

DIP SWITC VALUE)

H(DMX

128

256

128

256

OPTION

APPEND

DMX PrimerThere are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A

fixture capable of receiving DMX-512 will require one or a number of sequential channels. The user

on the fixture that indicates the first channel reserved in the controller.

There are many different types o fixtures and they all may vary in the total number

. Choosing a start address should be planned in advance. Channels should

never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is

re You can however, control multiple fixtures of the same type using the same starting

a g as the intended result is that of unison movement or operation. In other words, the

w and all respond exactly the same.

signed to receive data through a serial Daisy Chain. A Daisy Chain connection is

T of one fixtu TA IN of the next fixture. The order in which

onnected is not important and has no effect on how a controller communicates to

an order that pr ides for the easiest and most direct cabling. Connect fixtures

conductor twisted pair cable with three pin XLR male to female connectors. The

pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET

carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)

Fixture Linking

Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5

pin to 3 pin adapter. CHAUVET Model No: DMX5M.

The chart below details a proper cable conversion:

3PIN TO 5PIN CONVERSION CHART

Conductor 3 Pin Female (output) 5 Pin Male (Input)

must assign a starting address f DMX controllable

of channels required

set incor ctly.

address s lon

fixtures ill be slaved together

DMX fixtures are de

where the DATA OU re connects to the DA

the fixtures are c

each fixture. Use

using shielded two

shield connection is

Ground/Shield Pin 1 Pin 1

Data ( - )signal Pin 2 Pin 2

Data ( + ) signal Pin 3 Pin 3

Do not use Do not use

COM

DMX +

DMX -

MON

INPUT OUTPUT

Resistance 120

ohm 1/4 een

pin 2 (DM and

pin 3 (DM ) of

the last .

Termination reduces signal errors and to

avoid signal transmission problems and

interference, it is always advisable to

connect a DMX signal terminator.

w betw

X -)

X +

fixture

DMX connector configuration

LED-PAR83 User Manual 10 2008-11-17 9:40:00 AM

Andere Handbücher für COLORsplash JR LED-PAR83

Inhaltsverzeichnis

Andere Chauvet Leuchte Handbücher

Chauvet

Chauvet Q-Spot Bedienungsanleitung

Chauvet

Chauvet DMX-600 Bedienungsanleitung

Chauvet

Chauvet Q-Wash LED Bedienungsanleitung

Chauvet

Chauvet LEG-5000 Handbuch

Chauvet

Chauvet Legend 412Z Bedienungsanleitung

Chauvet

Chauvet SPOT LED 450 Bedienungsanleitung

Chauvet

Chauvet PK PAR64C Bedienungsanleitung

Chauvet

Chauvet Q-Spot 250 Handbuch

Chauvet

Chauvet Q-Wash 419Z-LED Bedienungsanleitung

Chauvet

Chauvet ROGUE RH1 Hybrid Bedienungsanleitung

Chauvet

Chauvet LED Splash LED-PAR196 Bedienungsanleitung

Chauvet

Chauvet Elan Handbuch

Chauvet

Chauvet intimidator scan led 100 Bedienungsanleitung

Chauvet

Chauvet Intimidator Spot 455Z IRC Bedienungsanleitung

Chauvet

Chauvet Q-Wash 575 Handbuch

Chauvet

Chauvet COLORado 3 Betriebsanleitung

Chauvet

Chauvet Legend 1200E Wash Bedienungsanleitung

Chauvet

Chauvet Rogue r2 Beam Bedienungsanleitung

Chauvet

Chauvet DMX-690 Bedienungsanleitung

Chauvet

Chauvet PK PAR56C Bedienungsanleitung

Chauvet

Chauvet S-Mover Bedienungsanleitung

Chauvet

Chauvet DMX-1655R Produkthandbuch

Chauvet

Chauvet COLORado Zoom TOUR Bedienungsanleitung

Chauvet

Chauvet Followspot 1200 Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung