Chauvet LED Splash LED-PAR196 Bedienungsanleitung

LED-PAR196

LED Splash™

USER MANUAL

CHAUVET, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A

(800) 762-1084 – (954) 929-1115

FAX (954) 929-5560

www.chauvetlighting.com

2008-04-02/13:33

Table of Content

BEFORE YOU BEGIN........................................................................................................................................................... 3

WHAT IS INCLUDED..........................................................................................................................................................................................................3

UNPACKING INSTRUCTIONS..............................................................................................................................................................................................3

ACPOWER .....................................................................................................................................................................................................................3

SAFETY INSTRUCTIONS....................................................................................................................................................................................................3

INTRODUCTION ................................................................................................................................................................... 4

FEATURES.......................................................................................................................................................................................................................4

DMXCHANNEL SUMMARY...............................................................................................................................................................................................4

PRODUCT OVERVIEW.......................................................................................................................................................................................................5

SETUP................................................................................................................................................................................... 6

POWER ...........................................................................................................................................................................................................................6

MOUNTING ......................................................................................................................................................................................................................6

OPERATING INSTRUCTIONS.............................................................................................................................................. 7

MASTER/SLAVE MODE.....................................................................................................................................................................................................7

Daisy Chain Connection.....................................................................................................................................................................................7

Dipswitch Options...............................................................................................................................................................................................7

DMXCONTROL MODE.....................................................................................................................................................................................................8

Setting the DMX address...................................................................................................................................................................................8

APPENDIX............................................................................................................................................................................. 9

DMXPRIMER..................................................................................................................................................................................................................9

Fixture Linking....................................................................................................................................................................................................9

DMXCHANNEL VALUES ................................................................................................................................................................................................10

RETURNS PROCEDURE..................................................................................................................................................................................................10

CLAIMS .........................................................................................................................................................................................................................10

DMXDIPSWITCH QUICK REFERENCE CHART.................................................................................................................................................................11

TECHNICAL SPECIFICATIONS..........................................................................................................................................................................................12

TECHNICAL SUPPORT....................................................................................................................................................................................................12

LED-PAR196 User Manual 2 2008-04-02/13:33

BEFORE YOU BEGIN

What is included

¾1 x LED-PAR196 LED Splash™

¾Warranty Card

¾Users Manual

Unpacking Instructions

Immediately upon receiving a product, carefully unpack the carton, check the contents to ensure that

all parts are present, and have been received in good condition. Notify the shipper immediately and

retain packing material for inspection if any parts appear damaged from shipping or the carton itself

shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture

must be returned to the factory, it is important that the fixture be returned in the original factory box

and packing.

AC Power

AC Voltage Switch Example

To determine the power requirements for a particular product, see the label affixed to the back plate

of the product or refer to the product’s specifications chart. A product’s listed current rating is its

average current draw under normal conditions. All fixtures must be powered directly off a switched

circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit,

even if the rheostat or dimmer channel is used solely for a 0% to 100%

switch. Before applying power, check that the source voltage matches the

product’s requirement. Check the product or device carefully to make sure

that if a voltage selection switch exists that it is set to the correct line

voltage you will use.

Warning! If applicable, verify that the power select switch on your unit matches the line

voltage applied. All fixtures must be connected to circuits with a suitable Earth

Ground.

Safety Instructions

•Please keep this User Guide for future consultation. If you

sell the unit to another user, be sure that they also receive

this instruction booklet.

•Always make sure that you are connecting to the proper

voltage and that the line voltage you are connecting to is

not higher than that stated on decal or rear panel of the

fixture.

•This product is intended for indoor use only!

•To prevent risk of fire or shock, do not expose fixture to

rain or moisture. Make sure there are no flammable

materials close to the unit while operating.

•The unit must be installed in a location with adequate

ventilation, at least 50cm from adjacent surfaces. Be sure

that no ventilation slots are blocked.

•Always disconnect from power source before servicing or

replacing lamp or fuse and be sure to replace with same

lamp source.

•Secure fixture to fastening device using a safety chain.

Never carry the fixture solely by its head. Use its carrying

handles.

•Maximum ambient temperature is Ta: 40°. Do not operate

fixture at temperatures higher than this.

•In the event of serious operating problem, stop using the

unit immediately. Never try to repair the unit by yourself.

Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest

authorized technical assistance center. Always use the

same type spare parts.

•Don’t connect the device to a dimmer pack.

•Make sure power cord is never crimped or damaged.

•Never disconnect power cord by pulling or tugging on the

cord.

•Avoid direct eye exposure to lamp while it is on.

Caution! There are no user serviceable parts inside the unit. Do not open the housing or

attempt any repairs yourself. In the unlikely event your unit may require service,

please contact CHAUVET.

Please read these instructions carefully, which includes important

information about the installation, usage and maintenance?

LED-PAR196 User Manual 3 2008-04-02/13:33

INTRODUCTION

Features

CONTROL FEATURES

•7-channel DMX-512 LED par can

•7 individually controlled LED circles produce the full spectrum of colors

FEATURES

•196 LED's distributed into 7 concentric circles

- Red (85), Green (51) and Blue (60)

•Ultra bright LED's

•RGB color mixing

•Built in color change program with 10 selectable speeds

•7 static colors, 5 color pattern chase programs with adjustable speeds and sound active mode via LED-BOSS

COLORbossTM controller

•Up to 100,000-hour LED life span

•Master/Slave mode

OPTIONS

•Optional LED-BOSS COLORbossTM controller

•Programmable: Any universal DMX-512 controller

DMX Channel Summary

CHANNEL INTENSITY CONTROL OF

1 Red

2 Green

3 Blue

4 Red

5 Green

6 Blue

7 Red

LED-PAR196 User Manual 4 2008-04-02/13:33

Introduction

Product Overview

DMX dipswitches:

DMX channel addressing

DMX Connectors

Switch selectable voltage

Fuse

Power plug

Green LED: DMX Signal Indicato

Hanging yoke

7 LED circles are

controlled individually to

create an unlimited range

of visible colors.

Red LED: Power Indicato

LED-PAR196 User Manual 5 2008-04-02/13:33

Introduction

LED-PAR196 User Manual 6 2008-04-02/13:33

SETUP

Power Your product is equipped with switch-selectable AC power setting.

Slide switch up or down

endin

our line volta

Warning! Verify that the power select switch on your unit

matches the line voltage applied. All fixtures must

be connected to circuits with a suitable Earth

Ground.

•To determine the power requirements for a particular fixture, see the label affixed to the back plate

of the fixture or refer to the fixture’s specifications chart.

•A fixture’s listed current rating is its average current draw under normal conditions.

•All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat

(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0%

to 100% switch.

•Before applying power to a fixture, check that the source voltage matches the fixture’s

requirement.

•All fixtures must be connected to circuits with a suitable Earth Ground.

Power Cable Configuration

CABLE PIN INTERNATIONAL

BROWN Live L

BLUE Neutral N

YELLOW/GREEN Earth EG (Ground)

Mounting

Orientation Hanging Clamp

This fixture can be mounted on a truss using a clamp in any position.

Rigging

The fixture includes a mounting yoke to which 1 rigging clamp can be

bolted.

1. Align the clamp screw with the center hole on the yoke and tighten.

2. Verify the structure can hold 10 times the weight of all to-be installed fixtures.

3. Adjust the angle on the yoke arm as necessary.

OPERATING INSTRUCTIONS

The COLORsplash™ is a DMX-512 controllable, full RGB color mix par can made up of highly

efficient and super bright leds. There are seven led circles whose intensity can be controlled

individually allowing the creation of an unlimited range of colors.

The LED Splash™ can operate in Stand-Alone, Master/Slave and via DMX-512 control utilizing 7

channels.

Master/Slave Mode

The Master/Slave mode will allow you to link up to as many units you want in a daisy chain fashion. In

this mode, the first unit in the daisy chain will automatically command all other units following.

1. Connect all LED Splash™ units in a daisy chain fashion as described in the section following.

2. Master Unit: Set dipswitch # 10 to the OFF position and set dipswitches 1-9 according to the

speed desired as indicated below in “Dipswitch Options”.

3. Slaves: Set dipswitch # 1 to the ON position and all others to the OFF position.

4. You can also run the fixtures in an automatic stand-alone mode by simply setting all fixtures to run

as master units.

Daisy Chain Connection

1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector

of the first fixture.

2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin

connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,

proceed to connect from the output as stated above to the input of the following fixture and so on.

Dipswitch Options

DIPSWITCHES (ON ) FUNCTIONS

10 DMX Enable

Blackout (In absence of DMX)

Slave mode in (Master/Slave mode)

None Speed 1 (Slow)

9 Speed 2

9, 8 Speed 3

9, 8, 7 Speed 4

9, 8, 7, 6 Speed 5

9, 8, 7, 6, 5 Speed 6

9, 8, 7, 6, 5, 4 Speed 7

9, 8, 7, 6, 5, 4, 3 Speed 8

9, 8, 7, 6, 5, 4, 3, 2 Speed 9

9, 8, 7, 6, 5, 4, 3, 2, 1 Speed 10 (Fastest)

While in Slave mode, pins 1 – 9 are for

fixture addressing

LED-PAR196 User Manual 7 2008-04-02/13:33

Appendix

DMX Control Mode

Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to

customizing or creating a show. In this mode you will be able to control each individual trait of the

fixture and each fixture independently. The LED Splash™ uses 7 channels of control.

1. Enable DMX control by setting dipswitch # 10 to the ON position on all fixtures and address each

fixture accordingly.

Setting the DMX address

This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start

address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data

on the channel indicated by the start address. For example, a fixture that occupies or uses 7 channels

of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101,

102, 103, 104, 105 and 106. Choose start addresses so that the channels used do not overlap and

notate the start address selected for future reference.

If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping

to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that

will help you understand its use.

Set the start address using the group of DIP switches located usually on bottom of the fixture. Each

dip switch has an associated value. Adding the value of each switch in the ON position will provide

the start address. Determining which switches to toggle ON given a specific start address can be

accomplished in the following manner. By subtracting the largest switch value possible from the

selected start address until zero is achieved.

EXAMPLE STARTING ADDRESS

Address 10

Pin # 4 = 8

Pin # 2 = 2

Total = 10

Address 24

Pin # 5 = 16

Pin # 4 = 8

Total = 24

Resolving address using

simple math.

Address 233

233 – (128) = 105, Turn ON Dip # 8

105 – (64) = 41, Turn ON Dip # 7

41 – (32) = 9, Turn ON Dip # 6

9 – (8) = 1, Turn ON Dip # 4

1 – (1) = 0, Turn ON Dip # 1

You will most likely use the first

available number which maybe

number 1. This number was

selected for example purposes.

DIP SWITCH (DMX VALUE)

128

256

10987654321

256

128

10987654321

256

128

LED-PAR196 User Manual 8 2008-04-02/13:33

Appendix

APPENDIX

DMX Primer

There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A

fixture capable of receiving DMX-512 will require one or a number of sequential channels. The user

must assign a starting address on the fixture that indicates the first channel reserved in the controller.

There are many different types of DMX controllable fixtures and they all may vary in the total number

of channels required. Choosing a start address should be planned in advance. Channels should

never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is

set incorrectly. You can however, control multiple fixtures of the same type using the same starting

address as long as the intended result is that of unison movement or operation. In other words, the

fixtures will be slaved together and all respond exactly the same.

DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is

where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which

the fixtures are connected is not important and has no effect on how a controller communicates to

each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures

using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The

shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET

carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)

Fixture Linking

Note! r with a 5 pin DMX output connector, you will need to use a 5

HAUVET Model No: DMX5M.

Conductor 5 Pin Male (Input)

COMMON

DMX +

DMX -

INPUT OUTPUT

DMX connector configuration Resistance 120

ohm 1/4w between

pin 2 (DMX -) and

pin 3 (DMX +) of

the last fixture.

Termination reduces signal errors and to

avoid signal transmission problems and

interference, it is always advisable to

connect a DMX signal terminator.

If you use a controlle

pin to 3 pin adapter. C

The chart below details a proper cable conversion:

3PIN TO 5PIN CONVERSION CHART

3 Pin Female (output)

Ground/Shield Pin 1 Pin 1

Data ( - )signal Pin 2 Pin 2

Data ( + ) signal Pin 3 Pin 3

Do not use Do enot us

Do not use Do not use

LED-PAR196 User Manual 9 2008-04-02/13:33

Appendix

DMX Channel Values

DEFAULT VALUE FUNCTION

000 Ù255 Red

0 > 100%

000 Ù255 Green

0 > 100%

000 Ù255 Blue

0 > 100%

000 Ù255 Red

0 > 100%

000 Ù255 Green

0 > 100%

000 Ù255 Blue

0 > 100%

000 Ù255 Red

0 > 100%

Returns Procedure

Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.

Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products

returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the

fixture. Be prepared to provide the model number, serial number and a brief description of the cause

for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate

packaging is the customer’s responsibility. CHAUVET reserves the right to use its own discretion to

repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe

method to use.

Claims Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be

reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and

submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim

for items such as missing component/part, damage not related to shipping, and concealed damage,

must be made within seven (7) days of receiving merchandise.

LED-PAR196 User Manual 10 2008-04-02/13:33

Inhaltsverzeichnis

Andere Chauvet Leuchte Handbücher

Chauvet

Chauvet COLORado Zoom TOUR Bedienungsanleitung

Chauvet

Chauvet LG-20 Bedienungsanleitung

Chauvet

Chauvet Moonflower Bedienungsanleitung

Chauvet

Chauvet COLORsplash JR LED-PAR83 Bedienungsanleitung

Chauvet

Chauvet Q-SPORT 560 LED Bedienungsanleitung

Chauvet

Chauvet Scorpion GrafX LG-80 Bedienungsanleitung

Chauvet

Chauvet DMX-685 Bedienungsanleitung

Chauvet

Chauvet LED-BANK4 Bedienungsanleitung

Chauvet

Chauvet SlimPAR 64 RGBA Bedienungsanleitung

Chauvet

Chauvet LED-BAR Bedienungsanleitung

Chauvet

Chauvet DMX-1655R Produkthandbuch

Chauvet

Chauvet COLORado 3 Bedienungsanleitung

Chauvet

Chauvet LED-BAR Handbuch

Chauvet

Chauvet Q-Wash LED Bedienungsanleitung

Chauvet

Chauvet Thruster Bedienungsanleitung

Chauvet

Chauvet Scorpion Scan LG-60 Bedienungsanleitung

Chauvet

Chauvet Q-Wash LED Bedienungsanleitung

Chauvet

Chauvet SPOT LED 450 Bedienungsanleitung

Chauvet

Chauvet COLORado 3 Bedienungsanleitung

Chauvet

Chauvet COLORado 3 Handbuch

Chauvet

Chauvet CH-BOB Jr. Bedienungsanleitung

Chauvet

Chauvet Legend 1200E Wash Bedienungsanleitung

Chauvet

Chauvet PK PAR56C Bedienungsanleitung

Chauvet

Chauvet ROGUE RH1 Hybrid Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung